Technical information

7
ds_x61_en_ssr_technical_information: 011212D
11. The following shows the packaging format
1) Tape and reel (Phototriac coupler)
mm inch
Type Tape dimensions Dimensions of paper tape reel
SO package
4-pin type
(1) When picked from 1/2-pin side: Part No. APT❍❍❍❍SX (Shown above)
(2) When picked from 3/4-pin side: Part No. APT❍❍❍❍SZ
DIP
4-pin type
(1) When picked from 1/2-pin side: Part No. APT❍❍❍❍AX
(2) When picked from 3/4-pin side: Part No. APT❍❍❍❍AZ
DIP
6-pin type
(1) When picked from 1/2/3-pin side: Part No. APT❍❍❍❍AX
(2) When picked from 4/5/6-pin side: Part No. APT❍❍❍❍AZ
10. Soldering
1) When soldering PC board terminals,
keep soldering time to within 10 s at
260C 500F.
2) When soldering surface-mount
terminals or SO package, the following
conditions are recommended.
(1) IR (Infrared reflow) soldering method
(2) Soldering iron method
Tip temperature: 350 to 400C 662 to
752F
Wattage: 30 to 60 W
Soldering time: within 3 s
(3) Others
Check mounting conditions before using
other soldering methods (DWS, VPS,
hot-air, hot plate, laser, pulse heater, etc.)
• The temperature profile indicates the
temperature of the soldered terminal on
the surface of the PC board. The ambient
temperature may increase excessively.
Check the temperature under mounting
conditions.
• When using lead-free solder we
recommend one with an alloy
composition of Sn3.0Ag0.5Cu. Please
consult us regarding details such as
soldering conditions.
T1
T2
T3
T1 = 150 to 180°C
T2 = 230°C
T3 = 250°C
t1 = 60 to 120 s or less
t2 = 30 s or less
or less482°F
446°F
302 to 356°F
t1 t2
0.3±0.05
Tractor feed holes
Direction of picking
7.2±0.1
1.75±0.1
1.55±0.05 dia.
2.8±0.3
Device mounted
on tape
5.5 ± 0.1
4.7
± 0.1
12±0.3
1.55±0.1 dia.
4±0.1
2±0.1
12±0.1
.012±.002
.284±.004
.069±.004
.061±.002 dia.
.110±.012
.217 ± .004
.185
± .004
.472±.012
.061±.004 dia.
.157±.004
.079±.004
.472±.004
21±0.8
80±1 dia.
2±0.5
13±0.5 dia.
14±1.5 2±0.5
250±2 dia.
80±1 dia.
.827±.031
3.150±.039 dia.
.079±.020
.512±.020 dia.
.551±.059 .079±.020
9.843±.079 dia.
3.150±.039 dia.
Device mounted
on tape
Direction of picking
Tractor feed holes
1.5 dia.
1.55±0.1 dia.
±0.1
−0
±.004
−0
4±0.1
2±0.1
10.2±0.1
12±0.1
0.3±0.05
4.2±0.3
12±0.3
5.5±0.1
1.75±0.1
5.25±0.1
.059 dia.
.061±.004 dia.
.157±.004
.079±.004
.402±.004
.472±.004
.012±.002
.165±.012
.472±.012
.217±.004
.069±.004
.207±.004
80±1 dia.
13±0.5 dia.
21±0.8
17.5±2.0 2±0.5
2±0.5
300±2 dia.
80±1 dia.
3.150±.039 dia.
.512±.020 dia.
.827±.031
.689±.079 .079±.020
.079±.020
11.811±.079 dia.
3.150±.039 dia.
0.3±0.05
Tractor feed holes
Device mounted
on tape
Direction of picking
1.6±0.1 dia.
4.5±0.3
4±0.1
2±0.1
10.1±0.1
1.75±0.1
9.2±0.1
12±0.1
7.5±0.1
16±0.3
1.5
+0.1
−0
+.004
−0
.063±.004 dia.
.177±.012
.157±.004
.079±.004
.400±.004
.069±.004
.362±.004
.472±.004
.295±.004
.630±.012
.012±.002
.059
dia.
dia.