CODE : 00ZMXM182/S1E (With optional SPF/RSPF installed) DIGITAL MULTIFUNCTIONAL SYSTEM (With optional SPF/RSPF installed) MX-M182/M182D MODEL MX-M202D/M232D MX-M182 MX-M182D MX-M202D MX-M232D CONTENTS [ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 [ 2 ] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 [ 3 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disconnect the AC cord before servicing the unit. LASER WAVE - LENGTH : 785 15mm Pulse times : 10.34 s 0.1 s/7mm ; MX-M182, MX-M182D, MX-M202D 8.665 s 0.1 s/7mm ; MX-M232D Out put power : Max. 0.
CONTENTS [1] GENERAL 1. Note for servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 [2] CONFIGURATION 1. System Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1 [3] SPECIFICATIONS 1. Copy mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1 2. Print mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 4 3. Scanner mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
[1] GENERAL •poorly ventilated 1. Note for servicing Pictogram The label ( ) in the fusing area of the machine indicates the following: : Caution, risk of danger : Caution, hot surface A. Warning for servicing •exposed to direct sunlight •The fusing area is hot. Exercise care in this area when removing misfeed paper. •Do not disassemble the laser unit. Do not insert a reflective material such as a screwdriver in the laser beam path. It may damage eyes by reflection of laser beams. B.
D. Note for handling PWB and electronic parts When handling the PWB and the electronic parts, be sure to observe the following precautions in order to prevent against damage by static electricity. 1) When in transit or storing, put the parts in an anti-static bag or an anti-static case and do not touch them with bare hands. 2) When and after removing the parts from an anti-static bag (case), use an earth band as shown below: •Put an earth band to your arm, and connect it to the machine.
[2] CONFIGURATION 1. System Configurations AR-VR7 (MX-M182 is standard.
Model Option MX-M182 MX-M182D/M202D/M232D AR-RP10 Reversing single pass feeder (RSPF) X O*1 AR-SP10 Single pass feeder (SPF) O O*2 AR-D36 250-sheet paper feed unit O O AR-D37 2x250-sheet paper feed unit O O AR-VR7 DOCUMENT COVER STD O*2 MX-NB12 NETWORK EXPANSION KIT O O MX-FX13 FACSIMILE EXPANSION KIT O*3 O*3 MX-XB17 FACSIMILE MOUNTING KIT O O MX-TR10 JOB SEPARATOR O O MX-EB14 EXPANSION MEMORY BOARD O O MX-PK10 PS3 EXPANSION KIT O*4 O*4 MX-USX1 SHARPDESK 1 LIC
[3] SPECIFICATIONS 1. Copy mode (4) Job efficiency A. Type Copy mode Type Paper exit Desk-top center tray / internal S to S S to D D to D B.
(2) Feedable paper H. Copy magnification ratio Paper size A3 B4 A4 A4-R B5 B5R A5 A5R A6R B6R Ledger 11x17 in Legal 8.5x14in. 8.5x13.4 *1 Foolscap 8.5x13 in Letter 11x8.5in Letter-R 8.5x11in Executive-R 7.25x10.5in. Invoice 8.5x5.5 in. Invoice-R 5.5x8.5 in 8K 16K 16KR COM10 1st tray 2nd tray 297x420 257x364 297x210 210x297 257x182 182x257 210x148.5 148.5x210 105x148.5 128.5x182 279.4x431.8 215.9x355.6 216x340 *1 215.9x330.2 279.4x215.9 215.9x279.4 184.2x266.7 215.9x139.7 139.7x215.
M. Additional functions N.
2. Print mode A. Printing function (1) Platform Item Support platform Content IBM PC/AT compatible machine (2) Support OS Main unit OS Windows Mac 98/Me NT 4.0 SP5 or later 2000 XP XPx64 Server 2003 Server 2003x64 Vista Vistax64 Server 2008 Server 2008x64 Windows 7 Windows 7x64 9.0-9.2.2 X 10.2.8 X 10.3.9 X 10.4.11 X 10.5- 10.5.8 X 10.6-10.6.
Function Advanced Brightness (Image adjustment) Overseas 0 - 100% Contrast (Image adjustment) 0 - 100%.
b.
Advanced Water marks Special Mode Option PCL6 PS 0 - 100% 0 - 100% 0 - 100% 0 - 100% Text To Black Yes / No Yes / No Vector To Black Yes / No Yes / No Right binding Yes/No Yes / No Watermark None / TOP SECRET / CONFIDENTIAL / None / TOP SECRET / CONFIDENTIAL / DRAFT / ORIGINAL / COPY DRAFT / ORIGINAL / COPY User Setting Add / Update / Delete Add / Update / Delete Position Center Center X: ±50 X: ±50 Y : ±50 Y : ±50 Size 6 - 300 6 - 300 Angle ±90 ±90 Grayscale 0 - 255 0 - 255 Edit Font Yes Yes Thick Lett
C.
(5) Pull Scan (TWAIN) USB TWAIN (Does not function in Network system) Windows 2000 Professional/Windows XP Home Edition/ Windows XP Professional/ Windows Vista/Windows 7 USB (System) Shall meet the operating conditions of each OS basically. (HDD) 8MB or more: 100MB or more is recommended (Monitor) 800x600dots or more Shall be able to display 256 colors or more.
b.
[4] CONSUMABLE PARTS 1.Supply system table A. North America, Middle America, South America No. Name Product name Content Life 1 Toner cartridge(Black) MX-235NT Toner cartridge Vinyl bag x1 x1 16K Default is Toner save mode. Life is 19K. (200V series) 2 Developer MX-235NV Developer x1 50K 3 Drum KIT AR-205DR Drum Drum fixing plate x1 x1 50K Remark Life setting by A4 6% document B. Brazil No.
