MX-M350U/N/M450U/N Operation-Manual Scanner GB
Table Of Contents
- INTRODUCTION
- TABLE OF CONTENTS
- ABOUT THE NETWORK SCANNER FUNCTION
- SETTINGS AND PROGRAMMING REQUIRED FOR THE NETWORK SCANNER FEATURE
- ACCESSING WEB PAGES
- ABOUT THE WEB PAGES (FOR USERS)
- ABOUT THE WEB PAGES (FOR THE ADMINISTRATOR)
- BASIC SETTINGS FOR NETWORK SCANNING
- SETTING UP DESTINATION INFORMATION
- STORING SENDER INFORMATION (Scan to E-mail)
- SETTING UP INTERNET-FAX PARAMETERS
- SETTING UP SERVERS
- PROTECTING INFORMATION PROGRAMMED IN THE WEB PAGE ("Passwords")
- BASE SCREEN
- SENDING AN IMAGE
- DESTINATION INPUT METHODS
- SCANNING SETTINGS (ORIGINAL SIZE, EXPOSURE, RESOLUTION AND FILE FORMAT)
- SPECIAL MODES
- PROGRAMMING FREQUENTLY USED OPERATIONS (PROGRAM)
- ERASING EDGE SHADOWS (ERASE)
- TRANSMITTING A DIVIDED ORIGINAL (DUAL PAGE SCAN)
- AUTOMATIC TRANSMISSION AT A SPECIFIED TIME (TIMER TRANSMISSION)
- TRANSMITTING TWO ORIGINAL PAGES AS A SINGLE PAGE (2IN1)
- TRANSMITTING THE FRONT AND BACK SIDES OF A CARD ON ONE SHEET OF PAPER (CARD SHOT)
- TRANSMITTING A LARGE NUMBER OF PAGES (JOB BUILD)
- CHANGING THE PRINT SETTINGS FOR THE TRANSACTION REPORT (TRANSACTION REPORT)
- PRIORITY TRANSMISSION OF A STORED JOB
- CANCELLING AN SCAN TRANSMISSION
- RECEIVING AN INTERNET FAX
- TRANSFERRING RECEIVED INTERNET-FAXES TO ANOTHER MACHINE WHEN PRINTING IS NOT POSSIBLE (FORWARDING FUNCTION)
- FORWARDING RECEIVED INTERNET FAXES TO AN E-MAIL ADDRESS (INBOUND ROUTING SETTINGS)
- METADATA DELIVERY (DATA ENTRY)
- PREPARATIONS FOR METADATA TRANSMISSION
- TRANSMITTING METADATA
- STORING FROM THE OPERATION PANEL
- STORING ONE-TOUCH KEYS (only addresses for Scan to E-mail and Internet-Fax)
- EDITING AND DELETING ONE-TOUCH KEYS
- PROGRAMMING A GROUP KEY
- EDITING AND DELETING GROUP KEYS
- STORING SENDER INFORMATION
- EDITING AND DELETING SENDER INFORMATION
- STORING A GROUP INDEX
- PRINTING PROGRAMMED INFORMATION
- STORING A PROGRAM
- EDITING AND DELETING PROGRAMS
- TROUBLESHOOTING
- ADMINISTRATOR SETTINGS
- NETWORK SCANNER / INTERNET FAX SPECIFICATIONS
- NUMBER OF ITEMS THAT CAN BE STORED WHEN A HARD DRIVE IS INSTALLED, AND WHEN NOT INSTALLED
SENDING AN IMAGE
2-9
20
If you have another page to scan, change
pages and then press the [START] key.
Repeat this sequence until all pages have been
scanned. You can change the resolution and
exposure settings as needed for each page (refer
to page 2-18
).
If no action is taken for one minute, scanning
automatically ends and the transmission job is stored.
21
After the final page is scanned, touch the
[READ-END] key.
The machine makes a
beep sound to inform
you that the
transmission job is
stored and the [JOB
STORED] appears in the
message display. (The
destination is automatically called and the
document transmitted after previously stored jobs
are completed.) Open the document glass cover
and remove the document.
READ-END
GINAL. Pg.No.2
PRESS [READ-END].
NOTES
● Cancelling transmission
To cancel transmission while the [SCANNING ORIGINAL...] appears in the display or before the [READ-END] key is touched,
press the [C] key or the [CA] key. To cancel a transmission job that is already stored, press the [JOB STATUS] key and cancel
the job as explained on page 3-13
.
● Internet fax settings such as send confirmation, image rotation, and attachment size limit settings can be configured in "I-Fax
send settings" (page 8-7
) in the administrator settings.
● If the power is turned off or a power failure occurs while a document is being scanned in the automatic document feeder, the
machine will stop and a document misfeed will occur. After the power is restored, remove the document as explained on page
2-20 of the operation manual (for general information and copier operation).
● A job number appears in the display with "JOB STORED." when a transmission job is stored. If you make a note of this
number, you can use the number to easily locate the job when checking the results of the transmission in the job status screen
for a broadcast transmission (page 2-13
), or in the transaction report or activity report.