MX-M350U/N/M450U/N Operation-Manual Copier GB
Table Of Contents
- Part 1: General Information
- PRODUCT CONFIGURATIONS
- OPERATION MANUALS
- INSTALLATION REQUIREMENTS
- CAUTIONS
- CONTENTS
- CHAPTER 1
- CHAPTER 2
- LOADING PAPER
- Loading paper in paper tray 1
- Changing the paper size in paper tray 1
- Specifications of paper trays
- Setting the paper type and paper size
- Setting the paper size when a special size is loaded
- Programming and editing paper types
- Loading paper in the multi purpose drawer
- Specifications (multi purpose drawer)
- Loading paper in the stand/3 x 500 sheet paper drawer
- Specifications (stand/3 x 500 sheet paper drawer)
- Loading paper in the stand/MPD & 2000 sheet paper drawer
- Specifications (stand/MPD & 2000 sheet paper drawer)
- SYSTEM SETTINGS
- REPLACING THE TONER CARTRIDGE
- STORAGE OF SUPPLIES
- MISFEED REMOVAL
- REMOVING AN ORIGINAL MISFEED
- TROUBLESHOOTING
- LOADING PAPER
- CHAPTER 3
- DUPLEX MODULE
- MAIL-BIN STACKER
- FINISHER
- SADDLE STITCH FINISHER
- SHARP OSA
- APPLICATION COMMUNICATION MODULE (MX-AMX2)
- EXTERNAL ACCOUNT MODULE (MX-AMX3)
- Part 2: Copier Operation
- CHAPTER 4
- AUTOMATIC DOCUMENT FEEDER
- PLACING ORIGINALS
- CHECKING THE SIZE OF A PLACED ORIGINAL
- STORING, DELETING, AND USING ORIGINAL SIZES
- NORMAL COPYING
- ADJUSTING THE EXPOSURE
- REDUCTION/ENLARGEMENT/ZOOM
- SPECIAL PAPERS
- CHAPTER 5
- SPECIAL MODES
- General procedure for using special functions
- Margin shift
- Erase
- Dual page copy
- Pamphlet copy
- Job build
- Tandem copy
- Covers/inserts
- About the explanations of covers and inserts
- Preparations for using covers and inserts
- Procedure for inserting front and back cover paper
- Procedure for adding inserts
- Checking, editing, and deleting cover/insert pages
- Examples of covers and inserts
- Symbols used for covers and inserts
- Covers (One-sided copying of one-sided originals)
- Covers (Two-sided copying of one-sided originals)
- Covers (One-sided copying of Two-sided originals)
- Covers (Two-sided copying of two-sided originals)
- Inserts (One-sided copying of one-sided originals)
- Inserts (One-sided copying of two-sided originals)
- Transparency film with insert sheets
- Multi shot
- Book copy
- Card shot
- Mirror image
- B/W reverse
- Print menu
- Common operation procedure for using the print menu
- Printing in combination with other special functions
- Printing the date on copies
- Printing a stamp (reverse text) on copies
- Printing the page number on copies
- Examples of page number printing
- Printing entered text on copies
- Storing text sequences
- Editing and deleting stored text
- Checking and changing the print layout
- STORING, USING AND DELETING JOB PROGRAMS
- INTERRUPTING A COPY RUN
- SPECIAL MODES
- CHAPTER 6
- CHAPTER 7
- CHAPTER 8
2-22
REMOVING AN ORIGINAL MISFEED
Removing a misfed original from the automatic document feeder
If an original misfeed occurs in the automatic document feeder, follow the steps below to remove the misfed original.
Check locations A and B in the diagram at left to
remove the original.
1
Removing misfeeds from each location.
● Check location A
Open the document
feeding area cover and
gently remove the
misfed original without
tearing it.
Close the cover securely
so that cover clicks into
place.
● Check location B
● Misfeed in the transfer unit
Open the document
feeder and turn the
green rotating knob in
the direction of the arrow
to remove any misfed
originals.
2
Open and close the document feeder.
Opening and closing the
cover clears the misfeed
display. Copying cannot
be resumed until this
step is performed.
However, this step is not
necessary after a
misfeed is removed from location B.
A message may appear indicating the number of
originals which must be returned to the document
feeder tray. Return the originals to the document
feeder tray and press the [START] key.
NOTES
● For misfeed removal in the main unit and other peripheral devices, see page 2-17
● When a misfeed occurs, touch the [INFORMATION] key to display detailed information for misfeed removal.
Document feeding area
cover