G. Asia(Except the above)/Thailand/Hong Kong No. Name Product name Content Life Remark 1 Toner cartridge(Black) MX-235AT Toner cartridge Vinyl bag x1 x1 16K Life setting by A4 6% document 2 Toner cartridge(Black) MX-236AT Toner cartridge Vinyl bag x1 x1 8.4K Life setting by A4 6% document 3 Developer MX-235AV Developer x1 50K 4 Drum KIT AR-205DR Drum Drum fixing plate x1 x1 50K 2. Environmental conditions A. Transport conditions B.
3. Production number identification The label on the toner cartridge shows the date of production. The lot number, printed on the front side flange, is composed of 10 digits, each digit showing the following content: 1 2 3 4 5 6 7 8 9 10 The lot number is of 10 digits. Each digit indicates the content as follows. The number is printed on the flange on the front side. Production place Serial number Year/ Month/ Day Ver.No.
[5] EXTERNAL VIEWS AND INTERNAL STRUCTURES 1. Appearance 3 13 8 9 7 4 5 5 14 1 6 10 15 2 12 11 16 17 18 1 USB 2.0 port Connect to your computer to this port to use the printer and scanner functions. 2 Charger cleaner Use to clean the transfer charger. 3 Glass cleaner Use to clean the original scanning glass. 4 Document glass Place an original that you wish to scan face down here. 5 Handles Use to move the machine. 6 Power switch Press to turn the machine power on and off.
2. Internal 23 21 22 27 24 19 26 20 25 28 29 19 Toner cartridge lock release lever To replace the toner cartridge, pull out the toner cartridge while pushing on this lever. 20 Toner cartridge Contains toner. 21 Document feeder tray (when the SPF/ RSPF is installed) Place the original(s) that you wish to scan face up here. Up to 40 sheets can be placed. 22 Original guides (when the SPF/RSPF is Adjust to the size of the originals.
3. Operation Section 1 2 3 01 02 03 04 05 4 5 6 7 8 9 10 11 DEF JKL MNO PQRS TUV WXYZ FAX STATUS COPY SHIFT 06 07 08 09 10 11 12 13 14 15 REDIAL/PAUSE PRINT INTERRUPT ABC GHI SPEAKER 12 ON LINE DATA BACK OK SPECIAL FUNCTION SCAN SPEED 16 17 18 19 20 21 22 23 24 25 SYMBOL FAX COMM. SETTING LINE DATA COPY EXPOSURE SCAN COLOUR MODE FAX PROGRAM @.
4. Motor, solenoid, clutch 13 1 12 2 3 11 4 6 5 7 8 10 No. Name Code Function operation 1 Mirror motor 2 Toner motor 3 Duplex motor DPX Switchback operation and paper exit motor in duplex. (MX-M182D/M202D/M232D) 4 Main motor MM Drives the machine. 5 1st tray paper feed clutch 6 PS clutch 7 Bypass tray paper transport clutch MPTC Drives the bypass tray paper transport roller.
5. Sensor, switch 1 17 20 3 (AB) (AB) (INCH) 19 18 4 (INCH) 16 15 5 6 2 7 14 13 8 9 12 No. Name Code 11 10 Function operation 1 Mirror home position sensor MHPS Detects the mirror (scanner unit) home position. 2 Side door switch DSWR Side door open detection 3 Paper exit sensor (paper exit side) POD1 Detects paper exit.
6. PWB unit 2 1 8 3 7 9 4 6 5 No.
7. Cross sectional view 1 2 3 4 56 7 18 8 9 10 11 12 13 14 15 23 22 21 20 19 17 16 No. Name Function/Operation 1 Copy lamp Image radiation lamp 2 Copy lamp unit Operates in synchronization with No. 2/3 mirror unit to radiate documents sequentially. 3 LSU unit Converts image signals into laser beams to write on the drum. 4 Lens unit Reads images with the lens and the CCD. 5 MC holder unit Supplies negative charges evenly on the drum. 6 Paper exit roller Used to discharge paper.
[6] ADJUSTMENTS 1. Adjustment item list Section A B Adjustment item Process section Mechanism section Adjustment procedure/SIM No. (1) Developing doctor gap adjustment Developing doctor gap adjustment (2) MG roller main pole position adjustment MG roller main pole position adjustment (3) Developing bias voltage check (4) Main charger voltage check (1) Image position adjustment SIM-50 (2) Main scanning direction (FR direction) distortion balance adjustment No.
(3) Developing bias voltage check B. Mechanism section Note: Use a digital multi-meter with an internal resistance of 10M or more. (1) Image position adjustment 1) Set the digital multi-meter range above 500 Vdc. 2) Put the test rod of the digital multi-meter on the developing bias voltage output check pin. 3) Turn on the power, execute SIM25-1. Note:In advance to this adjustment, the sub scanning magnification ratio adjustment must be performed. a.
7) Set the main cassette print start position value (TRAY1) to [1] and make a copy. The print start position is shifted inside the document edge. 10) Set the lead edge void adjustment value (DEN-A)* again. • 1 step of the set value corresponds to about 0.1mm shift. • Calculate the set value from the formula below. B/0.05 (mm) = Lead edge void adjustment value 5mm 5 4mm 10 2.5mm 5 *The dimension varies depending on the model. 2.
Adjustment mode SPF image lead edge position (1st print surface) SIM d. Paper off center adjustment (SIM50-10) Display text array SIM 50-6 Set value Spec value SIDE1 1 step: 0.1mm shift Lead edge void: 1 - 4mm Set range 1 - 99 Image loss: 3mm or less 1) Set a test chart (UKOG-0089CSZZ) on the document table. 2) Select a paper feed port and make a copy. Compare the copy and the test chart. If necessary, perform the following adjustment procedure. 3) Execute SIM 50-10.
