MX-FX13 Operation-Manual GB
Table Of Contents
- INTRODUCTION
- CONNECTING AN EXTENSION PHONE
- CONTENTS
- TO USE THIS PRODUCT CORRECTLY ASA FACSIMILE
- 1. BEFORE USING THE FAXFUNCTION
- 2. BASIC OPERATIONS
- 3. ADVANCED TRANSMISSIONMETHODS
- SENDING THE SAME DOCUMENT TO MULTIPLE DESTINATIONS IN A SINGLE OPERATION (BROADCAST TRANSMISSION)
- AUTOMATIC TRANSMISSION AT A SPECIFIED TIME (TIMER TRANSMISSION)
- TRANSMISSION AND RECEPTION USING THE POLLING FUNCTION
- INCLUDING SENDER INFORMATION ON FAXES
- FAXING A DIVIDED ORIGINAL (DUAL PAGE SCAN)
- ADDING A COVER SHEET/MESSAGE TO A FAX TRANSMISSION
- USING SETTINGS STORED AS A PROGRAM
- FORWARDING RECEIVED DATA TO A NETWORK ADDRESS (INBOUND ROUTING SETTINGS)
- FORWARDING RECEIVED FAXES TO ANOTHER MACHINE WHEN PRINTING IS NOT POSSIBLE (FORWARDING FUNCTION)
- SENDING A FAX DIRECTLY FROM A COMPUTER (PC-Fax)
- 4. TRANSMISSION USINGF-CODES
- 5. CONVENIENT METHODS OFUSE
- 6. PROGRAMMING
- 7. TROUBLESHOOTING
- 8. SYSTEM SETTINGS
- 9. APPENDIX
91
TROUBLESHOOTING
7
XX-XX OK When group dialling, broadcast transmission, or F-code relay request transmission
was performed,
xxx- : Indicates total number of transmissions.
xxx OK : Indicates completed transmissions.
NO S ADD FUNC When an F-code transmission was attempted,
(1) The other machine did not have the F-code function.
(2) An F-code was not programmed in the other machine.
S ADD TX FAIL When an F-code transmission was attempted,
(1) The sub-addresses did not match.
(2) The passcodes did not match.
(3) An F-code public box was set.
SA POLL ERR When F-code public box transmission was attempted,
(1) The F-code public box specified by the sub-address did not exist.
(2) The sub-address specified a box other than an F-code public box.
PASSCODE# ERR When F-code public box transmission was attempted,
(1) The passcodes did not match.
Reception result Explanation
OK Reception was completed successfully.
P. FAIL The power was turned off or a power failure occurred.
MEMORY FULL The image memory became full during substitute reception to memory.
LENGTH OVER
The transmitted document was over 1500 mm long and therefore could not be received.
NO RX ROLL When polling was attempted,
(1) Your fax number (sender's number) was not programmed in your machine.
(2) Your fax number was not programmed as a polling passcode number in the other
machine.
RX NO POLL When polling was attempted,
(1) The other machine did not have a polling function.
(2) The other machine did not have a document stored in polling memory.
ERRORxx xxxx Line conditions prevented the reception from taking place normally.
First 2 digits of line error code: Error code from 00 to 31.
Last 4 digits of line error code: Code for use by service technicians.
XX-XX OK When serial polling ended normally,
xxx- : Indicates total number of transmissions.
xxx OK : Indicates completed transmissions.
NO SA POLLING When F-code polling was attempted,
(1) The other machine did not have an F-code polling memory function.
(2) An F-code was not programmed in the other machine.
(3) The other machine did not have a document stored in polling memory.
SA POL TX ERR When F-code polling was attempted,
(1) The sub-addresses did not match.
(2) The passcodes did not match.
(3) The other machine's F-code memory boxes were for F-code relay request
transmission or for F-code confidential transmission.
S ADD RX FAIL When F-code reception was attempted,
(1) The sub-addresses did not match or were not programmed.
(2) The passcodes did not match or were not programmed.
(3) An F-code polling memory box was programmed.
JUNK FAX ERR Fax reception was denied by the reception denial function.
Sending result Explanation