18P (5.
6 1
Notice for Users in the USA FCC Statement WARNING - FCC Regulations state that any unauthorized changes or modifications to these equipments not expressly approved by the manufacturer could void the user’s authority to operate these equipments. Note: These equipments have been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
For Wireless LAN Bundled Model Wireless LAN Model Name: T60H42400 FCC ID: MCLT60H42400 This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.
CAUTION: TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD AND THE BATTERY BEFORE SERVICING. CAUTION: FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG AND THE BATTERY. VORSICHT: UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN UND DIE BATTERIE ÈNTFERNEN. ATTENTION: POUR UN ARRET TOTAL DU SYSTEME, DECONNECTEZ LA PRISE DE COURANT SECTEUR ET LA BATTERIE. VARNING: FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH TA UR BATTERIET.
Safety Precautions General • • Follow all cautions and instructions, which may be marked, on the computer. Except as described elsewhere in this manual, refer all servicing to qualified personnel.
• • • Do not drop the computer nor hit it with other equipment. Do not scratch the surface of the LCD screen. Turn off the computer and disconnect the AC power cord before cleaning. Battery Precautions CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS. Handling • • • • Never put the battery pack in a fire, as it could explode and cause injury.
Charging • Charge the battery pack only with the AC adapter included with your computer. Discharging • Do not use the battery pack for any purpose other than powering your computer. Storage • Store the battery pack in a cool and dry place. Never allow the temperature to exceed 60°C (140°F) during storage. • Recharge the stored battery pack after storage, before use.
Caution Your computer is integrated with a magnet on the right side of the display. Be sure to keep the magnetic cards or floppy disks away from the right side of your computer. Otherwise the data on the cards or floppy disks may be erased. This computer has a sensor on the right side of the keyboard which responses to the magnet. If you bring the magnet near the right side of the keyboard, the backlight is turned off, and the system may enter the standby or the hibernate mode depending on the setting.
About This Manual Notice Information in this manual is subject to change without notice and does not represent a commitment on the part of SHARP Corporation and its sales subsidiaries. SHARP Corporation and its sales subsidiaries shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
Recording Important Information For future reference, please record the following information in the spaces provided below. Model Number: Serial Number: Date of purchase: Dealer’s Name: Place of purchase: Password: The serial number is printed on a sticker located on the bottom of the computer.
Manual Conventions This manual uses a set of style conventions described below. Notes and Cautions are italicized with icons: A note icon informs you of a special technique or information that may help you perform a task or better understand a process. A caution icon alerts you to something that may cause problems or damage to hardware, software or data. Key Labels on the Keyboard, when referred to in the instructions, are shown in boldface: Press Enter to continue.
Table of Contents Notice for Users in the USA.......................................................................................i Safety Precautions ....................................................................................................iv About This Manual.................................................................................................viii Recording Important Information.............................................................................ix Manual Conventions........
Peripherals Using Peripherals ................................................................................................... 4-1 Optional External Floppy Disk Drive Unit ............................................................ 4-3 Optional External CD-ROM Drive Unit ................................................................ 4-6 Display ................................................................................................................. 4-11 Audio System ...........................
Appendixes Maintenance and Care ...........................................................................................
Overview of Computer Each number after an arrow indicates the page referring to the part. Actual appearance of your computer may be slightly different depending on the model.
Status Indicators Hard Disk Indicator Antenna Indicator Battery Indicator Power Indicator Never turn off the computer when the hard disk indicator is on. This may damage the data on the hard disk.
Rear Display Connector →4-12 Bottom Battery Pack→3-1 Reset Switch →2-3 RESET Speaker xvi Ventilation Openings→ iv
CHAPTER 1 Quick Setup 1 Your computer is designed and pre-configured for easy setup and use. This chapter describes the steps to set up your computer and operate it as quickly as possible. Read this chapter first. Installing Battery Pack Your computer is powered with either the battery pack or AC power source. See the next chapter for more information on the power sources. Before using your computer for the first time: 1. Place your computer upside down. 2.
3. Insert the battery pack into your computer by matching the notched parts of the battery to the projected parts on your computer. Projected Part 1 Projected Part Notched Part Notched Part 4. 1-2 Push the battery pack all the way until you hear the clicking sound.
5. Slide the battery stopper to the locked position ( ). 1 6. Turn over your computer and go to the next section.
Connecting to AC Power Source 1 1. Plug the AC adapter cable into the AC adapter jack on the right side of your computer. 2. Plug the AC power cord into the AC adapter. 3. Plug the AC power cord into a wall outlet. AC Adapter Jack AC Power Cord To Wall Outlet AC Adapter • Always use the AC adapter and the AC power cord included with your computer or the optional one (may not be available in some countries). Using other AC adapters and AC power cords may damage your computer.
4. Slide the display cover lock lever to the right until the display cover releases, and raise the cover. 1 Display Cover Lock Lever 5. Press the power button to turn on your computer. Power Button Power Indicator ) turns green, your When you turn on your computer, the power indicator ( computer goes through a self test to detect any problems, and Windows setup process starts. See the next page.