(2) Main scanning direction (FR direction) distortion balance adjustment 1) Remove the OC glass and the right cabinet. (1) (1) (2) 4) Loosen the set screw of the scanner drive pulley which is not in contact with No. 2/3 mirror base unit positioning plate. 5) Without moving the scanner drive pulley shaft, manually turn the scanner drive pulley until the positioning plate is brought into contact with No. 2/3 mirror base unit, then fix the scanner drive pulley.
(3) Main scanning direction (FR direction) distortion adjustment 4) Loosen the mirror base drive pulley fixing screw on the front frame side or on the rear frame side. This adjustment must be performed in the following cases: • When the mirror base drive wire is replaced. • When the lamp unit, or No. 2/3 mirror holder is replaced. • When a copy as shown is made. When La < Lb Turn the mirror base drive pulley on the front frame side in the arrow direction A.
1) Making of a test sheet Make test sheet by drawing parallel lines at 10mm from the both ends of A3 (11" x 17") white paper as shown below. (These lines must be correctly parallel to each other.) When La > Lb Shift the mirror base B rail upward by the half of the difference of La - Lb. Parallel line Parallel line 10mm When La < Lb Shift the mirror base B rail downward by the half of the difference of Lb - La. Example: When La = 12mm and Lb = 9mm, shift the mirror base B rail upward by 1.5mm.
Note: A judgment must be made with 200mm width, and must not be made with 100mm width. Adjustment mode Main scanning direction magnification ratio SIM Display text array 48-1 F-R Set value +1 +0.1% -1 0.1% Specifications Set range Normal ± 1.0% 1 - 99 (6) Sub scanning direction (scanning direction) magnification ratio adjustment (SIM 48-1, SIM 48-5) a.
4) After completion of warming up, shading is performed and the current off-center adjustment value is displayed on the LCD. Sim50-12 ORG. CENTER 1:OC 50 2:SPF(SIDE1) 50 3:SPF(SIDE2) 50 [ 1- 99] 50 C. Image density adjustment (1) Copy mode (SIM 46-2) 1) Set a test chart (UKOG-0162FCZZ) on the OC table as shown below. 5) Enter the set value and press the start key. The set value is stored and a copy is made.
[7] SIMULATIONS Main code 22 1. Entering the simulation mode Perform the following procedure to enter the simulation mode. [#] key [ ] key [C] key [ ] key Main code [START] key Sub code [START] key 2. Canceling the simulation mode When the [CA] key is pressed, the simulation mode is cancelled. When the interruption key is pressed, the process is interrupted and the screen returns to the sub code entering display.
Main code 43 44 46 48 49 50 51 53 61 63 64 65 Sub code 01 02 03 04 12 13 01 Contents Fusing temperature setting 1 Fusing temperature setting 2 Fusing temperature setting 3 Fusing temperature setting 4 Standby mode fusing fan rotation setting Paper interval control allow/inhibit setting Enable/Disable setting of toner density control correction 16 Toner density control data check and toner density correction quantity display 34 Transfer current setting 02 Copy density adjustment (600dpi) 10 Copy expo
4. Contents of simulations Main code Sub code 01 01 Contents Mirror scanning operation Used to check the operations of the scanner unit and its control circuit. Enter the number of times and the magnification ratio, and press [OK] key to operate the scanner unit. The speed is variable according to the specified magnification ratio. The number of scanning can be specified by entering a value to the right lower section of the LCD.
Main code Sub code 02 01 Contents Remark Single Paper Feeder(SPF)/Reversing single pass feeder(RSPF)aging Used to check the operations of the SPF/RSPF unit and its control circuit. Enter the magnification ratio and press[OK] key or [START] key to drive the SPF/RSPF unit at the speed corresponding to the setting. (Magnification ratio selection window) Select the scan magnification ratio (drive speed).
Main code Sub code 02 08 Contents Remark SPF/RSPF paper feed solenoid operation check Used to drive the SPF/RSPF paper feed solenoid (PSOL) 20 times in the cycle of 500msec of "ON" and 500msec of "OFF." After completion of the process, the machine returns to the sub code input window. (Initial window) Sim2-8 SPUS CHECK (Only when the SPF/RSPF is installed.
Main code Sub code 03 03 Contents Remark Shifter operation check Japan only Used to reciprocate the shifter 4 times. During execution, the status of the shifter HP sensor is displayed on the right upper section of the screen. (When the sensor is detected, the display is highlighted.) [CA] key: Exits the simulation mode. [INTERRUPT] key: Returns to the sub code input window.
Main code Sub code 05 01 Contents Remark Operation panel display check Used to check the operations (ON, display) of the LED and the LCD on the operation panel. When this simulation is executed, all LED's on the operation panel (including 7SEG) are lighted and checking LCD is started. For the operation check of LCD, the area is divided into two sections; upper section and lower section, and Dark Light Off is repeated in each section.
Main code Sub code 05 02 Contents Remark Fusing lamp and cooling fan operation check Used to check the operations of the heater lamp and the cooling fan and the peripheral circuits. When this simulation is executed, the following initial menu is displayed. (Initial window) Sim5-2 HT LAMP (Execution window) Sim5-2 HT LAMP [OK] key or [START] Key PRESS OK KEY EXEC EXEC When this simulation is executed, the fusing lamp repeats ON/OFF 5 times in the cycle of 500ms.
Main code Sub code 07 01 Contents Remark Warm-up display and aging with jam detection Used to measure the warm-up time and execute aging with jam detection. When this simulation is executed, the following warm-up window is displayed. The time required for starting the warm-up and completing the initializing operation and shifting to the standby state is displayed. After completion of warm-up, press [CA] key to exit the simulation mode, allowing normal copy operations.
