MX-M350U/N/M450U/N Operation-Manual Copier GB
Table Of Contents
- Part 1: General Information
- PRODUCT CONFIGURATIONS
- OPERATION MANUALS
- INSTALLATION REQUIREMENTS
- CAUTIONS
- CONTENTS
- CHAPTER 1
- CHAPTER 2
- LOADING PAPER
- Loading paper in paper tray 1
- Changing the paper size in paper tray 1
- Specifications of paper trays
- Setting the paper type and paper size
- Setting the paper size when a special size is loaded
- Programming and editing paper types
- Loading paper in the multi purpose drawer
- Specifications (multi purpose drawer)
- Loading paper in the stand/3 x 500 sheet paper drawer
- Specifications (stand/3 x 500 sheet paper drawer)
- Loading paper in the stand/MPD & 2000 sheet paper drawer
- Specifications (stand/MPD & 2000 sheet paper drawer)
- SYSTEM SETTINGS
- REPLACING THE TONER CARTRIDGE
- STORAGE OF SUPPLIES
- MISFEED REMOVAL
- REMOVING AN ORIGINAL MISFEED
- TROUBLESHOOTING
- LOADING PAPER
- CHAPTER 3
- DUPLEX MODULE
- MAIL-BIN STACKER
- FINISHER
- SADDLE STITCH FINISHER
- SHARP OSA
- APPLICATION COMMUNICATION MODULE (MX-AMX2)
- EXTERNAL ACCOUNT MODULE (MX-AMX3)
- Part 2: Copier Operation
- CHAPTER 4
- AUTOMATIC DOCUMENT FEEDER
- PLACING ORIGINALS
- CHECKING THE SIZE OF A PLACED ORIGINAL
- STORING, DELETING, AND USING ORIGINAL SIZES
- NORMAL COPYING
- ADJUSTING THE EXPOSURE
- REDUCTION/ENLARGEMENT/ZOOM
- SPECIAL PAPERS
- CHAPTER 5
- SPECIAL MODES
- General procedure for using special functions
- Margin shift
- Erase
- Dual page copy
- Pamphlet copy
- Job build
- Tandem copy
- Covers/inserts
- About the explanations of covers and inserts
- Preparations for using covers and inserts
- Procedure for inserting front and back cover paper
- Procedure for adding inserts
- Checking, editing, and deleting cover/insert pages
- Examples of covers and inserts
- Symbols used for covers and inserts
- Covers (One-sided copying of one-sided originals)
- Covers (Two-sided copying of one-sided originals)
- Covers (One-sided copying of Two-sided originals)
- Covers (Two-sided copying of two-sided originals)
- Inserts (One-sided copying of one-sided originals)
- Inserts (One-sided copying of two-sided originals)
- Transparency film with insert sheets
- Multi shot
- Book copy
- Card shot
- Mirror image
- B/W reverse
- Print menu
- Common operation procedure for using the print menu
- Printing in combination with other special functions
- Printing the date on copies
- Printing a stamp (reverse text) on copies
- Printing the page number on copies
- Examples of page number printing
- Printing entered text on copies
- Storing text sequences
- Editing and deleting stored text
- Checking and changing the print layout
- STORING, USING AND DELETING JOB PROGRAMS
- INTERRUPTING A COPY RUN
- SPECIAL MODES
- CHAPTER 6
- CHAPTER 7
- CHAPTER 8
FINISHER
3-13
3
Troubleshooting finisher problems
Check the list below before calling for service.
Problem Check Solution or cause
The finisher does
not operate.
Are any finisher covers open? Close all covers.
Message indicating need to remove
paper from the stapler compiler
displayed?
Open the finisher
as described in
step 4 on page
3-12 and remove
all paper from the
stapler compiler.
Stapling cannot be
performed.
Is a "CHECK THE STAPLER UNIT" or
"CHECK STAPLER POSITION OR
STAPLER JAM" message displayed?
Check the staple unit. (See page 3-11.)
Is a message "ADD STAPLES"
displayed?
Replace the staple cartridge. (See page 3-10.)
Different size paper included?
Stapling cannot be performed onto different size
paper.
Stapled sets are not
stacked correctly or
some sheets in a set
are not stapled.
Paper heavily curled?
Paper may be curled heavily depending on the
paper type and quality. Remove paper from the
paper tray or the bypass tray, turn it upside down,
and load it again.