Operation Manual

43
E
Specifications
n
Product Specifications
Model PN-70HC1E
LCD component
70" Class [69-1/2 inch (176.6 cm) diagonal] TFT LCD
Max. resolution (pixels)
3840 x 2160
Max. colors
Approx. 1.07 billion colors
Pixel pitch
0.40075 mm (H) × 0.40075 mm (V)
Brightness (typical) 350 cd/m
2
*
1
Contrast ratio (typical) 4000: 1
Viewing angle
176°right/left/up/down(contrastratio≥10)
Screen active area inch (mm)
60-9/16 (W) x 34-1/16 (H) (1538.9 x 865.6)
Computer input signal
AnalogRGB(0.7Vp-p)[75Ω]
Sync signal
Horizontal/vertical separate (TTL: positive/negative)
Plug and play
VESA DDC2B
Input
terminals
Video Mini D-sub 15 pin, 3 rows x 2
HDMI x 3
AV RCA *
2
x 1
Component RCA *
2
x 1
Serial (RS-232C)
D-sub 9 pin x 1
Audio
3.5 mm mini stereo jack x 3
RCA pin (L/R) x 1
USB 2.0 compliant (Type A) x 4
2.0 compliant (Type A) x 2 (for Expansion slot)
Output
terminals
Video Mini D-sub 15 pin, 3 rows x 1
Audio
3.5 mm mini stereo jack x 1
Digital audio output (optical) x 1
System CPU Arm Cortex - A53 processor (quad core)
Memory 1.5GB
Storage 8GB
SD card slot SD/SDHC x 1
LAN terminal 10 BASE-T/100 BASE-TX (Wake on LAN only)
Wireless LAN IEEE802.11ac/n/a/g/b compliant (When a wireless adapter is connected)
Expansion slot 19 V, 4.74 A (power supplied when expanding the functions with an optional part)
Speaker output 10W+10W
Touch
Panel
Detection method Infrared blocking detection method
Computer connector USB (2.0 compliant) (Type B) x 2
Power requirement AC 100 - 240 V, 4.5 A, 50/60 Hz
Operating temperature
*
3
*
4
41°F to 95°F (5°C to 35°C)
Operating humidity
*
4
20% to 80% (no condensation)
Power consumption
*
5
(standby mode
*
6
)
400 W (0.5 W)
Dimensions inch (mm)
(excluding protrusions)
Approx. 64-1/8 (W) x 3-15/16 (D) x 39 (H) (1629 x 100 x 990)
Weight lbs. (kg)
Approx. 119.0 (54)
*1 Brightness will depend on input mode and other picture settings. Brightness level will decrease over time. Due to the nature of the
equipment, it is not possible to precisely maintain a constant level of brightness. This is the brightness of the LCD panel, not the
brightness of the product.
*2 AV RCA and Component RCA cannot be used simultaneously.
*3 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specified by the optional equipments.
*4 In addition, check the requirements of the computer and other devices to be connected, and make sure that all requirements are satisfied.
*5 When an option is installed in the expansion slot. When not installed, 295 W.
*6 When Power Save Mode is set to On.
When Power Save Mode is set to Off, and no optional part is attached: 2.0 W
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.