Setting Up Windows The steps in the setup process are as follows: 1 • • • • • • Configuring your location, language and keyboard type Configuring your time zone Accepting license agreement Naming your computer Creating an account Completing configuration To setup Windows, follow the instructions on the screen. See also the Windows manual. It takes approximately 10-15 minutes to complete the entire setup process. • Do not turn off your computer until completing Windows setup.
Properties Dialog Box in Windows In this manual, you will often see the expression “XXX Properties dialog box.” A dialog box is a window containing text boxes, check boxes, buttons, etc., with which you can send commands to Windows or other application programs. To open the properties dialog boxes, click start - Control Panel. The Control Panel has two types of views: Category view and Classic view.
Turning Off Your Computer When you’ve finished using your computer, turn it off with one of the following ways: • 1 • From the start menu 1. Click start – Turn Off Computer. 2. In the Turn off computer dialog box, click Turn Off. With the power button Before using this step, confirm that Shut down is selected in When I press the power button on my computer in Advanced tab of Power Options Properties dialog box. Close the cover to keep the screen and keyboard clean and protected.
CHAPTER 2 Basic Operations 2 This chapter describes the basic operations of your computer. Choosing Power Source You can use your computer with one of the following power sources: • AC power from a wall outlet Use AC power whenever possible; rely on the battery only when AC power is not available. • Rechargeable battery Your computer is equipped with a standard battery pack. You can also use an optional high capacity battery. See Chapter 3 for the battery information.
• When the battery is hot, the battery indicator may turn off and stay off until the battery becomes cool. • For more information on System standby/hibernate, see Chapter 3. Using AC Adapter When connected to a wall outlet, the AC adapter provides power for operation and charges the battery. The AC input voltage can range from 100 to 240 volts so that you can use your computer with the appropriate plug adapter.
Resetting System You may need to restart the system if your computer hangs up or a new hardware or software is installed. When a message appears after the installation, click OK, Yes, etc. to restart Windows. You can also restart Windows by clicking start - Turn Off Computer; then, Restart.
Using Glide Pad Your computer is equipped with an integrated pointing device called a glide pad. Using the glide pad, you can move the pointer, select an item from a menu, and perform other tasks in the same way you would with a mouse. 2 Glide Pad • Do not hit or scratch the surface of the glide pad with pointed objects (such as a ballpoint pen). • Do not operate the glide pad with a moist finger. This may cause the glide pad to operate incorrectly.
Click, Double-click, and Right-click To click or double-click, you can use the left button just like that of a mouse. Instead of clicking the left button, you can also just tap gently anywhere on the rectangular pad. For right-clicking, you must use the right button. If the interval between clicks is too long, the double-click will not function. Drag and Drop 2 You can move the items by using “drag and drop” below: 1. Position the pointer over the item you wish to move. 2.
Using Keyboard Your computer, equipped with the Windows Enhanced Keyboard, provides all the functionality of a full-sized desktop keyboard. Special Keys 2 Windows Key Opens the Windows start menu. This key functions the same as the start button on the screen. Application Key Opens short-cut menus for the specific items. This key functions the same as the right mouse button. System Function Keys Your keyboard contains the function keys labeled F1 through F12 for special actions.
Controlling Volume You can adjust the output volume of your computer with the following volume controls which interact with each other. With Keyboard Press Fn and F3 ( Press Fn and F4 ( ) keys simultaneously to decrease the output volume. ) keys simultaneously to increase the output volume. 2 These functions do not work in the MS-DOS mode. On Windows 1. Click start - Control Panel. 2. Click Sounds, Speech, and Audio Devices; then, Sounds and Audio Devices.
Any software containing audio function may also have its own volume control. Note that the volume controls discussed on the previous page and the software volume control will interact with each other. Adjusting Display 2 You can adjust the brightness, resolution, and number of colors of the internal LCD display for more comfortable viewing. Changing Brightness of Display Press Fn and F6 ( LCD display. Press Fn and F7 ( LCD display.
*1) Only 1024 x 768 dots appear even on the internal LCD screen of 1280 x 1024, or 2048 x 768 resolution. To see the hidden parts, move the mouse pointer to the parts and scroll it. To set 1280 x 1024, and 2048 x 768 resolution mode selectable, open the Display Properties dialog box, click Settings tab, then, Advanced button and uncheck Hide modes that this monitor cannot display of Monitor tab. (Only a member of the Computer administrators group can set the resolutions selectable.
Changing Wallpaper and Setting Screen Saver You can enjoy various desktop patterns or screen savers. Changing Wallpaper 2 1. In the Display Properties dialog box, select Desktop tab. 2. Select appropriate wallpaper in Background. 3. Click OK. Setting Screen Saver 1. In the Display Properties dialog box, select Screen Saver tab. 2. Select an appropriate screen saver in Screen saver and set time when screen saver starts. 3. Click OK.
