Service manual

ManualsBrandsSharp ManualsBusiness equipmentUX-118

1 – 10

UX-465L/C

UX-485LU

Normal Dialing

1. Lift the handset or press

2. Dial the fax number.

3. Wait for the reception tone (if a person answers, ask them to press their Start

key).

4. Press:

Rapid Key Dialing

Press the appropriate Rapid Key. Transmission will begin automatically.

Speed Dialing

1. Press:

2. Enter 2-digit Speed Dial number.

3. Press:

RECEIVING DOCUMENTS

Press:

FAX mode: The fax automatically answers on four rings and receives the incoming

document.

TEL mode:

TEL/FAX mode (UX-485LU only):

The fax machine automatically answers on 4 rings and receives faxes. Voice calls

(including manually dialed fax transmissions) are signaled by a special ringing

sound.

TAD mode (UX-485LU): Select this mode when you go out to receive both voice

messages and faxes.

TAD mode (UX-465C): Select this mode when an answering machine is connected

to the fax and the answering machine is turned on.

[5] Quick reference guide (UX-465C/485LU)

INSTALLATION

1. Connect the handset as shown.

2. Plug the power cord into a grounded, 120 V outlet.

3. Plug one end of the telephone line into the "TEL. LINE" jack on the rear of the

fax, and the other end into your telephone wall jack.

RECORDING AN OUTGOING MESSAGE

1. Press:

FUNCTION

Display shows: OGM RECORDING

2. Press:

START/MEMORY

3. Press 1 (GENERAL) to record an outgoing message for the answering ma-

chine. Press 2 (TRANSFER) to record an outgoing message for the Transfer

function.

4. Pick up the handset, press the START/MEMORY key, and speak into the hand-

set to record your message.

5. When finished, replace the handset.

6. Press:

STOP STOP

ENTERING YOUR NAME AND NUMBER

Note: Imaging film and paper must be loaded to perform the following operation.

1. Press:

FUNCTION

Display shows: OWN NUMBER SET

2. Press:

3. Enter your fax number (max. of 20 digits) by pressing the number keys.

♦ If you make a mistake, press the HOLD/SEARCH key to move the cursor

back to the mistake, then enter the correct number or letter.

4. Press:

5. Enter your name by pressing the appropriate number keys as shown below.

♦ To enter two letters in succession that require the same key, press the SPEAKER

key after entering the first letter.

Press the START/MEMORY key:

Enter two digits for the Month (01 through 12).

Enter two digits for the Day (01 through 31).

Enter four digits for the Year (Ex: 2001).

Enter two digits for the Hour (01 through 12).

Enter two digits for the Minute (00 through 59).

Press the

key for A.M. or the # key for P.M.

When finished, press:

STORING AND CLEARING NUMBERS FOR AUTO DIALING

Note: Imaging film and paper must be loaded to perform the following operation.

1. Press:

Display shows: FAX/TEL # MODE

2. Press 1 to store a number or 2 to clear a number.

3. Enter a 2-digit Speed Dial number (from 01 to 05 for Rapid Key Dialing, or 06

to 45 for Speed Dialing). (If you are clearing a number, go to Step 7.)

4. Enter the full telephone/fax number.

5. Press:

6. Enter the name of the location by pressing number keys (max. of 20 charac-

ters).

(Refer to the letter entry table in

ENTERING YOUR NAME AND NUMBER

7. Press:

TEL.

SET

TEL.

LINE

6. When finished, press:

START/MEMORY

A =

B =

C =

D =

E =

F =

G =

H =

I =

J =

K =

L =

M =

N =

O =

P =

Q =

R =

S =

T =

U =

V =

W =

X =

Y =

Z =

SPACE =

SPEAKER

HOLD/

move

REDIAL

HOLD/

SPEAKER

123

GHI JKL MNO

TUV WXYZPQRS

SPEED

DIAL

ABC DEF

Deletes high-

lighted letter

Upper/lower

case shift key

Moves cursor

to the left

Moves cursor

to the right

Press either key one or more times to select

and enter a symbol.

START/MEMORY

STOP

FUNCTION (UX-465C)

FUNCTION (UX-485LU)

FUNCTION

SPEAKER

SPEED

DIAL

RECEPTION

MODE

FAX

TEL

TAD

FAX

TEL

TAD

FAX

TEL

TAD

FEB 1 10:30

(UX-465C)

FAX

TEL

TAD

FAX

TEL

TAD

FAX

TEL

TAD

FEB 1 10:30

(UX-485L)

TEL/FAX

FAX

TEL

TAD

FEB 1 10:30

TEL/FAX

Fax

tone

RECEIVING

START/MEMORY

STOP

START/MEMORY

STOP

START/MEMORY

SETTING THE DATE AND TIME

Note: Imaging film and paper must be loaded to perform the following operation.

Press:

Display shows: DATE & TIME SET

SENDING DOCUMENTS

Place your document (up to 10 pages)

face down in the document feeder.