Main code Sub code 08 02 Contents Remark Main charger output (Grid = HIGH) Used to check the main charger output. When this simulation is executed, the following execution start window is displayed. When [OK] key or [START] key is pressed, the main charger is turned on for 30 sec in the grid voltage HIGH mode. After completion of the process, the machine returns to the sub code input window.
Main code Sub code 09 01 Contents Remark Duplex motor forward rotation check Used to check the duplex motor rotation. The duplex motor is rotated in the normal direction (paper exit direction) for 30sec. After completion of the process, the machine shifts to the sub code input window. (Execution start window) Sim9-1 DMF CHECK (Execution is not allowed when DUPLEX setting is OFF.
Main code Sub code 10 - Contents Remark Toner motor operation Used to check the operation of the toner motor. When this simulation is executed, the following execution start window is displayed. Press [OK] key or [START] key, and the toner motor is rotated for about 30sec. After completion of the process, the machine shifts to the sub code input window.
Main code Sub code 22 01 Contents Counters display Sim22-1 COUNTER 1/4 TOTAL :nnnnnnn MAINTE :nnnnnnn DEV :nnnnnnn(*) DRUM :nnnnnnn key key Sim22-1 COUNTER 2/4 CPY JOB : nnnnnnn PRT JOB : nnnnnnn SCN JOB : nnnnnnn OC SCN : nnnnnnn key key Sim22-1 COUNTER 3/4 SPF : nnnnnnn DUPLEX : nnnnnnn OTHERS : nnnnnnn MNTCYC : nnnnnnn key Counter display TOTAL : Total counter MAINTE : Maintenance counter DEV : Development counter DRUM : Drum counter CPY JOB : Copy job counter PRT JOB : Print job counter SCN
Main code Sub code 22 07 Contents Remark System setting code display Used to display the system setting code. Sim22-7 SYSTEM SYS CODE: nnnnn 09 Paper feed counter display Used to display the paper feed quantity of each paper feed tray. This simulation shows the use frequency of each paper feed section. [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window. key, key: Switches to another page.
Main code Sub code 22 15 Contents Remark Trouble memory display The latest 20 troubles are displayed. (The oldest one is overwritten sequentially.) [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window. key, key: Switches to another page. Sim22-15 TROUBLE 1/2 XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX Sim22-15 TROUBLE 2/2 XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX XX-XX key key The display sequence is as shown below.
Main code Sub code 24 05 Contents Remark Duplex print counter clear (Execution is not allowed when DUPLEX setting is OFF.) Used to clear the duplex print counter. Sim24-5 COUNTER CLR DUPLEX COUNTER CLEAR AER YOU SURE? EXEC [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window. 06 Paper feed counter clear Used to clear the paper feed counter data in each paper feed section.
Main code Sub code 24 10 Contents Remark FAX-related counter clear Used to clear the current FAX send/receive counter value (number of pages of send/receive), the accumulated time of send/receive, and the print counter to 0. Sim24-10 CLR COUN. CLEAR FAX COUNTER 1:SEND 2:RECEIVE (1 - 3) X Sim24-10 CLR COUN. CLEAR FAX COUNTER 3:PRINT PAGE (1 - 3) X CA key : Simulation cancel Interrupt key : Sub code input window [1] key [2] key [3] key [OK] key [OK] key [OK] key Sim24-10 CLR COUN.
Main code Sub code 25 01 Contents Remark Main motor operation check (Cooling fan motor rotation check) When [OK] key or [START] key is pressed, the main motor (as well as the duplex motor in the case of the duplex model) is rotated for 30 sec. If the developing unit is installed to save toner consumption at that time, the developing bias, the main charger, and the grid are also outputted. In addition, since laser discharge is required when the motor is stopped, the polygon motor is also operated.
Main code Sub code 25 10 Contents Remark Polygon motor operation check When [OK] key or [START] is pressed, the polygon motor is rotated for 30sec. (Execution start window) Sim25-10 LSU CHECK (Execution window) Sim25-10 LSU CHECK [OK] key or [START] Key PRESS OK KEY EXEC EXEC After completion of the process, the machine shifts to the sub code input window. [CA] key: Exits the simulation mode. [INTERRUPT] key: Interrupts the output operation, and shifts to the sub code input window.
Main code Sub code 26 03 Contents Remark Auditor setting Default: 0 Used to set the auditor. Sim26-3 AUDITOR SET 0 1:AUDITOR 0=P10 1=VENDOR 2=OTHER 0 [ 0-2] Code: Mode 0 : Built-in auditor mode 1 : Coin vendor 2 : Other * When the coin vendor mode is selected: 1. Sort auto select is OFF. 2. For Japan, the duplex copy use inhibition setting is ON (inhibited). 3.
Main code Sub code 26 06 Contents Destination setting Used to set the destination of the main unit. When this simulation is executed, the code number of currently set destination is displayed. Sim26-6 DESTINATION 0 1:DESTINATION 0=JAPAN [ 0-6] 0 Remark Default: Differs depending on each destination.
Main code Sub code 26 20 Contents Remark Job separator paper exit mode setting Default: 0 Used to set the paper exit mode of the job separator. * The purpose is to allow the simplified check when the job separator option is installed. It is valid only during the adjustment simulation. Without installing a printer or a FAX machine, paper is discharged to the upper stage to check if there is no problem or not.
Main code Sub code 26 31 Contents Auditor mode exclusive setup Remark Default: 1 Used to set whether paper feed is allowed from the manual paper feed tray of not when the auditor is set to the coin vendor mode.
Main code Sub code 26 42 Contents Remark Transfer ON/OFF timing control setting Default: 38 (TC ON) Used to set the ON/OF timing of the transfer charger (TC) individually. Select an item to be changed with the 50 (TC OFF) arrow keys, and change the set value to a desired value, and press [OK] key or [START] key. The entered value is saved to the EEPROM and the machine shifts to the sub code input window.