Sharing Your Computer If you are sharing your computer with your colleagues or family members, set a user account for each person. Every user can choose their favorite desktop setting, web site lists, or make their own My Documents folder etc., and save them to their user accounts. When you turn on your computer, select your user account. Setting New User Account 1. Click start - Control Panel. 2. Click User Accounts. If Classic view is selected, double-click User Accounts icon. 3.
3. Select a new account to start Windows XP again. If you cannot see Switch User in Log Off Windows dialog box, click Change the way users log on or off string in User Accounts dialog box, and check Use Fast User Switching and click Apply Options. Setting Password to User Account 2 You can set a password to each user account to avoid unauthorized use of your computer. Once you set the password, you need to enter it when you log on to its account.
Changing Password 1. Follow the steps 1-2 on the previous section. 2. Select the account you want to change, if you log on to your computer as a member of the Computer administrators group. If you log on your computer with a limited account, go to the next step. (You cannot change the password of another user account.) 3. Select Change the password string or Change my password string. • If the password has not been set yet, Change the password or Change my password will not appear.
2 2-14
CHAPTER 3 Battery and Power Management This chapter explains how to manage your computer’s power effectively and use the battery pack. 3 In this section, you often see the expression “Power Options Properties dialog box”. To open the dialog box: 1. Click start - Control Panel. 2. Click Performance and Maintenance - Power Options in Category view or double-click Power Options icon in Classic view.
Charging Battery Pack 1. Connect the AC adapter to your computer. While the battery is being charged, the battery indicator lights orange. 2. When the battery is fully charged, the battery indicator turns green. Charging time may vary according to the status of your computer. • The battery indicator may turn off even while the battery is being charged. This is because the battery pack is hot, and the charging stops temporarily.
• The remaining operating time depends on the amount of the power you are consuming. If you are using the audio system, PC card slot, hard disk drive, or peripheral devices with your computer, it may consume more battery life. • If the actual remaining power in your battery is less than what Power Meter indicates, you should condition the battery pack as per the procedure on Conditioning Battery Pack section in this chapter.
On Windows, you can set the battery level for sounding an alarm and letting your computer go on System standby, System hibernate or shut down afterward. 3 1. In the Power Options Properties dialog box, select Alarms tab. 2. Set the battery level at which the alarms are activated. We recommend you set Critical battery alarm to 5 % or more and Low battery alarm to more than the value of Critical battery alarm. 3. Set the Alarm Action… to the appropriate settings. 4. Click OK twice. 5.
Changing Battery Pack to Optional High Capacity Battery Pack The capacity of a battery pack gradually decreases when used repeatedly (the deterioration rate depends on the operating environment). If the battery life becomes extremely short even after the conditioning, you should buy an optional high capacity battery pack (CE-BL25). When you replace the battery pack with the optional one: 1. Turn off your computer and disconnect the AC adapter from your computer. 2. 3.
5. Insert the high capacity battery pack into the computer by matching the notched parts of the battery to the projected parts of the computer. 3 High Capacity Battery Pack (CE-BL25) Checking Battery Level of High Capacity Battery Pack Follow the steps in Checking Battery Level in this chapter. Conditioning High Capacity Battery Pack Follow the steps in Conditioning Battery Pack in this chapter.
Power Management Power management saves electricity and extends battery life by controlling power supply to built-in devices. You can set the following power management properties on Windows. • • • Stopping power supply to the hard disk Stopping power supply to the display Using System standby/hibernate To open Power Options Properties dialog box, click start – Control Panel, and click Performance and Maintenance; then, Power Options. If Classic view is selected, double-click Power Options icon.
Using System Standby/Hibernate System standby/hibernate is a very useful power management tool. For example, after your computer has entered System standby mode, you can restart your computer more quickly when compared to a restart, after a normal shutdown operation. When your computer resumes from System standby/hibernate, the system restores the exact last state of your computer. In Windows, you can define System standby or System hibernate the system enters under what conditions.
Supporting System Hibernate If your battery becomes completely discharged during System standby, you will lose unsaved data and will need to reboot your computer. Therefore, if you are planning to leave your computer powered by battery for long periods of time, we recommend System hibernate. Confirm that System hibernate is supported with the following steps below. 1. 2. 3. 4. In the Power Options Properties dialog box, select Hibernate tab. Confirm Enable hibernation is checked. Click OK.
4. • Close the Control Panel window. You press the power button. The above functions if you perform the following: • 3 1. 2. In the Power Options Properties dialog box, select Advanced tab. Select Hibernate or Stand by in When I press the power button on my computer field. 3. 4. Click OK. Close the Control Panel window. You press Fn+F12( ). The above functions if you perform the following: 1. 2. In the Power Options Properties dialog box, select Advanced tab.
CHAPTER 4 Peripherals This chapter describes how to use peripheral devices with your computer. You can connect an optional floppy disk drive unit, an optional CD-ROM drive unit, a printer, an external monitor, a PC card, or other devices to your computer. To ensure proper use, be sure to read the instructions for each peripheral device before connecting it to your computer. Using Peripherals You can use the peripheral devices shown on the next page.
