501CC 501cc-gb-02.
9 8 501DF, 501DP, 501DFX, 501DV ATEX II 2 G T4 501F, 501P, 501X, 501V ATEX 2
Declarations Declaration of conformity Declaration of Incorporation When this pump unit is used as a stand alone pump it complies with: Machinery Directive 2006/42/EC, EMC Directive 2004/108/EC. . When this pump unit is to be installed into a machine or is to be assembled with other machines for installations, it must not be put into service until the relevant machinery has been declared in conformity with the Machinery Directive 2006/42/EC.
DO use valves with a straight fluid path. DO use slow sweeping bends with minimum radius equal to four to five times the tubing diameter. DO keep the pumphead rollers and track clean. The self-priming nature of peristaltic pumps means valves are not required. Any valves fitted must cause minimum restriction to flow in the pumping circuit.
Start up Before starting and after prolonged storage of the gear units, remove the plug from the vent screw on top of the casing to avoid excessive pressure in the gearbox, which may cause leakage at the shaft seals. Troubleshooting Should the pump fail to operate, make the following checks to determine whether or not servicing is required. • Check the electrical supply is available at the pump. • Check that the pump is not stalled by incorrect fitting of tubing.
Installation A muffler is supplied with the air motor, but not installed. Install a moisture trap and filter in the air line ahead of the motor. If condensates need to be flushed out of the motor, use clean, dry air at low pressure. For efficiency of output and speed control, use air lines of the same size or next pipe size larger than the intake port of the motor. A 4 way valve which can be connected by piping to both air ports of the motor will make reversing possible.
501RLC Installation. Simplex (single pumphead) units and duplex (twin pumphead) units Isolate motor from mains supply. Fit the track in any one of three orientations, over the drive shaft and locating boss. Secure the track with the four locating screws. Ensure the drive shaft is degreased before locating the rotor onto the shaft via the split collet. Rotate the rotor until its guide rollers are aligned flush to the front edge of the track.
501RLC tube loading. Duplex (twin pumphead) units Isolate the pump from mains supply. Unlock and open the hinged guard. Swing out the rotor crank handle until it locks into position. Loosen the rotor screw and give the rotor a sharp tap to release it. Pull the rotor slightly forward from its seated position on the drive shaft so that the pinned collet clears the drive shaft dog and it can rotate freely . Select the length of tubing required, noting that approximately 240mm is required for the track systems.
501RLC Pumphead spares Number 1 2 3 4 5 6 7 8 9 9 10 10 11 Spare MN 1200M FN 4502 FN 2341 MN 0266M MNA0114A FN 2332 FN 0422 MN 0011T MNA0143A MNA0511A SG0001 SG0002 MN 0012T Description Lockable guard Lock Hinge screw Hinge grey Tube clamp assembly Screw Screw (x 4) Main roller 501RLC Rotor assembly 501RL2C Rotor assembly Spring standard (1.6) Spring hard (2.
Technical Data # English Tube number Gearbox lubricant Mineral Oil (165) Tube bore rpm Pressure(+) Energol GR-XP 220 EnergolGR-XP 100 Bartran HV15 Suction Mobil-gear 630 Mobil-gear 629 Mobil DTE 11M 501F/RL, 501I/RL, 501TI/RL - 100ml 601F/R, 601I/R, 601TI/R - 250ml Motor wiring 10 Counter-clockwise (165) Clockwise (rpm) Shell Omala Oel 220 Shell Omala Oel 100 Shell Tellus Oel T 15
501RLC, 501RLC2 (ml/min) Flow rates # mm “ 112 0.5 1/50 13 0.8 1/32 14 1.6 1/16 16 3.2 1/8 25 4.8 3/16 17 6.4 1/4 18 8.0 5/16 60 213 291 2.5 8.9 12 7.4 26 36 26 91 120 110 400 540 240 860 1200 380 1400 1900 600 2100 2900 62 223 281 2.6 9.3 12 7.6 27 34 26 95 120 120 410 520 250 900 1100 390 1400 1800 620 2200 2800 6 - 60 0.25-2.5 0.74-7.4 2.6-26 11-110 24-240 38-380 60-600 21 - 213 0.88-8.9 2.6-26 9.0-91 39-400 85-860 130-1400 210-2100 29 - 291 6 - 62 1.2-12 0.25-2.
501RLC, 1.6mm Product codes mm 0.5 0.8 1.6 3.2 4.8 6.4 8.0 “ 1/50 1/32 1/16 1/8 3/16 1/4 5/16 # 112 13 14 16 25 17 18 Marprene 902.0005.016 902.0008.016 902.0016.016 902.0032.016 902.0048.016 902.0064.016 902.0080.016 Bioprene 903.0005.016 903.0008.016 903.0016.016 903.0032.016 903.0048.016 903.0064.016 903.0080.016 Pumpsil 913.0005.016 913.0008.016 913.0016.016 913.0032.016 913.0048.016 913.0064.016 913.0080.016 mm 0.8 1.6 3.2 4.8 6.4 8.
501RLC Flow rates 13
501F/R 501DF/R 62rpm model 223 rpm model 501FX/RL 345 85 75 230 250 220 340 14
Switch Watson-Marlow, Bioprene, Pumpsil and Marprene are trademarks of Watson-Marlow Limited. Tygon is a trademark of the Saint-Gobain Performance Plastics Company. Fluorel is a trademark of 3M. Sta-Pure and Chem-Sure are trademarks of W.L Gore and Associates. Warning, These products are not designed for use in, and should not be used for patient connected applications.
Product use and decontamination declaration In compliance with the UK Health & Safety at Work Act and the Control of Substances Hazardous to Health Regulations you, the user are required to declare the substances which have been in contact with the product(s) you are returning to Watson-Marlow or any of its subsidiaries or distributors. Failure to do so will cause delays in servicing the product.