Main code Sub code 26 51 Contents Remark Copy temporary stop function setting Default: 1 Used to set whether copying is stopped temporarily when the paper exit tray full is detected. When the electronic sort function is used, paper exit of 250 sheets (*1) or more can be used for one copy job. If, at that time, copying (paper discharge) is continued with the tray full, a paper exit jam may occur. To avoid this, copying is temporarily stopped by this setting.
Main code Sub code 26 69 Contents Remark Toner near end environment setting (Function) This simulasion is used to set the operating conditions for toner near end. The setting mode is switched by [Density select] key. The set value of the selected mode is displayed on the LCD display. When the code number is entered and [START] key is pressed, the setting is switched.
Main code Sub code 41 01 Contents Remark Document size detection photo sensor check Used to check the operation of the document sensor. When this simulation is executed, the status of the document sensor is displayed. An active sensor display is highlighted.
Main code Sub code 42 01 Contents Remark Developing counter clear Used to clear the developing counter. When this simulation is executed, the confirmation window is displayed to confirm to clear or not. To clear, press [OK] key or [START] key. Not to clear, press [INTERRUPT] key or [CA] key to exit the simulation mode. Sim42-1 COUNTER CLR DEVELOPER COUNTER CLEAR ARE YOU SURE? EXEC [CA] key: Exits the simulation mode. [INTERRUPT] key: Shifts to the sub code input window.
Main code Sub code 43 02 Contents Remark Fusing temperature setting 2 When this simulation is executed, the current set value is displayed. Every time when [ ] key is pressed, the current display value is increased. For the set value, refer to Table 1. Every time when [ ] key is pressed, the current display value is decreased. For the set value, refer to Table 1. Enter a desired set value (temperature), and press [OK] key or [START] key. The set value is caved in the EEPROM.
Main code Sub code 43 04 Contents Remark Fusing temperature setting 4 When this simulation is executed, the current set value is displayed. Every time when [ ] key is pressed, the current display value is increased. For the set value, refer to Table 3. Every time when [ ] key is pressed, the current display value is decreased. For the set value, refer to Table 3. Enter a desired set value (temperature), and press [OK] key or [START] key. The set value is caved in the EEPROM.
Main code Sub code 43 13 Contents Remark Paper interval control allow/inhibit setting Default: 0 Used to change the paper feed timing of 21st sheet or later to A3 or WLT (depending on the destination setting) when in multi copy/print of narrow width sheets. When this simulation is executed, the current set number is displayed. Enter a code number and press [START] key. The entered number is saved in the EEPROM and the machine returns to the sub code input window.
Main code Sub code 44 34 Contents Remark Transfer current setting Default: NML F: 22 Used to set the transfer current value. When this simulation is executed, the list of modes and the current set NML R: 21 value are displayed on the LCD. SML F: 22 SML R: 21 Sim44-34 TC ADJ. Sim44-34 TC ADJ. BYPASS: 22 1:NML F 2:NML R 3:SML F 1/2 [ 9- 36] 22 21 22 22 4:SML R 5:BYPASS 21 22 2/2 22 [ 9- 36] Select a set item with the arrow keys and enter a set value with numeric keys.
Main code Sub code 46 10 Contents Remark Copy exposure level adjustment, individual setting (Text) 600dpi The value on the example (50) is not Used to adjust the shift amount and the slanting value for each density level (1-5) when the exposure model the default value. is TEXT (including TS). • For the shift amount, the gamma (gradation) is common. The whole sections are made brighter or darker. When the shift amount is increased, the brightness is decreased.
Main code Sub code 46 11 Contents Remark Copy exposure level adjustment, individual setting (Photo) 600dpi The value on the example (50) is not Used to adjust the shift amount and the slanting value for each density level (1-5) when the exposure model the default value. is PHOTO (error diffusion and dither). • For the shift amount, the gamma (gradation) is common. The whole sections are made brighter or darker. When the shift amount is increased, the brightness is decreased.
Main code Sub code 46 12 Contents Remark Density adjustment in the FAX mode (Collective adjustments) Used to adjust the density in the FAX mode to "AUTO" or "0" - "99".
Main code Sub code 46 13-16 Contents Sim46-15 ':2 .'8'. Sim46-15 ':2 .'8'. U-FINE 3:MANUAL(PHOTO ON) 4:MANUAL(PHOTO OFF) (1㧙 ) X U-FINE 1:AE(PHOTO ON) 2:AE(PHOTO OFF) (1㧙 ) X After input 1 - 4 After input 1 - 4 [OK] key [OK] key Sim46-15 ':2 .'8'. Sim46-16 ':2 .'8'. S-FINE AE PHOTO ON XX (2DIGITS) YY XX: Adjustment value of current state YY: Inputted adjustment value U-FINE AE PHOTO ON XX (2DIGITS) YY [OK] key [OK] key Sim46-15 ':2 .'8'.
Main code Sub code 46 20 Contents Remark SPF/RSPF exposure correction (Only when the SPF/RSPF is installed.) Used to set the exposure correction amount in the SPF/RSPF mode. (Since a slightly darker image is outputted in the SPF/RSPF mode compares to the OC mode, the difference from the OC mode is corrected with this simulation. When, therefore, the exposure in the OC mode is corrected, the SPF/RSPF exposure is Default: 50 also changed accordingly.
Main code Sub code 46 30 Contents Remark AE limit setting Default: 196 Used to set the limit value in AE and AE (toner save) mode. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.
