MX-M350U/N/M450U/N Operation-Manual Printer GB
Table Of Contents
- INTRODUCTION
- TABLE OF CONTENTS
- BASIC PRINTING PROCEDURE
- USING ACCOUNT NUMBERS WHEN PRINTING
- VIEWING PRINTER DRIVER HELP
- SAVING FREQUENTLY USED PRINT SETTINGS
- CHANGING THE PRINTER DRIVER DEFAULT SETTINGS
- BASIC PRINTING PROCEDURE
- USING ACCOUNT NUMBERS WHEN PRINTING
- FREQUENTLY USED FUNCTIONS
- CONVENIENT PRINTING FUNCTIONS
- CREATING A PAMPHLET (Pamphlet/Pamphlet Staple)
- INCREASING THE MARGIN (Margin Shift)
- ROTATING THE PRINT IMAGE 180 DEGREES (Rotate 180 degrees)
- ENLARGING/REDUCING THE PRINT IMAGE (Scale/XY-Zoom)
- REVERSING THE IMAGE (Mirror Image)
- ADJUSTING THE BRIGHTNESS AND CONTRAST OF THE IMAGE (Image Adjustment)
- PRINTING FAINT TEXT AND LINES IN BLACK (Text To Black/Vector To Black)
- ADDING A WATERMARK TO PRINTED PAGES (Watermark)
- CREATING OVERLAYS FOR PRINT DATA (Overlays)
- PRINTING SPECIFIED PAGES ON DIFFERENT PAPER (Different Paper)
- ADDING INSERTS WHEN PRINTING ON TRANSPARENCY FILM (Transparency Inserts)
- PRINTING A CARBON COPY (Carbon Copy)
- USING TWO MACHINES TO PRINT A LARGE PRINT JOB (Tandem Print)
- SAVING AND USING PRINT FILES (Retention/Document Filing)
- REMOTE OPERATION VIA A NETWORK
- ABOUT THE WEB PAGES (FOR USERS)
- ABOUT THE WEB PAGES (FOR THE ADMINISTRATOR)
- MAKING CONFIGURATION SETTING
- HOLD JOB LIST
- ADMINISTRATOR SETTINGS
- DESCRIPTION OF SETTINGS
- TROUBLESHOOTING
- PRINTER DRIVER SPECIFICATIONS
- PRINTER SPECIFICATIONS
- NOTICE PAGE PRINTING
- PRINT AREA
DESCRIPTION OF SETTINGS
8-6
■ Interface settings
These settings are used to control data transmitted to
the USB port or network port of this printer.
The following items can be configured in the "Interface
settings"
● Hexadecimal dump mode
● I/O timeout
● Enable USB port
● USB port emulation switching
● Enable network port
● Network port emulation switching
● Port switching method
Hexadecimal dump mode
This setting is used to output the print data from a
computer in the hexadecimal dump format with
corresponding characters (ASCII). This setting is used
to check proper transmission of print data from the
computer to the printer.
Output example of hexadecimal dump mode
I/O timeout
This setting is used to set the length of time to wait for
an I/O to complete a job on the USB port or the network
port. If the data stream to the port does not transmit
data for a length of time exceeding the timeout, the job
will cancel and the next job will start processing.
The I/O timeout setting is used to set the amount of time
after which an I/O timeout will occur when waiting for
print data.
Default setting: 20 seconds
Enable USB port
This setting is used to enable or disable printing from
the USB port.
Default setting: Enable
USB port emulation switching
If the machine is connected using the USB port, select
the emulated printer language.
Enable network port
This setting is used to enable or disable printing from
the network port.
Default setting: Enable
Network port emulation switching
This setting is used to specify a printer language to
emulate when the printer is connected to a computer
through the network port.
The setting items are the same as those of "USB port
emulation switching".
Port switching method
The machine can use the two ports shown below for
printing. This setting is used to select when switching
between ports will take place. "SWITCH AT END OF
JOB" or "SWITCH AFTER I/O TIMEOUT" can be
selected. When "SWITCH AT END OF JOB" is
selected, the port will be automatically selected after
each print job is completed. When "SWITCH AFTER I/
O TIMEOUT" is selected, the port will be automatically
selected if the time set in the I/O Timeout setting
elapses.
● USB port
● Network port
NOTE
The allowable range of the time is 1 to 999 seconds.
Setting items Description
Auto The printer language will switch
automatically in accordance with the
data from the computer.
PostScript PostScript emulation is used to print
the data from the computer. (An
optional PS3 expansion kit is
needed.)
PCL PCL emulation is used to print the
data from the computer.
NOTE
It is recommended to set "AUTO" (default setting)
unless an error due to this setting occurs frequently.
NOTE
It is recommended to set "AUTO" (default setting)
unless an error due to this setting occurs frequently.