Operation Manual
Table Of Contents
- (B059)_cover
- (B059)_Eng
- WARNING
- CAUTION
- INSTALLATION
- WARNING
- 1 Keep adequate ventilation space around the refrigerator.
- 2 Using the two front adjustable feet, ensure that the refrigerator is positioned firmly and level on the floor.
- 3 Remove the 2 screws of the cabinet lower part, and use these to fit the foot covers. (supplied inside the refrigerator compartment)
- 4 Connect the power plug to a 230/240 volt. 10 amp. power point.
- DESCRIPTION
- 1. Freezer shelf
- 2. Ice cube maker
- 1) Do not over fill the Ice cube trays; otherwise the ice cubes will be joined together when frozen.
- 2) When the ice cubes are made, turn the lever clockwise to empty the ice into the Ice cube box.
- 3. Ice cube box
- 4. Fresh case & door
- 5. Refrigerator light
- 6. Temp. control knobs
- 7. Refrigerator shelves (2 pcs.)
- 8. Hybrid cooling panel (Aluminum panel)
- 9. Fruit and vegetable shelf
- 10. Fruit and vegetable crisper (2 pcs.)
- 11. Adjustable feet & covers (2 pcs.)
- 12. Magnetic door seals (2 pcs.)
- 13. Flexible pocket
- 14. Door pockets (2 pcs.)
- 15. Water tank
- 16. Utility pockets (2 pcs.)
- 17. Egg holder
- 18. Bottle pocket
- 19. Bottle stopper / Tube stand
- 20. Water dispenser
- WATER DISPENSER
- WARNING
- How to dispense water
- WARNING
- IMPORTANT
- 1 Remove the accessories e.g. shelves from the cabinet and door. Wash them in warm soapy dishwashing water; rinse in clean water and dry. (Only fruit and vegetable shelf is not removable.)
- 2 Clean the inside with a cloth soaked in warm soapy dishwashing water. Then, use cold water to wipe off soapy water.
- 3 Wipe the exterior with a soft cloth each time it is soiled.
- 4 Clean the magnetic door seal with a toothbrush and warm soapy dishwashing water.
- 1 Push the lever and let out all water in the water tank.
- 2 Remove the pipe cover. Disconnect the both ends of the joint pipe.
- 3 Remove the water tank from the door.
- 4 Remove the cover and take out the mesh filter.
- 1. Remove all food.
- 2. Remove the power plug from the power point.
- 3. Clean and dry the interior thoroughly.
- 4. Ensure that all the doors are wedged open slightly for air circulation.
- BEFORE YOU CALL FOR SERVICE
- SPECIFICATION
33
1. Freezer shelf
2. Ice cube maker
1) Do not over fill the Ice cube trays;
otherwise the ice cubes will be
joined together when frozen.
2) When the ice cubes are made,
turn the lever clockwise to empty
the ice into the Ice cube box.
NOTE To prevent damage to the Ice
cube box, do not make ice in
the Ice cube box.
3. Ice cube box
4. Fresh case & door
5. Refrigerator light
6. Temp. control knobs
Adjustable by turning each knob.
7. Refrigerator shelves (2 pcs.)
8. Hybrid cooling panel (Aluminum panel)
The panel is cooled from the rear, thus indirectly
cooling the refrigerator compartment. In this way, food
is refrigerated gently, without exposing it to cold air flow.
9. Fruit and vegetable shelf
10. Fruit and vegetable crisper
(2 pcs.)
11. Adjustable feet & covers (2 pcs.)
12. Magnetic door seals (2 pcs.)
13. Flexible pocket
Tall food items (e.g. pizza box)
can be stored by lifting the
partition from the bottom of
the pocket.
14. Door pockets (2 pcs.)
15. Water tank
16. Utility pockets
(2 pcs.)
17. Egg holder
18. Bottle pocket
19. Bottle stopper / Tube stand
Prevents bottles etc. from falling.
Stick-type food products can also
be stored inside.
20. Water dispenser
Attach the tray included in
the package.
DESCRIPTION
16
17
12
14
20
15
11
1
2
3
4
5
7
8
9
10
6
12
13
14
18
19
Ice cube box
Lever
(for refrigerator) (for freezer)
Tray
Deodorising unit
A deodorising catalyst is installed on the routes of cold
air. No operation and cleaning required.
Defrosting
Defrosting is fully automatic due to a unique energy
saving system.
If a refrigerator lamp blows
The lamp should only be replaced by a SHARP
approved service centre.
(B059)_Eng.fm Page 3 Thursday, September 17, 2009 10:58 AM