Installation Guide

ManualsBrandsSharp ManualsAppliancesSharp 24" Stainless Steel Smart Convection Microwave Drawer Oven

1 E

Convection Microwave Drawer: SMD2499FS

INSTALLATION MANUAL

IMPORTANT NOTES TO THE INSTALLER

• Read all of the Installation Manual before installing the

Convection Microwave Drawer.

• Remove all packing material before connecting the electrical

sup ply.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the consumer.

IMPORTANT NOTES TO THE CONSUMER

Keep this manual with your Operation Manual for future reference.

• As when using any oven generating heat, there are certain safety

precautions you should follow. These are listed in the Operation

Manual. Read all and follow carefully.

• Be sure your Convection Microwave Drawer is installed and

grounded properly by a qualied installer or service technician.

• This unit comes equipped with a Wi-Fi connectivity option.

In order to activate the Wi-Fi functionality, the area in which

the unit is installed requires a Wi-Fi signal. Please see the

operation manual for the minimum Wi-Fi specications.

IMPORTANT SAFETY INSTRUCTIONS

If the information in this manual is not followed

exactly, a re or electrical shock may result that could cause property

damage, personal injury or death.

• This Convection Microwave Drawer must be electrically

grounded in accordance with local codes.

• Make sure the wall coverings and the cabinets around the

Convection Microwave Drawer can withstand the heat

generated by the Convection Microwave Drawer.

NEVER LEAVE CHILDREN ALONE OR

UNATTENDED IN THE AREA WHERE A CONVECTION MI-

CROWAVE DRAWER IS IN USE. NEVER LEAVE THE DRAWER

OPEN WHEN THE OVEN IS UNATTENDED.

STEPPING, LEANING OR SITTING ON THE

DRAWER MAY RESULT IN SERIOUS INJURIES AND CAN

ALSO CAUSE DAMAGE TO THE CONVECTION MICROWAVE

DRAWER.

• Do not use the Convection Microwave Drawer as a storage

space. This creates a potentially hazardous situation.

• Check that the time-of-day is in the display. If not, touch STOP/

CLEAR for safety reasons and to prevent unintended use.

SPECIAL WARNING

• INSTALLATION AND SERVICE MUST BE PERFORMED

BY A QUALIFIED INSTALLER.

• IMPORTANT: SAVE this installation manual FOR

LOCAL ELECTRICAL INSPECTOR’S USE.

• READ AND SAVE THESE INSTRUCTIONS FOR

FUTURE REFERENCE.

CLEARANCES AND DIMENSIONS

For SAFETY CONSIDERATIONS do not install drawer

in any combustible cabinetry, which is not in accord

with the stated clearances and dimensions on pages

2 - 4. See Figures 1 - 7.

UNPACKING YOUR CONVECTION

MICROWAVE DRAWER

A minimum of two people are required to handle the oven. Use

the two handles located on each side of the oven to lift.

1 Remove all packing materials from inside the Convection Micro-

wave Drawer and on the Drawer door.

2 Remove the feature sticker, if there is one. Check the drawer for

any damage, such as misaligned or bent drawer, damaged drawer

seals and sealing surfaces, broken or loose drawer guides and dents

inside the cavity or on the front side of the drawer. If there is any

damage, do not operate the Convection Microwave Drawer and

contact your dealer or a SHARP AUTHORIZED SERVICER.

Sealing

Surface

Oven

Cavity

Sealing

Surface

Summary of content (8 pages)

PAGE 1
Convection Microwave Drawer: SMD2499FS INSTALLATION MANUAL SPECIAL WARNING IMPORTANT NOTES TO THE INSTALLER • Read all of the Installation Manual before installing the Convection Microwave Drawer. • INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. • IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE. • READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. • Remove all packing material before connecting the electrical supply.
PAGE 2
CLEARANCES AND DIMENSIONS It can also be installed under: Wall Ovens: Gas or Electric SuperSteam oven: SSC2489DS Cooktop Models: SDH3042DB, SDH3652DB, SCR3042FB, SCR2442FB, SCR3041GB, SCH3043FB, SCH2443FB, SDH3042DB or SDH3652DB. • Be sure that the clearance of the floor between the wall oven and the Convection Microwave Drawer is a minimum of 2-inches. • The Convection Microwave Drawer interior will easily accommodate a 9" x 13" oblong dish or a bag of microwave popcorn.
PAGE 3
24" CONVECTION MICROWAVE DRAWER STANDARD MOUNT AND MEASUREMENTS Figure 3 represents a typical standard cabinet. If installed in custom cabinets with extended countertops, take into account visibility and access to controls. See Figure 4. Move oven location downward for extended countertops Extended countertops A C B E Figure 4 E C D G F Figure 3 A. 25" (635 mm) B. 1/2" (12.7 mm) minimum C. 19 1/2" (495.3 mm) D. 36" (914.40 mm) E. Control panel shown in open position F. 24" (609.60 mm) G.
PAGE 4
24" CONVECTION MICROWAVE DRAWER FLUSH MOUNT AND MEASUREMENTS Prepare cabinet opening as shown in Figures 5, 6, 7 A A. Suggested electrical outlet location B. 5" (127 mm) C. 4" (101.60 mm) D. 23 7/8" (606.43 mm) E. 19 3/8" (492.12 mm) F. 1 5/8" (41.27 mm) G. 23 1/2" (596.90 mm) minimum depth H. 22 3/8" (568.32 mm) I. 1 5/8" (41.27 mm) to front of shelf J. 19 3/4" (501.65mm) opening K. Floor must support 125 lbs (56.
PAGE 5
ELECTRICAL OUTLET DRAWER INSTALLATION The electrical requirements are a 120 volt 60 Hz, AC only, 15 amp. or more protected electrical supply. It is recommended that a separate circuit serving only this appliance be provided. 1. Place the Convection Microwave Drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical outlet. Note: If you have any questions about the grounding or electrical instructions, consult a qualified electrician or serviceperson. 3.
PAGE 6
MODEL AND SERIAL NUMBER LOCATION BEFORE YOU CALL FOR SERVICE The nameplate includes model and serial number. Open the Convection Microwave Drawer fully. The label is located at the bottom left side of the oven face plate. Read the BEFORE YOU CALL and operating instruction sections in your Operation Manual. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this oven.
PAGE 7
PAGE 8
SHARP ELECTRONICS CORPORATION • 100 Paragon Drive • Montvale, New Jersey 07645 • USA T IN S EB 5 8 0 MRR1 A p r 21, 2 0 21