Main code Sub code 46 39 Contents Remark FAX IMAGE adjustment Used to adjust the resolution and the filer in the FAX mode. The current set value of each resolution is displayed. 1:STD. 2:FINE 3:S-FINE (1 - 7 ) Sim46-39 FAX IMAGE Sim46-39 FAX IMAGE Sim46-39 FAX IMAGE 4:U-FINE 5:FINE/HT 6:S-FINE/HT (1 - 7 ) 1 1 1 X 1 1 1 X 7:U-FINE/HT 1 (1 - 7 ) X 1 - 7 input [OK] key Specify a resolution to be set. [BACK] key Sim46-39 FAX IMAGE STD.
Main code Sub code 48 05 Contents Remark SPF/RSPF mode sub scanning magnification ratio adjustment in copying Used to adjust the sub scanning magnification ratio in the SPF/RSPF mode. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.
Main code Sub code 49 01 Contents Remark Flash Rom program writing mode (MCU) Used to download the programs and data sections of the main unit MCU board, the FAX board, and the operation panel. When this simulation is executed, the machine immediately shifts to the download mode and the following display is shown. (When entering the download mode) (Receiving download data) Download Data Receiving. Download Mode. Processing finished. Turn off the power.
Main code Sub code 49 01 Contents Remark FAX 0xFF 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x11 0x12 0x21 0x22 0x23 0x24 0x25 0x31 0x32 0x33 0x34 0x35 0x41 0x42 0x43 02 No process OK Download impossible Total data size error LOADER no file DWLD no file BOOT no file MAIN no file FONT download impossible Option FLASH connection error Option FLASH no match LOADER data size error LOADER work sum check error BOOT data size error BOOT work sum check error BOOT Flash erase error BOOT Flash write e
Main code Sub code 50 01 Contents Remark Image lead edge adjustment Used to adjust the following items related to the lead edge adjustment. 1.Print start position (Offset between output image and paper Adjusted for each tray.) 2.Image lead edge void (Margin on the output image lead edge) 3.Document scanning start position (Image scanning start position in the sub scanning direction) When this simulation is executed, the selection window of the adjustment items and the set value are displayed.
Main code Sub code 50 01 Contents Remark (Adjustment procedure) (1) Set the print start position (1: TRAY1), the lead edge void amount (4: DEN - A), and the scanning start position (5: RRC - A) to "1" and make a copy of 100%. (2) Measure the image loss amount (R mm) of the scale. Set [5:RRC - A] = 10xR(mm). (Example. Set 40.) When the value of [5: RRC - A] is increased by 10, the image loss is decreased by1mm.
Main code Sub code 50 08 Contents Remark FAX lead edge adjustment (scan) Used to adjust and set the FAX document scan lead edge position and scan and print the document.
Main code Sub code 50 10 Contents Remark When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy execution window. After completion of copying, the machine returns to the adjustment value input window. When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and performs copying. (Copy start window) Ready to copy.
Main code Sub code 50 18 Contents Remark Memory reverse position adjustment in duplex copy Used to adjust the reverse point (scanning end position) on the reversed surface in duplex copy. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed (Adjustment item selection window) Display text array : Adjustment mode Sim50-18 DUP REV.
Main code Sub code 50 19 Contents Remark Rear edge void adjustment in duplex copy Used to adjust the rear edge void amount in duplex copy. When this simulation is executed, the selection window of the adjustment items and the current set value are displayed.
Main code Sub code 51 02 Contents Remark (*1) Valid only when an option is installed. (If an option is not installed, it is not displayed on the adjustment window.) (*2) When heavy paper slips in manual feed copy, or when a paper jam occurs in thin paper copy, adjust this set value to remove the problem. •Heavy paper slips. • Thin paper jams. Increase the set value. Decrease the set value. The adjustment range is 1 - 99.
Main code Sub code 61 02 Contents Remark Laser power correction ON/OFF (Invalidity) Enable/Disable of the LSU laser power correction during the operation is set. When [START] key is pressed, the entered set value is saved and the machine enters the sub code input standby mode. Sim61-2 LASER PWR 1:LASER POWER 1 [ 0 - 1] 1 Code number : Mode 0 : Correction Enable 1 : Correction Disable Note: Changing the setting does not affect the operation.
Main code Sub code 64 01 Contents Remark (*1) The grid pattern of about 1cm square is outputted. Data are always made for A3 size. If printing is made on paper smaller than A3, the remaining data are not outputted. (Images are not formed on the drum.) (Initial window) Ready to copy. S Copies in progress.
Main code Sub code 66 02 Contents Remark FAX soft SW initializing Used to clear the FAX-related soft SW values except for the line signal adjustment value and the machine adjustment value and set them to the default values (which differ depending on the country code).
Main code Sub code 66 04 Contents Remark Signal send mode Used to send signals to the line and the machine speaker by setting the signal number. (Signal send is continued until interruption is instructed by pressing RETURN key.) The signal send level is selected from 0db and the soft SW values. Since the level setting is not required for 1:NO SIGNAL and 31:PSEUDO RNG - 33:R.B.TONE NONE, the selection menu does not appear.
Main code Sub code 66 10 Contents Remark Image memory contents clear Used to clear all the image data (including confidential receive contents) in the image memory of the FAX section. The management table is also cleared (initialized) at the same time. Sim66-10 IMAGE CLR CLEAR IMAGE MEMORY Sim66-10 IMAGE CLR [OK] key CLEAR IMAGE MEM.
Main code Sub code 66 13 Contents Remark Dial number registration Used to perform send test and adjustments of the dial pulse and the DTMF signal. Perform send test of the dial pulse and the DTMF signal, and perform adjustments of the make time of the dial pulse and adjustments of the send level of the DTMF signal.
