User`s manual

3-14
ZM-30 (ZM-61E) ZM-
**
(ZM-62E)
Model
Item
Sampling
(Trend)
Count value is displayed
only at ZM.
Count of the zero position
is displayed at the lower
left area of the graph.
Numeric values [Display Function: Sample Count Display],
[Digits: 3] and [Char. Type: 1/4] are set at the lower left
area of the graph.
The current count is displayed.
Sampling
(bit)
A space of 1-byte chara-
cter size is provided
between the display in the
area and the message.
A space of four 1-byte character size is provided between
the display in the area and the message.
Memory card
mode
Card No.
/Card name
/File name
/Record name edit
Edited and entered No./
name are once stored in
the PLC memory.
Card No.
/Card name
/File name
/Record name edit
Impossible
Since No./name is directly written in the memory card,
nothing is stored in the PLC memory.
Switch [Action]
• [File Select]
• [Record Select]
• [Selection Complete]
To select a file/record in
the card, follow either of
the procedures below.
[File Select] -> (1)
[Selection Complete] ->
(2) [Selection Complete],
or [Record Select] ->
[Selection Complete]
Switch [Function]
-> [File Select]
-> [Record Select]
-> (None)
To select a file/record in the card, follow either of the
procedures below.
[File Select] -> (1)(2) (Press the display area)
[File Select] -> [Record Select] -> (Press the display area)
The operation “press the display area” is used instead of
pressing the [Selection Complete] at ZM-30 (ZM-61E).
Card No. 0
File No.
Card Name Hak
File Name
File No. 3
File Name TU-008
File Select
Rec Select
Card No. 0
Card Name Hak
File Select
Rec Select
Sel Finish
0. Produce
1. Target
2. SR-003
3. TU-008
Sel Finish
0. TUA
1. TUB
2. TUC
3. TUD
4. TUE
5. TUF
6. TUG
Card No. 0
File No.
Card Name Hak
File Name
0. Produce
1. Target
2. SR-003
3. TU-008
0. TUA
1. TUB
2. TUC
3. TUD
4. TUE
5. TUF
6. TUG
File No. 3
File Name TU-008
File Select
Rec Select
Card No. 0
Card Name Hak
File Select
Rec Select
Switch [Action]
• [File Name Edit]
• [Record Name Edit]
Press [File Name Edit] or
[Record Name Edit] after
selecting a file or a re-
cord, and the multi-over-
lap for which the chara-
cter entry mode is set is
displayed.
Switch [Function]
-> [File Name Edit]
-> [Record Name Edit]
Select a file or a record after turning ON the [File Name
Edit] or [Record Name Edit] switch, and the multi-overlap
for which the entry mode is set is displayed.
Record Select
0. Produce
1. Target
2. SR-003
Rec Name Edit
BCDA
FGHE
0. TUA
1. TUB
2. TUC
Record Name TUA
Record Select
Rec Name Edit
Blinking
Record No. 0
Record Name TUA
0. TUA
1. TUB
2. TUC
3. TUD
4. TUE
5. TUF
6. TUG
File Name Edit
Rec Name Edit
Record No. 0
Record Name TUA
0. TUA
1. TUB
2. TUC
3. TUD
4. TUE
5. TUF
6. TUG
File Name Edit
Rec Name Edit
BCDA
FGHE
Record Name TUA
CR
CR
3 ZM-61E -> ZM-62E Conversion