PN-L601B Operation-Manual Setup-Guide GB FR DE

4
E
MOUNTING PRECAUTIONS
• Thisproductisforuseindoors.
• Sincethemonitorisheavy,consultyourdealerbeforeinstalling,
removing or moving the monitor.
• Wheninstalling,removingormovingthemonitor,ensurethatthis
is carried out by at least 2 people.
• AmountingbracketcompliantwithVESAspecicationsisrequired.
Do not use any screw holes other than VESA holes for installation.
• To attach a VESA-compliant mounting bracket, use M6 screws that
are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the thickness
of the mounting bracket.
• Whenmovingthemonitor,besuretoholditwitheitherbothhandles
or the 4 corners on the bottom of the unit. Do not place your hand
on the screen. This may cause product damage, failure, or injury.
• Installthemonitorwiththesurfaceperpendiculartoalevelsurface.
• Mountingthemonitoronthewallrequiresspecialexpertiseand
the work must be performed by an authorized SHARP dealer. You
should never attempt to perform any of this work yourself. Our
company will bear no responsibility for accidents or injuries caused
by improper mounting or mishandling.
• Thismonitorshouldbeusedatanambienttemperaturebetween
41°F (5°C) and 95°F (35°C). Provide enough space around the
monitor to prevent heat from accumulating inside.
For the monitor in horizontal orientation
7-7/8 [20]
Unit: inch [cm]
2 [5]
2
[5]
2
[5]
For the monitor in vertical orientation
Unit: inch [cm]
2 [5]
2
[5]
2
[5]
7-7/8 [20]
1-7/16 [3.5]
1-13/16 [4.5]
• Ifitisdifficulttoprovidesufficientspaceforanyreasonsuchas
the installation of the monitor inside a housing, or if the ambient
temperature may be outside of the range of 41°F (5°C) to 95°F
(35°C), install a fan or take other measures to keep the ambient
temperature within the required range.
• Temperatureconditionmaychangewhenusingthedisplay
together with the optional equipments recommended by SHARP. In
such cases, please check the temperature condition specified by
the optional equipments.
• Adheretothefollowingwheninstallingthemonitorinitsvertical
orientation. Failing to adhere to the following may cause
malfunctions.
- Install the monitor such that the power LED is located on the
bottom side.
- Set the MONITOR on the SETUP menu to PORTRAIT.
(See Operation manual.)
-Besuretoclampthepowercord(supplied)ontothecable
clampattachmentbelowusingthesuppliedcableclamp.When
clamping the power cord, take care not to stress the terminal of
the power cord. Do not bend the power cord excessively.
Power cord (Supplied)
Cable clamp
Cable clamp attachment
• Donotblockanyventilationopenings.Ifthetemperatureinsidethe
monitor rises, this could lead to a malfunction.
• Aftermounting,pleasecarefullyensurethemonitorissecure,and
not able to come loose from the wall or mount.
• Donotplacethemonitoronadevicewhichgeneratesheat.
• Usethesuppliedverticalstickerwhenyouinstallthemonitorin
vertical orientation.
Operation panel
Logo
Donotremovethefactory-afxedstickerbutafxthelogosticker
overit.Becarefulnottocovertheremotecontrolsensororbuttons.
• Besuretouseawall-mountbracketdesignedordesignatedfor
mounting the monitor.
• Thismonitorisdesignedtobeinstalledonaconcretewallorpillar.
Reinforced work might be necessary for some materials such as
plaster / thin plastic board / wood before starting installation.
This monitor and bracket must be installed on a wall which can
endure at least 4 times or more the weight of the monitor. Install by
the most suitable method for the material and the structure.
• Donotusetheproductinlocationswheretheunitisexposedto
direct sunlight or other strong light. Since this product operates
with infrared rays, such light may cause a malfunction.
■
Connecting the USB cable
Warning:
Contact your dealer or a service engineer to have the USB •
cable installed or removed.
Risk of electrical shock or injury if you attempt the work yourself.
• BeforeconnectingtheUSBcable,turnoffthemainpowerswitch
and disconnect the power cable from the outlet.
• UseonlythesuppliedUSBcable.
■
Installing the power switch
Warning:
Contact your dealer or a service engineer to have the power •
switch installed or removed.
Risk of electrical shock or injury if you attempt the work yourself.
1. Remove the screw (x1) from the monitor.
2. Remove the protective seal and connect the power switch
connector, making sure the connector is in the correct orientation.
3. Align the clamps with the slot in the bottom of the unit and tighten
the screws (x2).
 Makesurethattheclampsarermlysecured.
Take care that the cable is not caught or pinched.
4. Replace the screw that was removed in 1.
Bottom
Power switch
Mounting
bracket
Protective seal
Connector
Mounting
bracket