Peripheral Connection Overview External Monitor USB Device* 4 Headphone/ Audio Equipment USB Device* *Including the optional external floppy disk drive unit (CE-FD05) and the optional external CD-ROM drive unit (CE-CD05).
Optional External Floppy Disk Drive Unit You can use double-density (2DD) 720KB or high-density (2HD) 1.44MB floppy disks with the optional external floppy disk drive unit (CE-FD05). Connecting Optional External Floppy Disk Drive Unit • Do not place the floppy disk drive unit on its side or upside down. • Do not press on the floppy disk drive unit. It may damage the drive or cause malfunction. • Do not place the AC adapter on the floppy disk drive unit. It may cause the drive to malfunction.
Inserting Floppy Disk Hold the floppy disk with the arrow facing up, toward the drive. Slide the disk into the drive until it locks into place. Arrow Facing Up Indicator • Always insert a floppy disk straight into the floppy disk drive. • When inserting the disk, make sure it is not upside down. • Do not use excessive force when inserting the floppy disk. If you have difficulty inserting or removing disks, seek the assistance of an authorized service technician.
Formatting Floppy Disk 1. Make sure the floppy disk is not write-protected, and insert it into the floppy disk drive. 2. Click start - My Computer. 3. Right-click 3 ½ Floppy (A:) icon; then, click Format… from the pop-up menu. 4. Select the appropriate formatting options. 5. Click Start to start formatting. • When you format a floppy disk that already contains data, all of the data stored on the disk will be lost. • You cannot format a double-density (2DD) 720KB floppy disk.
Optional External CD-ROM Drive Unit A compact disc (CD) is a storage medium, with which you can read data, play music, install and run programs, etc. The optional external CD-ROM drive unit (CE-CD05) can be connected to either of the USB ports on your computer. CAUTION FOR LASER Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Connecting Optional External CD-ROM Drive Unit (CE-CD05) • Do not place the CD-ROM drive unit on its side or upside down. • Do not press on the CD-ROM drive unit. It may damage the drive or cause malfunction. • Do not place the AC adapter on the CD-ROM drive unit. It may cause the drive to malfunction. 1. Connect the core side connector of the USB cable included in the optional external CD-ROM drive unit to the cable connector of the drive unit. USB Cable Core 2.
3. Slide the cover latch to the right and open the cover. Cover Latch 4. Remove the protection sheet before you use the drive for the first time. Protection Sheet Laser Beam 4 Handling CD • Do not write on either side of the disk, particularly the non-label side. Data is read from the non-label side. Do not mark this surface. • • Keep your disks away from direct sunlight, heat and excessive moisture. Always hold the CDs by the edges.
3. Place your CD onto the disk spindle and press on the center of your CD with label side up, until it locks onto the disk spindle. L ABEL 4. Close the disk cover. • Insert a CD firmly until it is locked onto the spindle; then, close the disk cover, or the disk may fall off the spindle and get damaged. • Do not leave the tray open. Also, avoid touching the lens in the tray. If the lens becomes dirty, the CD-ROM may malfunction.
Playing CD With some CD-ROMs, you can hear the sound of them through the audio out jack of the CD-ROM drive unit. Connect headphones or speaker system with an amplifier to the audio out jack. Audio Out Jack Disconnecting Optional External CD-ROM Drive Unit To remove the unit, you need to perform the following steps before you remove it. 4 1. 2. 3. Click Safely Remove Hardware icon ( ) on the taskbar. Click Safely remove USB Mass Storage Device; then, Safe To Remove Hardware dialog appears.
Display You can use an external monitor with your computer. To display the images on both displays simultaneously, use the 1024x768 resolution. • Some monitors, which are not compatible with your computer, may not display correctly. • In this section, you often see the expression “Display Properties dialog box.” To open the dialog box, right-click somewhere on the Windows desktop and select Properties from the pop-up menu.
3. Connect the display converter cable to the display connector, then, the other end of the display cable to your external monitor. If the display cable has screws, be sure to tighten them. Display Connector Display Converter Cable Display Cable 4 4. Turn on the external monitor; then, your computer. Disconnecting External Monitor 1. 2. Turn off your computer and the external monitor. Press the button on the connector of the display converter cable, and hold it; then, remove it from your computer.
2. 3. Select Lynx3DM+ tab; then, click the button before the output display you desire and click OK. Click OK to close the Control Panel window. • You can also switch the display with Fn+F5 ( ). • When you log on your computer as a member of the Limited group, you cannot switch the display with the dialog box. Use Fn+F5( ) keys.
Audio System You can output sound to speakers, audio equipment or headphones. Connecting Speaker You can connect stereo speakers with an amplifier to the audio output jack on the left side of your computer. Speakers with an Amplifier Headphone/Audio Output Jack 4 Stereo Mini Plug Connecting Audio Equipment You can connect analog audio equipment to the audio output jack on the left side of your computer.
You can adjust the output volume on Windows by clicking the speaker symbol on the taskbar or use Fn + F3 ( ) or F4 ( ) keys combination. Connecting Headphone Use the headphone with an impedance of 8Ω.or more (32Ω is recommended.
