Split Type Inverter Room Air Conditioner OPERATION MANUAL MODELS AY-X28MCJ AE-X28MCJ Thank you for selecting SHARP air-conditioner. Please read this manual carefully before operation and keep it for further reference.
Names and functions of each part Operation of remote control and cleaning ing ing Check after installation and Test operation Specifications NOTE:All the pictures in this manual are just schematic diagrams. The actual product is the standard. that should be prevented. that Collection of such waste should be separated for special treatment as required by local regulations.
1.
, pl ease ref er the mat ter to a qualified air conditioner contractor. objects Don’t expose yoursel f to col d output air for prolonged periods as it may affect your physical condition. To change the airflow direction, adjust the vertical and lateral air flow direction by using the remote control. Don’t expose animals and plants directly to the output air flow as it may have a detrimental effect on them. This air conditioner is designed for normal residential use.
Air conditioners absorb heat in the room and transmits it to the outdoor unit, so that indoor ambient temperatures are decreased. Its cooling capacity will increase or decrease according to outdoor ambient temperature. If the unit is running in COOL mode and in low ambient temperature, frost may be formed on the heat exchanger. When indoor heater exchanger temperature decreases below zero, the indoor unit microcomputer will stop the compressor running to protect the unit.
Names and functions of each part Indoor unit ˄ ˅ Air in ˄ ˅ (3) ˄ ˅ Air out ˄ ˅ ˄ ˅ Ł Front panel ł Filter Ń Guide louver ń Wall pipe Ņ Bind tape Outdoor unit ņ Connection wire Ň Drainage pipe ň Remote control Air in (6) ˄ ˅ Air out 4
Operation of remote control Names and functions of remote control buttons Note: Be sure that there are no obstructions between receiver and remote control; Don't drop or throw the remote control; Don't let any liquid in the remote control and put the remote control directly under the sunlight or any place where is very hot. (ˇ/ˉ) Signal transmitter Ɣ FAN AUTO OPER X-FAN HUMIDITY FILTER TURBO HOUR TEMP. (ˇ/ˉ) button Press + button to increase the temperature by 1C o.
Operation of remote control Names and functions of remote control buttons NOTE: This wireless remote control is universal and it could be used for many different models.Some buttons on this remote control are not applicable to this model. FAN TIMER AUTO OPER X-FAN HUMIDITY Ɣ FILTER TURBO HOUR ON/OFF ON/OFF Remote control MODE FAN X-FAN TURBO TURBO TIMER SLEEP LIGHT Turbo button Under cool or heat mode, pressing this button turns on or off the Turbo feature.
Operation of remote control Names and functions of remote control buttons NOTE: This wireless remote control is universal and it could be used for many different models. Some buttons on this remote control are not applicable to this model. X-FAN Ɣ FAN AUTO OPER X-FAN HUMIDITY FILTER TURBO HOUR ON/OFF Remote control ON/OFF X-FAN button Press this button to select or cancel X-FAN mode. X-FAN off is the default setting when the unit is switched on.
2SHUDWLRQ RI UHPRWH FRQWURO *XLGH IRU RSHUDWLRQ JHQHUDO RSHUDWLRQ 3UHVV 21 2)) EXWWRQ WR WXUQ WKH XQLW RQ 1RWH 3ULRU WR WXUQLQJ RQ WKH ELJ JXLGH ORXYHU DQG VPDOO JXLGH ORXYHU ZLOO EH FORVHG 02'( 21 2)) 3UHVV 02'( EXWWRQ WR VHOHFW GHVLUHG UXQQLQJ PRGH 3UHVV EXWWRQ WR VHW WKH GHVLUHG WHPSHUDWXUH )$1 ,W LV XQQHFHVVDU\ WR VHW WKH WHPSHUDWXUH DW $872 PRGH 3UHVV WKH )$1 EXWWRQ WR VHOHFW WKH IDQ VSHHG 6HOHFW EHWZHHQ $872 )$1 /2: 0,' RU +,*+ ; )$1 785%2 7,0(5 6/((3 /,*+7 3UH
Operation of remote control ƾ $ERXW $872 581 When AUTO RUN is selected, the set temperature will not be displayed on the LCD. The unit senses the room temperature automatically to select a suitable running method for room comfort. ƾ $ERXW WXUER IXQFWLRQ When TURBO mode is selected the unit will run at super-high fan speed to cool or heat quickly so that the ambient temperature approaches the preset temperature as soon as possible.
on the main unit. Operation will be in Auto Run mode and the temperature setting or fan speed cannot be changed. To operate: Press the AUTO/STOP button and the unit will enter into AUTO RUN mode. The microcomputer will monitor the room temperature to select the (COOL, HEAT, FAN) mode automatically, to obtain the comfortable effect. To turn off: Press the AUTO/STOP button to switch the unit off.
Care and Cleaning to prevent at the circuit breaker the risk of electric shock. pour or spray liquids directly onto the indoor or outdoor units for cleaning, to prevent risk of electric shock. Only wipe the Rotate the front panel upwards in the direction of the arrow. While holding both sides of the front panel, remove by pulling forwards. Some minor force may be required. Before cleaning, remove the LCD display (if fitted) from the front panel.
Care and Cleaning Removing Rotate the front panel upwards in the direction of the arrow. Pull the air filter downwards and remove from the unit. water temperature should be and leave to dry naturally in a shady location. Never dry it with a heater or open flame, as fire or deformation may occur. in the di rec tion of the ar rows, then cl os e the front panel. Never operate the unit if the wiring or connections have been damaged. report to a licenced contractor.
