INTRODUCTION Welcome to the world of compact copying using this epithet copier has been designed for greater copying erstwhile occupying a minimum amount of space and featuring intuitive operating ease. Special features inclusive: ® 55 step-zoom copying, # Stationary platen, # Auto start mode, ® Two-way paper feed, ® Malicious exposure control, * Co lour copying. To get full use of all copier features, te sure to familiarize yourself with this manual and the copier.
Remove the contents in the following order. —Operation Manual = Paper Casseroles Power Cord Carton *Save the canter and packing materials. The carton and packing can be re-used for transporting the machine, should it be necessary.
A WORD ON COPIER INSTALLATION Improper install the following d copier is moved. on may damages ihe copier. Pleads note ding initial installation and whenever the . Be sure to use a correctly rated power supply and to ground (he cooler. 2. Do not plug the copier info an outlet used by other appliances. w . Do not install your copier in areas halt are: ® damp, humid, or very dusty, & exposed to direct sunlight, ® poorly ventilated, ® subject to extreme temperature or humidity changes, e.g.
Remove the copier from the bag. Press the buttons on both sides of the cooler and open the front cover. Remove tapes (A) and (B). Remove tape (C) to open the multi feed bypass. If the drum cartridge is factory installed, remove tape (A) and remove the spacer where the developer cartridge is rinsed. Then skip steps 3 through 6 and proceed o step 7. Press the upper half release button to open the copier. Remove the caver from the drum cartridge. Tide the drum cartridge into place.
9. Slide the developer cartridge in until it locks in place. 10. Close the front cover. 11, Remove the mirror base fixing pin and the protective packing material from the back of the document cover. Note: Be sure io remove ihe mirror has fixing pin before turning on the power switch. Failure to do so may cause malfunctioning. 12. Remove the paper cassette from the bag. 13. Fan the copy paper and insert it into the cassette. {Maximum: 250 sheets) See LOADING COPY PAPER, page 12.
POSIES © Open the document cover. © Place the original document in the lower left corner, and close the document cover. © Select the number of copies desired. & The maximum number of copies is 50. ® Press the right copy quantity key (A} to set unit digit from 0 o 9. This key will not change the tens digits. ® Press the left copy quantity key to set the tens digit from 1 10 5. Setting the number to § will automatically change the single units digit mistake is made, press the clear key (C) and start again.
o T Automatic Power Save Mode The copier enters the power save mode and the READY indicator starts blinking approximately 90 sec. after the last copy is made. Copying is possible in the power save made, but the first copy may take a few seconds longer than usual Reproving the Document Cover:/ When the originals are large, the document cover can be removed o easily make copies. 1, Open the document cover. 2. Lift the document cover at a slight forward angle and remove it.
ENLARGEMENT/ZOOM Two preset reduction ratios 70% and 80% {75% and 95%) and one pres: enlargement ratio 122% (124%) can be selected. The zoom function enables copy ratio selection from 70% o 124%. BY PA PAPER SE( A COPYCATTING Place the original on the document glass and close the document cover. 2. Press the copy ratio key the zoom key ta select the desired copy ratio. ® The indicated enlargement ratio does not correspond exa 0 the indicated pacer combination (inch system only).
MULTI BY-PASS FEED (SPECIAL PAPERS) The multi feed by-pass can be used to multi feed standard paper up 1o & loll | purpose papers. I3, use only Sharp recommended supplies. The maximum copy 72 x 14", The minimum copy size 1. Set the original document face down on the document glass, and close the document cover. 2. Open the multi feed by-pass and set the by-pass guide to the width of the copy paper. 3.
Two-sided copies can also be made on the copier by using the multi feed bypass. i n’ 1. Place the first original document (e.g. B) on the document glass and make a copy. The first copy can be made with paper from a cassette or the multi feed bypass Replace original document B with original document C and close the document cover. Note that the orientation of the first and second originals is reversed. . Turn the first copy (B) over, and feed it into the multi feed by-pass.
Co lour developer cartridges (sold separately) can be installed to copy one colon limey. Multiple colors can be copied on the same page by changing the color developer cartridges and recopying on the same copy paper. To order color developer cartridges, use (he part cote 1 helot. Black (SF-810DC10) Rea 0DC2) Blue 10DC3;} Brown ) Green (5F-610DC5) 1. Inst ail the desired color developer cartridge. ¢ See DEVELOPER CARTRIDGE REPLACEMENT, page 14 2.