Main code Sub code 66 21 Contents Remark FAX information print Used to print the following FAX information. Sim66-21 LIST Sim66-21 LIST 1:USER SW. LIST 2:SOFT SW. LIST 3:SYSTEM ERROR (1 - 5) X 4:PROTOCOL MONITOR 5:FAX SIMULATION After selection with numeric keys Sim66-21 LIST CAN NOT PRINT [OK] key (1 - 5) X After selection with numeric keys [OK] key After pressing [OK] key, during execution Sim66-21 LIST SOFT SW.
Main code Sub code 66 31 Contents Remark TEL/LIU setting The following bit 0/1 is alternatively switched. At the same time, the target signal name is highlighted. [CA] key : Simulation cancel [INTERRUPT] key : Sub code input window Numeric keys : Item selection [OK] key : Input value settlement and execution [START] key : Input value settlement and execution [BACK] key : Returns to the selection window keys : Page switch [C] key : Input value clear. ON when highlighted.
Main code Sub code 66 33 Contents Remark Signal detection check Used to detect signals and display the result with ON/OFF.
Main code Sub code 66 37 Contents Remark The following soft SW's are newly provided. Type of sound 1. Sound volume of call sound Sound volume of call sound (Low) Sound volume of call sound (Medium) Sound volume of call sound (High) 2. Line monitor speaker sound volume Line monitor speaker sound volume (Low) Line monitor speaker sound volume (Medium) Line monitor speaker sound volume (High) 3.
Main code Sub code 66 42 Contents Remark PIC program writing Used to write the program again into the power control which is installed to the FAX BOX. Sim66-42 PIC RELOAD ARE YOU SURE? EXEC [CA] key [INTERRUPT] key [OK] key [BACK] key 43 After pressing [OK] key, during execution Sim66-42 PIC RELOAD Sim66-42 PIC RELOAD ARE YOU SURE? OK [OK] key EXEC EXEC : Simulation cancel : Sub code input window : Settlement : Returns to the simulation code input window.
[8] TROUBLE CODE LIST 1.
Main Sub code code CE 05 06 09 Details of trouble Content FTP directory error Detail The designation of the directory in the FTP server is improper. Check and remedy Since the directory of the FTP server registered as the destination of file server send scan is improper, the scan data cannot be sent. Check to confirm that the registration of the destination is correct.
Main Sub code code E7 F2 93 40 64 F2 70 Details of trouble Content Data communication error (FAX scan) Detail When data transmission from the machine to the FAX board fails 5 times: F5 02 Details of trouble Content Copy lamp lighting abnormality Detail The copy lamp does not turn on. Cause Copy lamp abnormality Copy lamp harness abnormality CCD PWB harness abnormality. Check and remedy Use SIM 5-3 to check the copy lamp operations. When the copy lamp lights up.
Main Sub code code F6 88 99 F9 H2 00 00 01 Details of trouble Main Sub code code H3 00 Details of trouble Content FAX board communication trouble (Time out). Content Heat roller high temperature detection (MAIN) Detail FAX board communication error. Detail The fusing temperature exceeds 245C°. Cause There is no respond command from the FAX for 30sec or more. Cause Check and remedy Check connection of the FAX board. Replace the FAX board. Reset the machine (Power OFF/ON).
Main Sub code code H5 L1 01 00 Details of trouble Content 5 continuous POUT not-reached error Detail When 5 continuous not-reached jams to the paper exit sensor (POUT) occur. The jam counter is backed up and it is used in a job after turning on the power. Cause Jam paper is not removed from the fusing unit. (Jam paper remains.) Paper exit sensor breakdown or harness connection trouble Fusing unit installation trouble Check and remedy Check for jam paper remaining in the fusing unit.
Main Sub code code L8 U1 U2 01 03 04 11 U9 00 80 81 82 Details of trouble Main Sub code code U9 84 Details of trouble Content No full wave signal. Content Panel board communication trouble (Framing). Detail The zero cross signal is not detected. Detail Cause Power unit abnormality. MCU PWB abnormality. A framing error occurs in communication between the MCU and the Panel PWB. Cause Check and remedy Check connection of the harness and connectors. Replace the MCU PWB.
< Communication result code list > Result code Final reception signal (Transmitting side) Final reception signal (Receiving side) 0 Abnormal signal Abnormal signal 1 NSF, DIS (SID), (SUB), NSS, DCS 2 CFR (PWD), (SEP), NSC, DTC 3 FTT EOP 4 MCF EOM 5 PIP, PIN MPS 6 RTN, RTP PRI-Q 7 No signal, DCN DCN 8 PPR PPS-EOP 9 Result code (Communication result) Reception memory over When memory is over during reception, .
Result code (Communication result) 64 Communication report result column F code is not accepted. Communication interruption content When F code is transmitted, 1) When DCN is received for SUB, check the BOX number. 2) When DCN is received for SID, check BOX number and the pass code. When F code is received, When the F code relay broadcast function or the F code confidential reception function is inhibited with soft switches.
[9] MAINTENANCE 1. Maintenance table X:Check(Clean, adjust, or replace when required.
2. Maintenance display system Toner Life, 16K Remaining quantity check *1 a. Press and hold the density adjustment LIGHT key for more than 5 sec, and the machine will enter the user program mode. b. Press and hold the "%" key for more than 5 sec, and the remaining quantity will be displayed on the copy quantity display in one of the following levels: (Remaining quantity display levels: 100%, 75%, 50%, 25%, 10%, LO) c. Press the density adjustment LIGHT key to cancel.
[10] DISASSEMBLY AND ASSEMBLY B. Charger wire WARNING Before performing the disassembly procedure, be sure to remove the power cord to prevent against an electric shock. Installation: The spring tip must be between two reference ribs. •The charger wire must be free from twists or bending. •Be sure to put the charger wire in the V groove. No.
