MX-M350U/N/M450U/N Operation-Manual Copier GB
Table Of Contents
- Part 1: General Information
- PRODUCT CONFIGURATIONS
- OPERATION MANUALS
- INSTALLATION REQUIREMENTS
- CAUTIONS
- CONTENTS
- CHAPTER 1
- CHAPTER 2
- LOADING PAPER
- Loading paper in paper tray 1
- Changing the paper size in paper tray 1
- Specifications of paper trays
- Setting the paper type and paper size
- Setting the paper size when a special size is loaded
- Programming and editing paper types
- Loading paper in the multi purpose drawer
- Specifications (multi purpose drawer)
- Loading paper in the stand/3 x 500 sheet paper drawer
- Specifications (stand/3 x 500 sheet paper drawer)
- Loading paper in the stand/MPD & 2000 sheet paper drawer
- Specifications (stand/MPD & 2000 sheet paper drawer)
- SYSTEM SETTINGS
- REPLACING THE TONER CARTRIDGE
- STORAGE OF SUPPLIES
- MISFEED REMOVAL
- REMOVING AN ORIGINAL MISFEED
- TROUBLESHOOTING
- LOADING PAPER
- CHAPTER 3
- DUPLEX MODULE
- MAIL-BIN STACKER
- FINISHER
- SADDLE STITCH FINISHER
- SHARP OSA
- APPLICATION COMMUNICATION MODULE (MX-AMX2)
- EXTERNAL ACCOUNT MODULE (MX-AMX3)
- Part 2: Copier Operation
- CHAPTER 4
- AUTOMATIC DOCUMENT FEEDER
- PLACING ORIGINALS
- CHECKING THE SIZE OF A PLACED ORIGINAL
- STORING, DELETING, AND USING ORIGINAL SIZES
- NORMAL COPYING
- ADJUSTING THE EXPOSURE
- REDUCTION/ENLARGEMENT/ZOOM
- SPECIAL PAPERS
- CHAPTER 5
- SPECIAL MODES
- General procedure for using special functions
- Margin shift
- Erase
- Dual page copy
- Pamphlet copy
- Job build
- Tandem copy
- Covers/inserts
- About the explanations of covers and inserts
- Preparations for using covers and inserts
- Procedure for inserting front and back cover paper
- Procedure for adding inserts
- Checking, editing, and deleting cover/insert pages
- Examples of covers and inserts
- Symbols used for covers and inserts
- Covers (One-sided copying of one-sided originals)
- Covers (Two-sided copying of one-sided originals)
- Covers (One-sided copying of Two-sided originals)
- Covers (Two-sided copying of two-sided originals)
- Inserts (One-sided copying of one-sided originals)
- Inserts (One-sided copying of two-sided originals)
- Transparency film with insert sheets
- Multi shot
- Book copy
- Card shot
- Mirror image
- B/W reverse
- Print menu
- Common operation procedure for using the print menu
- Printing in combination with other special functions
- Printing the date on copies
- Printing a stamp (reverse text) on copies
- Printing the page number on copies
- Examples of page number printing
- Printing entered text on copies
- Storing text sequences
- Editing and deleting stored text
- Checking and changing the print layout
- STORING, USING AND DELETING JOB PROGRAMS
- INTERRUPTING A COPY RUN
- SPECIAL MODES
- CHAPTER 6
- CHAPTER 7
- CHAPTER 8
0-3
INSTALLATION REQUIREMENTS
Improper installation may damage this product. Please note the following during initial installation and whenever the
machine is moved.
1.The machine should be installed near an
accessible power outlet for easy connection.
2.Be sure to connect the power cord only to a
power outlet that meets the specified voltage and
current requirements. Also make certain the
outlet is properly grounded.
●For the power supply requirements, see the
name plate on the back of the main unit.
3.Do not install your machine in areas that are:
●damp, humid, or very dusty
●exposed to direct sunlight
●poorly ventilated
●subject to extreme temperature or humidity
changes, e.g., near an air conditioner or heater.
4.Be sure to allow the required space around the
machine for servicing and proper ventilation.
A small amount of ozone is produced within the machine during operation. The emission level is insufficient to
cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m
3
) calculated as an 8 hr. time-
weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier
in a ventilated area.
60cm
80cm
30cm
60cm