USB Device Your computer has an interface called Universal Serial Bus (USB) and its two USB ports support USB1.1 and USB2.0. With a USB connection, you can connect/disconnect peripherals without turning off your computer. Generally, when you connect a device to your computer, the necessary driver will be installed automatically. See also the manuals of peripheral devices supporting USB. When a new device is correctly connected to your computer, the appropriate driver is automatically installed.
PC Card Your computer is equipped with a PC card (PCMCIA) slot, which can accommodate a Type II card or a CardBus compliant card. You can insert/eject the card without turning off your computer. Inserting PC Card When a new card is correctly inserted, the appropriate driver is automatically installed. If the driver is not installed correctly, you will see the message on the screen. In this case, install the PC card driver by following the instructions on the screen. 1.
4 2. Push the PC card eject button again until the protection card pops out, then remove it. 3. 4. Push the PC card eject button all the way inside the cabinet for safekeeping. Insert a PC card into the slot with the label face up until it locks into place. Label Face Up If the dialog box asking you What do you want Windows to do? appears, select the task you want. Ejecting PC Card • Some PC cards may become hot after long use. • Be sure to use the procedure below when ejecting a PC card.
3. Push the PC card eject button so that it will pop out from the side of your computer. 4. Push the eject button until the inserted PC card pops out; then, remove it. 4 5. Push the PC card eject button all the way inside the cabinet for safekeeping.
6. Insert the protection card. Be sure to insert the protection card after you finish using the PC card slot to protect the PC card slot from being damaged.
Printer You can connect a printer to either of the USB ports on your computer. Before using a printer, read the printer manual and install the printer driver. Connecting Printer Be sure to read the printer manual before connecting the USB printer to your computer. Some printers may not use Found New Hardware wizard to install the printer driver. You can connect the USB printer to your computer without turning off your computer.
4 4-22
CHAPTER 5 Communication Functions This chapter explains how to use the wired LAN unit, the wireless LAN function and the modem card. • When you use communication software: • Connect your computer to the AC power source. • Disable power management. (Refer to Disabling Power Management of Chapter 3.) • See also the manual or online help of the software you are using.
Connecting Your Computer To LAN 1. 2. Turn off your computer. Open the cover for the LAN jack on the right side of your computer. Cover To avoid damaging the LAN unit, close the cover after you finish using the LAN unit. 5 3. Connect one end of the LAN cable to the LAN jack and the other end to the network hub. LAN Jack To Network Hub LAN Cable 4. 5-2 Turn on your computer.
Configuring LAN Unit 1. Click start - Control Panel. 2. Click Network and Internet Connections; then, Network Connections. If Classic view is selected, double-click Network Connections icon. 3. Right-click Local Area Connection. 4. From the pop-up menu, click Properties. 5. In the Local Area Connection Properties dialog box, set the network setting according to the instruction of your network administrator. Make sure to log on your computer as a member of the Computer administrators group.
Wireless LAN Your computer has an integrated wireless LAN function compliant with IEEE 802.11b standard. You can access the network by the wireless LAN. There are two kinds of wireless networks: a network using an access point and an Adhoc network. You can connect your computer to a wired LAN or the Internet through an access point that is also compliant with IEEE 802.11b standard. The Adhoc network consists of a number of computers each equipped with wireless networking interface.
Connecting to Internet via an Access Point You can connect your computer to the Internet or a wired network via an access point supporting IEEE 802.11b. Refer to the manual of the access point or consult your network administrator if you are not sure. Communicating with Other Computers • Confirm each computer is enabled for wireless LAN. • Make sure to log on your computer as a member of the Computer administrators group. Otherwise, you cannot set or change some settings for wireless LAN. 1.
11. Configure the network by setting the name of your computer and workgroup. To communicate with other wireless enabled computers, set your computer name and the workgroup name. Your computer name should be unique and the workgroup name should be same as others. Confirming the Status of Wireless Connection Before performing the following instructions, confirm the devices that you want to communicate with are enabled for wireless LAN. 1. Click Wireless Network Connection icon ( or ) on the taskbar.
Connecting WEP configured network Wireless communication has security issues. Some networks are configured with WEP (Wired Equivalent Privacy) keys or encryption keys to protect the transmitted data. To connect into the WEP configured network, follow the steps below. 1. Right-click Wireless Network Connection icon ( View Available Wireless Networks. 2. Select the network you want to connect in Available wireless networks of Wireless Network Connection dialog box. 3.
Network Setup Utility With the Network Setup Utility, you can set up your specific network settings adjusted for your environments such as work, home, etc. and select the appropriate one to the environment. You can also change the network settings. • Not every setting item can be stored. • The Network Setup Utility may not compliant with all network environments.
Changing Network Settings To change the loaded network settings, right-click on the icon you want to change the settings in the Network Setup Utility window and click Edit settings in the pop-up menu. Then, edit the settings. Deleting Network To delete the loaded network settings, right-click on the icon you want to delete in the Network Setup Utility window and click Delete setting in the pop-up menu. Then, click OK.