8 appears In the copy quantity display when the paper cassette or multi deaf by-pass is employ or when the paper has not been fed all the way in. (f the cassette is empty, load paper according to the following procedures: 4. Push the pressure plate until it socks in position. Adjust the paper guides on the cassette to the copy paper width and length. Fan the copy paper and insert it into the cassette. Make sure the edges go under the corner hooks. The cassette holds a maximum of 250 sheets of paper.
" MISDEED REMOVAL When [8%] blinks, the copier sips because of a misdeed If the paper is accidentally torn when removing a misdeed, be sure (o remove all pieces. Be careful not to damage the superconductive drum or corona wires, . .1 1. Open the front cover. 2. Press the upper naif release button to open the copier. Carefully remove the missed paper. 4. Lift the green fusing fever to remove a misdeed in the fusing area. CAUTION THE FUSING AREA 1S HOT, 5. Close the upper half and the front cover. 6.
() blinks when the enveloper cartridges is employ of toner. The copier stops after the Cop Y run in progress has been competed. Tre service | f the developer cartridge is estimated 1o be 4,000 (black), 2,700 {color) copies of average letter type originals. If originals hay ng pictures or other large dark areas are copied, th enveloper fife will be reduced accordingly.
' DRUM CARTRIDGE REPLACEMENT (& lights up fare approximately 11,000 copies have bean made. This kinds hepatitis age ihe drum cartridge. ng approximately 1,000 more copies, the copier will stop. Be sure new drum cartridge ready for replacement 1. Open the front cover. 2. Press down on the catch and pull out the developer cartridge. 8. Press the upper half release button to open the copier. 4. Pull out the drum cartridge. 5. Remove the cover from the new drum cartridge. 6.
Proper care is essential in order to get clean, sharp copies. Be sure 10 take a few minutes to regularly clean your copier. Stains on the glass or cover will also be copied. Wipe the glass and cover with a soft, clean cloth. If necessary, dampen the cloth with water or a glass cleaner, Do into use thinner, benzene, or other volatile cleaning agents. 1. Open the front cover. 2. Slide the built-in charge corona cleaner in and out a few times as shown in the figure. 1. Open the front cover and the upper hail.
COPIER TROUBLE? Copier does not work. ® Copier plugged in? ® Po war switch ON? Copier is on but does not copy. ® Are any trouble indicators on? ® s there paper in ihe cassette? Copying is not possible from the multi feed by-pass. & Is the by-pass indicator lit? Blank copies o I3 the original document placed Ace down on the document grass? Light or dark copes ® Adjust the exposure control.
Striped copies ® Is the document glass or cover dirty? —» Seg p. 16 ® Clean the charge and transfer coronas. i See 0. 16 Paper misdeeds frequently. ® Is the exit tray fully opened? —» Seep. 4 ® I the copy paper properly loaded in the cassette and the geisha Zdju'gtegto the paper size? =™ Seep. 12 ® Is the copy paper damp? Use only dry, flat copy paper. ® Were "special papers’ fed from the cassette? > See 0. 9 ® Does the paper elev! in the multi feed by-pass .
MOVING INSTRUCTIONS 1. Open the copier and remove the developer cartridge. ® Re-install the shipping cover on the developer cartridge 2. Remove the paper cassette and the power cord. 3. Close the copier and securely gape the exit tray, multi feed by-pass and document cover. 4. Pack the copier by reversing the UNPACKING instructions on page 2.
Type Desk-top Copy system Dry, electrostatic transfer system Originals Sheets, bound documents Original size Max. B4 (10" x 14%) Copy sizes ;&4 X 14") t0 A5 X by cassette ead. (97169 Ult Total thickness by-pass feed Approx. 5C sheets ((75 fir? (20 Abs) paper)) Approx. 40 sheets (80 g/m¥# (21 Abs) paper)) Copy speed {at 1:1 copy ratio} 10 copies/min, (A4, AB x 11", x 8 completeness. 14%) Continuous cog Max. 50 copies; subtraction counter First copy time Approx. 9 sec. {In normal copy mode) Approx. 20 sec.
Fusing system Developing sierra Heat rollers Magnetic brush development Light source Fowler supply Power consumption Halogen imp Local collage +10% Max. 1.15 kKW Gross dimensions BB0 (W) x 440 (D) mm (33-55, x (D)) Weight Copier dimensions Approx. 24Kg (52.
