MX-M350U/N/M450U/N Operation-Manual Copier GB
Table Of Contents
- Part 1: General Information
- PRODUCT CONFIGURATIONS
- OPERATION MANUALS
- INSTALLATION REQUIREMENTS
- CAUTIONS
- CONTENTS
- CHAPTER 1
- CHAPTER 2
- LOADING PAPER
- Loading paper in paper tray 1
- Changing the paper size in paper tray 1
- Specifications of paper trays
- Setting the paper type and paper size
- Setting the paper size when a special size is loaded
- Programming and editing paper types
- Loading paper in the multi purpose drawer
- Specifications (multi purpose drawer)
- Loading paper in the stand/3 x 500 sheet paper drawer
- Specifications (stand/3 x 500 sheet paper drawer)
- Loading paper in the stand/MPD & 2000 sheet paper drawer
- Specifications (stand/MPD & 2000 sheet paper drawer)
- SYSTEM SETTINGS
- REPLACING THE TONER CARTRIDGE
- STORAGE OF SUPPLIES
- MISFEED REMOVAL
- REMOVING AN ORIGINAL MISFEED
- TROUBLESHOOTING
- LOADING PAPER
- CHAPTER 3
- DUPLEX MODULE
- MAIL-BIN STACKER
- FINISHER
- SADDLE STITCH FINISHER
- SHARP OSA
- APPLICATION COMMUNICATION MODULE (MX-AMX2)
- EXTERNAL ACCOUNT MODULE (MX-AMX3)
- Part 2: Copier Operation
- CHAPTER 4
- AUTOMATIC DOCUMENT FEEDER
- PLACING ORIGINALS
- CHECKING THE SIZE OF A PLACED ORIGINAL
- STORING, DELETING, AND USING ORIGINAL SIZES
- NORMAL COPYING
- ADJUSTING THE EXPOSURE
- REDUCTION/ENLARGEMENT/ZOOM
- SPECIAL PAPERS
- CHAPTER 5
- SPECIAL MODES
- General procedure for using special functions
- Margin shift
- Erase
- Dual page copy
- Pamphlet copy
- Job build
- Tandem copy
- Covers/inserts
- About the explanations of covers and inserts
- Preparations for using covers and inserts
- Procedure for inserting front and back cover paper
- Procedure for adding inserts
- Checking, editing, and deleting cover/insert pages
- Examples of covers and inserts
- Symbols used for covers and inserts
- Covers (One-sided copying of one-sided originals)
- Covers (Two-sided copying of one-sided originals)
- Covers (One-sided copying of Two-sided originals)
- Covers (Two-sided copying of two-sided originals)
- Inserts (One-sided copying of one-sided originals)
- Inserts (One-sided copying of two-sided originals)
- Transparency film with insert sheets
- Multi shot
- Book copy
- Card shot
- Mirror image
- B/W reverse
- Print menu
- Common operation procedure for using the print menu
- Printing in combination with other special functions
- Printing the date on copies
- Printing a stamp (reverse text) on copies
- Printing the page number on copies
- Examples of page number printing
- Printing entered text on copies
- Storing text sequences
- Editing and deleting stored text
- Checking and changing the print layout
- STORING, USING AND DELETING JOB PROGRAMS
- INTERRUPTING A COPY RUN
- SPECIAL MODES
- CHAPTER 6
- CHAPTER 7
- CHAPTER 8
2-2
LOADING PAPER
If the paper runs out during printing, a message will appear in the display.
Follow the procedure below to load paper.
Loading paper in paper tray 1
1
Pull out paper tray 1.
Gently pull the tray out
until it stops.
2
Load paper into the tray.
Do not load paper above
the maximum height line
(approximately 500
sheets of 80 g/m
2
(20
lbs.) paper).
3
Gently push tray 1 into the machine.
Push the tray firmly all the way into the machine.
4
Set the paper type.
If you change the paper type setting if the paper
type is changed in either paper tray, refer to
"Setting the paper type and paper size" (page
2-5).
5
Loading paper in paper tray 1 is now
complete.
Changing the paper size in paper tray 1
For paper tray 1, A4, B5 or 8-1/2" x 11" size paper can be set. Use the following procedure to change the size as
needed.
1
Pull out paper tray 1.
If paper remains in the tray, remove it.
2
Adjust the guide plates A and B in the tray
to the length and width of the paper.
The guide plates A and
B are slidable. Adjust
them to the paper size to
be loaded while
squeezing their lock
levers.
3
Load paper into the tray.
4
Gently push tray 1 into the machine.
Push the tray firmly all the way into the machine.
5
Set the paper size.
Be sure to set the paper size and paper type
referring to "Setting the paper type and paper size"
(page
2-5).
If this is not done, paper misfeeds will occur.
6
Changing paper size in paper tray 1 is now
complete.
NOTES
● Do not use curled or folded paper. Doing so may cause a misfeed.
● For best results use paper supplied by SHARP. (See page 2-4.)
● When you change the paper type and size in paper tray 1, set the paper type and size referring to "Setting the
paper type and paper size" (page
2-5).
● Do not place heavy objects or press hard on any tray which is pulled out.
● Load paper with the print side face up. However, when the paper type is set to "PRE-PRINTED",
"PRE-PUNCHED" or "LETTER HEAD", load the paper face down*.
* If the two-sided function is disabled using "DISABLING OF DUPLEX" in the administrator settings (page 11
of the administrator settings guide), load the paper face up.