Modem Card (may not be available in some countries) Your computer may come with the modem card. In order to use the modem on your computer, install the supplied modem card in your computer. • The modem in your computer is designed only for regular analog telephone lines. The modem may be damaged when connected to a digital ISDN terminal or a digital PBX. • Use TA (terminal adapter) to connect the built-in modem to a digital telephone line.
Connecting Modem To Telephone Line 1. 2. 3. Turn off your computer. Connect PC card connector end of the included modem cable to the connector of the inserted modem card. Connect the modular jack end of the modem cable to the telephone line. 4. Turn on your computer. Connect the modem to the telephone line directly. Do not use a distributor or allotter. Configuring Modem Configure your modem making the necessary adjustments as shown below.
Power Management To use communication software, you may have to disable power management. See Disabling Power Management of Chapter 3. • See also the manual or online help of the software you are using. • Within the communications software you are using, set the COM port of the built-in modem to COM3. • Do not enter System standby/hibernate while using communication software. • Before commencing with fax communication, it is recommended that you exit other application programs.
CHAPTER 6 Setup Utility This chapter describes how to run the Setup Utility to change settings on your computer. Running Setup Utility With the Setup Utility, you can customize the system configuration information, such as time and date, port assignments, or passwords. The information you have specified is saved in a special area called CMOS RAM, which the system reads every time you turn on your computer. Your computer is shipped from the factory with the appropriate setting of the Setup Utility.
Entering and Exiting Setup Utility 1. Turn on your computer. 2. When Press to enter SETUP appears, press F2. 3. Change to the desired settings. Refer to the next section. 4. Select Exit menu; then, press Enter. 5. Select one of the exit methods, and press Enter. 6. Confirm the message and press Enter again. The system restarts. When the Setup Utility is opened, power management does not work. Do not close the display cover. Changing Setting of Setup Utility To change the settings: 1.
Main Menu System Time defines the system time, using the format hour:minute:second (24-hour format). Use Tab key to move the cursor, and minus key or space bar to change numerals. System Date defines the system date, using the format month/day/year. Use Tab key to move the cursor, and minus key or space bar to change numerals. Hard Disk Type shows the type of the hard disk of your computer. Press Enter key to show the details.
Advanced Menu Internal Pointing Device enables or disables the built-in glide pad. Resolution Expansion defines whether the Setup Utility screen is expanded when the resolution is 640x480 or 800x600. Enabled means that the screen is expanded. Plug&Play O/S enables or disables plug & play function. PCI Configuration normally has to be as default Security Menu Set Supervisor Password defines the supervisor password (up to eight characters). See the next section about the supervisor password.
Your computer supports two different levels of password security: Supervisor password and User password. You cannot set a user password unless you have set a supervisor password. If you share your computer with others, we recommend that you set both the supervisor and the user password, and let others know the user password only.
5. Select Exit menu and confirm Exit Saving Changes is highlighted; then press Enter 6. Confirm Yes is highlighted and press Enter. The system restarts. Boot Menu Boot Sequence specifies where the system boots from. Press Enter to open the sub menu. The system boots from the drive at the top of the list. If the system cannot find the drive, it will boot from the second one; then, third one; then forth one.
CHAPTER 7 Connection Cradle This chapter describes how to use the connection cradle with your computer (hereafter called MM series). Using the connection cradle, you can connect MM series to another computer (hereafter called Host computer). • Never insert anything but the MM series inside the cradle. • Be sure to keep the inside of the connection cradle free from dust or any foreign objects. This may cause malfunction and bad connection. Especially keep the connector clean.
Installing Application Program You cannot install an application program to the MM series from the host computer when the MM series is inserted in the cradle. In order to install an application program into the MM series, do either of the following performance: • Connect the external CD drive unit to the MM series • Connect the MM series to the host computer via LAN and share the CD drive of the host computer with the MM series.
Setting Up Connection Cradle 1. Attach the stand plate to the connection cradle matching the projection on the bottom panel of the connection cradle with the hole of the stand plate. Hole Stand Plate Connection Cradle Bottom 2. Projection Tighten two screws to fasten the stand plate to the connection cradle.
Overview of Connection Cradle Front Panel READY Lamp Hard Disk Lamp Battery Indicator Host PC Connection Switch REA DY OF F HD D ON Rear Panel USB Port 7 AC Adapter Jack Charging Battery Pack Using Connection Cradle 1. Set the connection cradle on a stable and even work surface. Be sure to attach the stand plate to the connection cradle before inserting the MM series into the connection cradle. Otherwise they may fall down. 2. 7-4 Connect the AC power cord to the AC adapter.
3. Plug the AC adapter cable to the AC adapter jack on the rear side of the connection cradle. 4. Plug the AC power cord to the wall outlet. Always use the AC adapter and the AC power cord included with your computer or the optional one. Using others may damage to the connection cradle. 5. Make sure that foreign materials such as dust are inside the connection cradle. Do not install the MM series in the connection cradle with foreign body, such as dust, inside.