The air conditioner is not user serviceable. if attempt to If a bad smell has been accumulated from the environment, clean the air filter. If smells persist, contact your Approved Service Centre to arrange cleaning. fluid gurgling noises. This is not a fault - it is the sound of flowi ng refrigerant.
will Has the circuit breaker device tripped off? Have the wiring or connections been damaged?Please report to an authorised air conditioner contractor. Is the fan other working Check that there is no magnetic or electrical interference near the main unit that may be affecting the operation of the controller. Is the wireless remote control within its operating range, or obstructed? Check the condition of the batteries and replace if necessary. Check if the wireless remote control is damaged.
air flow is stopped fros t can be for med on the outdoor heat exchanger. The unit will automatically defrost and the indoor unit will stop blowing air for 3-12 mins. During defrost operation, water or vapour may be emitted. ,disconnect from the power supply, and report to an authorised air conditioner contractor in the following situations. St rong odours are emi tted Circuit breaker continuously trips off. Water has dripped into or been splashed onto the unit.
The unit must only be installed by authorised air conditioner contractors according to municipal or government regulations and in compliance wi th this manual. The unit should be installed with a dedicated electrical circuit, and a circuit breaker should be fitted in accordance with regulations. Proper installation position is vital for correct and efficient operation. Avoid the following positions: liquids electro-magnetic Where salt-laden air is a problem (such as close to coastal areas).
A dedicated power supply circuit should be used, in accordance with local electrical safety regulations. The product should be installed by a licenced air conditioning contractor in accordance with AS/NZS3000 and your electrical supplier's rules. A circuit breaker should be installed. WARNING: inadequate or incorrect electrical connections may cause electrocution or fire. . P lease ensure the the unit is reliably earthed. the air conditioner is the earthing wire, and cannot be used for any other purpose.
Installation dimension diagram Installation dimension diagram 15 cm Space to the ceiling Above 15cm Above 15cm Above Space to the wall Space to the wall 300 cm 2 230 cm Above Above Air outlet side Air inlet side cm Ab ov e Space to the obstruction 50cm Above Space to the floor 30 30cm Above Ab ov e 50cm Above 20 0c m Space to the wall Air outlet side 18
,QVWDOO LQGRRU XQLW ,QVWDOO WKH UHDU SDQHO $OZD\V PRXQW WKH UHDU SDQHO KRUL]RQWDOO\ and leveled to ensure correct drainage.
Installing the indoor unit All interconnecting wiring between indoor and outdoor unit must be performed by a licenced electrical contractor in accordance with AS/NZS3000. the unit to screws adequately to prevent loosening. Ensure the electrical connections are properly earthed to prevent electrical shocks. Ensure all wiring connections are secure and the cover plates are reinstalled properly. Poor installations that allow dust or moisture incursion may cause fire or electrocution.
Installing the Outdoor Unit Connect Outdoor electric wires Remove electrical connection access plate (either right hand side or front) from the outdoor unit. Replace access plate (either right hand side or front) on the outdoor unit. Incorrect unit failure.
Installing the Outdoor Unit soapy gas detection are leaking. Outdoor attach satisfactorily.
satisfactory to the product. product. Are the inlet and outlet air openings blocked? Is the quantity of gas charge sufficient for the length of pipe run? may be insufficient.
Specifications Model AY-X28MCJ; AE-X28MCJ Function COOLING Rated Voltage HEATING 220-240 V Rated Frequency 50Hz Total Capacity (Min̚Max) (W) 8000(2100̚8400) 8400(1800̚9300) Power Input (Min̚Max) (W) 2660(650̚3200) 2860(600̚3500) 3500 Rated Input (W) Rated Current (A) 15.53 3 Air Flow Volume (m /h) (SH/H/M/L/SL) -/1200/1100/1000/- Dehumidifying Volume (L/h) 2.7 EER / C.O.P (W/W) 3/2.
Outdoor Compressor Unit Manufacturer/trademark MITSUBISHI Compressor Model TNB220FLHMC Compressor Type Rotary L.R.A. (A) 45 Compressor RLA(A) 9.7 Compressor Power Input(W) 2200 Overload Protector CS01F272H01 Throttling Method Capillary Defrosting Method Automatic Defrosting Operation temp Range (ć) -7嘙C̚43嘙C Condenser Aluminum fin-copper tube Rows-Fin Gap(mm) 2 -1.4 Coil Length (LXDXW) 953.5X38.
:$55$17< $LU &RQGLWLRQHUV 6KDUS &RUSRUDWLRQ RI $XVWUDOLD 3W\ /WG JXDUDQWHHV WKDW VKRXOG D GHIHFW LQ WKLV SURGXFW GXH WR HLWKHU )$8/7< 0$7(5,$/6 RU :25.
SHARP FOR LOCATION ENQUIRIES WITHIN AUSTRALIA REGARDING YOUR LOCAL SHARP APPROVED SERVICE CENTRE VISIT OUR WEBSITE AT www.sharp.net.au OR CALL SHARP CUSTOMER CARE 1300 135 022 (LOCAL CALL COST APPLY WITHIN AUSTRALIA) SHARP CORPORATION OF AUSTRALIA PTY LTD SHARP FOR LOCATION ENQUIRIES WITHIN NEW ZEALAND REGARDING YOUR LOCAL SHARP APPROVED SERVICE CENTRE VISIT OUR WEBSITE AT www.sharp.net.
SHARP CORPORATION OF AUSTRALIA PTY LTD ABN 40 003 039 405 1 Huntingwood Drive HUNTINGWOOD NSW 2148 www.sharp.net.