MX-M350U/N/M450U/N Operation-Manual Scanner GB
Table Of Contents
- INTRODUCTION
- TABLE OF CONTENTS
- ABOUT THE NETWORK SCANNER FUNCTION
- SETTINGS AND PROGRAMMING REQUIRED FOR THE NETWORK SCANNER FEATURE
- ACCESSING WEB PAGES
- ABOUT THE WEB PAGES (FOR USERS)
- ABOUT THE WEB PAGES (FOR THE ADMINISTRATOR)
- BASIC SETTINGS FOR NETWORK SCANNING
- SETTING UP DESTINATION INFORMATION
- STORING SENDER INFORMATION (Scan to E-mail)
- SETTING UP INTERNET-FAX PARAMETERS
- SETTING UP SERVERS
- PROTECTING INFORMATION PROGRAMMED IN THE WEB PAGE ("Passwords")
- BASE SCREEN
- SENDING AN IMAGE
- DESTINATION INPUT METHODS
- SCANNING SETTINGS (ORIGINAL SIZE, EXPOSURE, RESOLUTION AND FILE FORMAT)
- SPECIAL MODES
- PROGRAMMING FREQUENTLY USED OPERATIONS (PROGRAM)
- ERASING EDGE SHADOWS (ERASE)
- TRANSMITTING A DIVIDED ORIGINAL (DUAL PAGE SCAN)
- AUTOMATIC TRANSMISSION AT A SPECIFIED TIME (TIMER TRANSMISSION)
- TRANSMITTING TWO ORIGINAL PAGES AS A SINGLE PAGE (2IN1)
- TRANSMITTING THE FRONT AND BACK SIDES OF A CARD ON ONE SHEET OF PAPER (CARD SHOT)
- TRANSMITTING A LARGE NUMBER OF PAGES (JOB BUILD)
- CHANGING THE PRINT SETTINGS FOR THE TRANSACTION REPORT (TRANSACTION REPORT)
- PRIORITY TRANSMISSION OF A STORED JOB
- CANCELLING AN SCAN TRANSMISSION
- RECEIVING AN INTERNET FAX
- TRANSFERRING RECEIVED INTERNET-FAXES TO ANOTHER MACHINE WHEN PRINTING IS NOT POSSIBLE (FORWARDING FUNCTION)
- FORWARDING RECEIVED INTERNET FAXES TO AN E-MAIL ADDRESS (INBOUND ROUTING SETTINGS)
- METADATA DELIVERY (DATA ENTRY)
- PREPARATIONS FOR METADATA TRANSMISSION
- TRANSMITTING METADATA
- STORING FROM THE OPERATION PANEL
- STORING ONE-TOUCH KEYS (only addresses for Scan to E-mail and Internet-Fax)
- EDITING AND DELETING ONE-TOUCH KEYS
- PROGRAMMING A GROUP KEY
- EDITING AND DELETING GROUP KEYS
- STORING SENDER INFORMATION
- EDITING AND DELETING SENDER INFORMATION
- STORING A GROUP INDEX
- PRINTING PROGRAMMED INFORMATION
- STORING A PROGRAM
- EDITING AND DELETING PROGRAMS
- TROUBLESHOOTING
- ADMINISTRATOR SETTINGS
- NETWORK SCANNER / INTERNET FAX SPECIFICATIONS
- NUMBER OF ITEMS THAT CAN BE STORED WHEN A HARD DRIVE IS INSTALLED, AND WHEN NOT INSTALLED
SPECIAL MODES
3-4
ERASING EDGE SHADOWS (ERASE)
The erase function is used to erase the shadow lines on images produced when scanning thick originals or books.
The erase modes that can be selected are shown below. The erase width is approximately 10 mm (1/2") in its initial
setting.
■ USING ERASE
1
Switch to the desired mode and touch the
[SPECIAL MODES] key.
If the address book screen
appears, touch the
[CONDITION SETTINGS]
key to display the
condition settings screen
(page 1-13
).
2
Touch the [ERASE] key.
3
Select the desired erase mode.
Select one of the three
erase modes. The
selected key will be
highlighted.
4
If desired, set the width of the edge to be
erased (touch the key or the key to
set the width).
The erase width can be
set from 0 mm (0") to
20 mm (1") in 1 mm (1/8")
increments.
5
Touch the outer [OK] key.
You will return to the
screen of step 1 and an
erase icon will appear
next to the
[EXPOSURE] key.
To cancel erase, touch
the [CANCEL] key.
6
Perform the send procedure as explained
in "SENDING AN IMAGE".
●For scan mode, see page 2-2.
●For Internet fax mode, see page 2-6
.
EDGE ERASE
Erases shadows at edges
that appear when scanning
thick originals or books.
CENTRE ERASE
Eliminates shadow lines
produced by the bindings
of bound documents.
EDGE + CENTRE ERASE
Eliminates shadow lines around
the edges of images and
eliminates the shadow at the
centre of images.
Using edge erase
Your machine The other machine
Transmission to
other machine
Combining “edge erase”
with “dual page scan” on
the following page
SPECIAL MODES
ADDRESS REVIEW
FILE
ENTRY
QUICK FILE
TTINGS
ERASE
2in1
R CA
AM
EDGE
ERASE
ERASE
CENTRE
ERASE
EDGE+CENTRE
ERASE
NOTE
To cancel the erase function, touch the [CANCEL]
key on the erase setting screen. (step 4)
(0 20)
mm
CENTRE
10
OK
OK
CANCEL