Using MM Series as External Hard Disk Using the connection cradle, you can use MM series as an external hard disk of your host computer. Ordinarily, you can utilize the data between the mobile PC and the host PC via LAN or using the medium such as a memory card. By using the connection cradle, however, you can read /modify/save data stored in MM series without powered on.
Connecting to Host Computer MM series can be used as an external hard disk of the computer with one of the following operation systems installed: • Microsoft Windows XP Home Edition/ Microsoft Windows XP Professional (hereafter called Windows XP) • • Microsoft Windows 2000 Professional (hereafter called Windows 2000) Microsoft Windows Millennium Edition (hereafter called Windows Me) Before connecting the MM series to the host computer for the first time, be sure to install the connection cradle program
Connecting MM Series To Host Computer The following shows how to connect the MM series to the host computer for the first time using the connection cradle. Do not connect the USB cable until instructed to do so (in Step5 below). 1. 2. 3. 4. Install the Connection Cradle program to the host computer (shown on the previous page). Turn off the MM series. You cannot connect the MM series to the host computer when the MM series is powered on or in the standby/hibernate mode.
6. Slide the host PC connection switch on the connection cradle to the ON position. The READY indicator on the connection cradle turned green. When you connect the connection cradle to the host computer for the first time, necessary drivers are automatically installed. Wait until installation process completes. Y AD RE D HD ON OFF When the host computer runs on Windows XP, you might get the screen asking you what you want Windows to do. In this case, click Cancel.
The drive names such as (E:) and (F:) differs depending on the environment of the host computer. If you set a user password to MM series in the Setup Utility, MM series is shown not as hard disk drive, but as removable disk drive with the icon representing the MM series inserted in the connection cradle with the key mark. In order to access to the hard disk of your computer, delete the password temporarily. See Canceling Password in Password section later in this chapter.
Stopping Connection from Host Computer You can stop the connection from the host computer while keeping MM series inserted in the connection cradle, by first stopping the device on the host computer then sliding the host PC connection switch of the connection cradle to OFF. ` Be sure to stop the device before sliding the switch on the connection cradle to OFF. Otherwise the data may be lost or to the MM series may be damaged.
Connecting to Host Computer Again While you keep MM series inserted in the connection cradle, slide the connection switch back to ON to connect to the host computer again. When you do not remove MM series from the connection cradle after stopping the device, the connection is stopped, although the READY indicator is on. To regain the connection, slide the host PC connection switch to OFF, then back ON again.
Setting Password You can set a “user password” to your computer to avoid unauthorized use of the hard disk of the MM series when connected to the host computer using the connection cradle. Set the Supervisor password and User Password in the SetupUtility . Setting Password Set a user password of the MM series in the Setup Utility. For setting the password, see Chapter 6. Canceling Password Cancel the password temporarily when you want to use the MM series as an external hard disk of your host computer. 1.
In case of Windows Me When the host computer is Windows Me, cancel the password on the host computer, before deleting the user password in the Setup Utility of the MM series. 1. Cancel the password. 2. Stop the device. 3. Remove your computer from the connection cradle. Run the Setup Utility on MM series and delete the user password. For details on deleting the password, see Chapter 6. Be sure to cancel the password using Password Utility (see the previous page) before deleting the password.
Appendixes The appendixes contain additional information on the use and care of your computer. Maintenance and Care This appendix provides you with information on how to maintain your computer in excellent working condition. Cleaning Your Computer Cabinet Apply a small amount of mild cleaning solution to a dry, lint-free cloth and wipe the cabinet with the cloth. Screen The surface of the screen may become smeared and accumulate dust during use.
• Do not carry your computer powered on. This may result in loss of data and/or damage to the hard disk drive. • Make sure the display cover is closed before traveling. Otherwise, the cover may be opened unawares, and the display or the keyboard will be damaged. • If you carry your computer in a bag, try to avoid unnecessary pressure, caused by the stuff of the bag, to your computer. • • Disconnect the AC adapter from your computer. • Avoid sudden shocks or extreme vibration.
Troubleshooting This chapter describes how to troubleshoot computer problems. Common Problems Problems with your computer can be caused by something as minor as an unplugged power cord or as major as a damaged hard disk drive. The information in this troubleshooting section is designed to help you find and solve minor problems. If you still have a problem after trying all the suggested remedies in this chapter, contact your dealer.
Trouble when Starting Question: Why doesn't the power indicator or the battery indicator turn on? • Make sure the AC adapter is correctly connected to the AC adapter jack of your computer. • Make sure the AC power cable is correctly connected to a live wall outlet. Connect another electric equipment to the wall outlet and check whether it is live or not. • • Make sure the battery pack is correctly installed and charged. If the battery pack is discharged, connect the AC adapter.
Trouble with Display See the Display section in Chapter 2 and 4. Question: Why is the screen blank? • Press any key to see if any power management feature has turned off the screen to save power. • • See the power indicator to check whether your computer is turned on. • • • Make sure the LCD screen is selected as the display by pressing Fn+F5. If you are using a battery pack, make sure it is correctly installed and has a charge remaining. Check whether the display is on by pressing Fn+F11.
• When you select Extended Desktop mode, Fn+F5 key combination does not work. Trouble with Keyboard/Glide Pad Question: Why doesn't the keyboard or the glide pad function? • Try the following in this order: 1. Press Ctrl+Alt+Delete and select Users tab of Windows Task Manager dialog box. Click Disconnect or Logoff; then, Yes. 2. If the step 1 fails to work, press the power switch for more than four seconds to turn off the system. Ten seconds later, turn on your computer. 3.
Trouble with Hard Disk Question: Why can't I read or write data to/from the hard disk? • • Confirm the drive and file names are correct. Confirm the hard disk has sufficient free space. Trouble with CD Question: Why can’t I read data from a compact disc or play files? • • • • • Confirm the external CD-ROM drive unit is correctly connected to your computer. Confirm the CD is inserted correctly. Confirm the drive and file names are correct. Confirm the CD is not stained or scratched.
Question: Why can't I access the LAN? • • • Confirm the cable is properly connected to the LAN jack and the network hub. • Confirm the user name or password is correct. Confirm the network configuration is appropriate. Confirm the LAN driver is enabled in System Properties dialog box. Click Hardware tab, then, Device Manager. Double-click Network adapters, then, Realltek RTL8139xxxxx, and confirm Use this device (enable) is selected in Device Usage field of General tab.
• When you have more than one available access points, your computer may be connected to the access point other than the one you want to access: ) on the taskbar; then, click 1. Right-click Wireless Network Connection icon ( View Available Wireless Networks. 2. Select the desired network in the Available wireless networks list; then, connect to the network. (Refer to Confirming the Status of the Wireless Connection section in Chapter 5.
to connect again. (The distance between computers or access points should be less than approximately 190 ft. (60 m) in the direct line-of-sight.) • • Confirm the IP address and the subnet mask of each computer are set correctly. Confirm the WEP key is correctly entered if the WEP security of other devices, which you want to communicate with, is enabled. Trouble with Peripherals Question: Why don't peripheral devices function correctly? • • • • Confirm they are correctly connected to your computer.
Other Troubles Question: Why is the battery pack discharged so quickly? • Condition the battery pack. (Refer to Conditioning the Battery Pack section of Chapter 3.) Question: Why is the date and/or time incorrect? • Correct the date and time in Windows. Double-click the time appearing on the taskbar and set them in Date and Time Properties dialog box. Question: Why can't I use a hardware device? • Make sure the hardware device is not crossed out with an X mark using the following procedure. 1.
Question: Why can’t find the drivers and applications? • You may accidentally remove them. They are stored on the last recovery disk. (i.e. when two recovery CDs are provided, they are stored on the “Disk 2”.) When you are not sure how to install them or the CD does not have the drivers or applications, consult local service staff.
hibernate mode. Be sure to turn off the MM series before setting it into the connection cradle. • Once you stop the device on the host computer with the MM series in the connection cradle, it is not recognized as an external hard disk. Slide the host PC connection switch once to OFF, then back again to ON. • Make sure that the operating system of the host computer is Windows XP, Windows 2000, or Windows Me.
T-12
Index AC adapter connecting, 1-4 using, 2-2 Account creating, 2-11 switching, 2-11 Antenna, 5-4 Audio controlling output volume, 2-7 B Battery pack changing, 3-5 charging, 3-2 checking level, 3-2 conditioning, 3-4 indicator, 2-1 3-3 low battery indication, 3-3 C Cleaning computer, A-1 CD handling, 4-8 inserting, 4-8 removing, 4-9 troubleshooting, T-5 CD-ROM drive (external) connecting, 4-7 mode switch, 4-10 removing, 4-9 Connection Cradle charging battery, 7-4 connecting to hostcomputer, 7-8 overview, 7-
G Glide pad changing configuration, 2-5 clicking and double-clicking, 2-5 drag and drop, 2-5 scroll, 2-5 troubleshooting, T-4 H Hard disk drive troubleshooting, T-5 I Indicators antenna,5-4 power,1-5, 2-1 battery status, 2-1,3-3 status, xv K Keyboard function keys, 2-6 special keys, 2-6 troubleshooting, T-4 windows key, 2-6 L Index LAN configuring, 5-3 connecting to wired network, 5-2 troubleshooting, T-6 N Network Setup Utility changing, 5-9 deleting, 5-9 loading, 5-8 switching, 5-8 Index-2 P Passw
generating conditions, 3-9 resuming from, 3-8 System hibernate about, 3-8 generating conditions, 3-9 resuming from, 3-8 supporting, 3-9 Status indicators, xv T Troubleshooting common problems, T-1 communications, T-5 CD, T-5 Connection Cradle, T-10 display, T-3 floppy disk drive, T-4 hard disk drive, T-5 keyboard or glide pad, T-4 peripherals, T-8 wired LAN, T-6 wireless LAN, T-6 U USB device, 4-16 W Index Wallpaper, 2-10 Wireless LAN activating antenna, 2-6, 5-4 communicating, 5-5 confirming status,5-
Index Index-2
118P (5.