2. Optical section C. Inverter PWB for copy lamp (1) Note: When disassembling or assembling the optical unit, be careful not to touch the mirror and the reflector. No. Content A Table glass B Copy lamp unit C Inverter PWB for copy lamp D Copy lamp E Lens unit F Wire G Document detection (2) (1) A. Table glass (1) (1) (1) (2) (3) (1) (4) (3) (3) (2) B. Copy lamp unit Disassembly: Assembly: Adjustment: Be sure to put No. 2/3 mirror unit to the positioning plate (A).
E. Lens unit <4>Loosen the CCD unit fixing screws. Note: Do not remove screws which are not indicated in the figure. If the height of the base plate is changed, it cannot be adjusted in the market. Note: The CCD/lens unit is factory-adjusted before shipping. Since these adjustments cannot be performed in the market. Never touch the screws other than screw 2) of the CCD/lens unit. (1) (2) (1) (3) (2) (3) (4) Note:Never loosen the screws marked with X.
F. Wire • For AB series (2) (2) (3) (1) (1) (3) (1) (4) (4) (2) (3) (4) 3. Fusing section No. (2) Contents A Fusing unit B Thermostat C Thermistor D Heater lamp E Upper heat roller F Separation pawl G Lower heat roller H Separation pawl A. Fusing unit removal (1) (1) G.
B. Thermostat D. Heater lamp Assembly: Insert the spring (A) into the hole (B) in the fusing frame. (1) (2) (2) (3) (A) (1) (B) (3) (3) (2) C. Thermistor Installation: Install in direction that the sponge side (A) of the thermistor comes in contact with heat roller. Check that the thermistor is in contact with the upper heat roller. (1) (1) (2) (2) (A) (1) (3) (1) (2) (2) Assembly: Put the fusing harness (A) on the heater lamp (B) as shown in the figure and fix them together.
E. Upper heat roller Disassembly: F. Separation pawl There are three pawls on the fusing cover. Remove the screws and slide the fusing cover to the right to remove. The heater lamp is fixed on the fusing cover with a screw. Slide the fusing cover to the front and remove the screw, then remove the heater lamp. (1) (2) (3) (2) (3) (2) (2) (3) (2) (3) (1) (3) G.
Note: I apply grease (JFE552) to a fusing lower frame, lib. 4. Paper exit section No. Content A Ozone filter B Cooling fan C Paper exit unit D Paper exit sensor / duplex sensor E Transport roller F Paper exit roller G Paper exit interface PWB A. Ozone filter Grease (JFE552) (1) (2) (1) H. Separation pawl (1) (1) B.
(A) Simplex C.
D. Paper exit sensor / duplex sensor F. Paper exit roller (A) Paper exit sensor Assembly: Insert the spring pin so that the waveform (A) of the spring pin faces in the longitudinal direction of the paper exit drive gear long hole (B). Be sure to insert two ribs (C) into the groove (D). (B) Duplex sensor (1) (2) (1) (A) (3) (B) (3) (3) (D) (1) (C) (1) (2) (C) (A) (1) (2) (2) (1) (2) (B) (3) (4) E. Transport roller (4) (1) G.
5. MCU 7. LSU No. A Content No. MCU disassembly A A. MCU disassembly Content LSU unit A. LSU unit (1) Disassembly: The connector, the harness, and the screw are removed. Note: When replacing the MCU PWB, be sure to replace the EEPROM of the MCU PWB to be replaced. (1) (1) (4) (1) (2) (2) (3) (1) (2) (2) (3) (2) 6. Optical frame unit No. A Content (4) Optical frame unit A. Optical frame unit Installation: Install the optical unit in the sequence shown above.
8. Tray paper feed section/Paper transport section No. C. Paper feed clutch/Paper feed roller Content A Drive unit 3 4 2 B PS clutch/Resist roller C Paper feed clutch/Paper feed roller D Connection gear unit A. Drive unit Assembly: When assembling, be sure to check that the clutch rotation stopper is securely engaged in the frame. 1 (7) (2) (2) (6) (4) (3) (6) (5) (1) (1) (5) (1) (3) (4) D.
9. Bypass tray section No. B. Bypass tray paper feed Content A Bypass tray transport roller/Bypass tray paper feed roller B Bypass tray paper feed C Bypass tray solenoid D Bypass tray transport clutch E Bypass tray paper feed clutch F Pressure plate unit (1) (3) A. Bypass tray transport roller/Bypass tray paper feed roller (4) (2) Note: Push the lever at the right edge of the multi frame cover to the right upper side and remove it. A (5) (2) A A A A (3) (4) A (1) C.
D. Bypass tray transport clutch (1) (3) (2) (3) (1) (2) (2) (2) (3) (1) (4) Apply grease (FG-40H) to the gray area (UKOG-0004QSZZ). Apply grease (FG-40H) to the gray area (UKOG-0004QSZZ). Apply grease (FG-40H) (UKOG-0004QSZZ). E. Bypass tray paper feed clutch F. Pressure plate unit Note: Push the lever at the right edge of the multi frame cover to the right upper side and remove it.
10.Power section B. High voltage P.W.B. No. Content A Power unit B High voltage P.W.B. C Power P.W.B. D Power switch (1) (2) A. Power unit (1) (1) (1) (4) (1) (2) C. Power P.W.B. (2) (3) (1) (1) (2) (3) (2) (1) (1) (1) (2) D.
11.Developing section No. C. MG roller Contents A Developing box B Developing doctor C MG roller A. Developing box (1) (5) (4) (3) (2) (3) B. Developing doctor (3) (3) (4) (1) (3) (2) Adjustment: Developing doctor gap adjustment Adjustment: MG roller main pole position adjustment Note:Attach it to fit with the attachment reference when replacing the DV blade. Mark-off line Attaching reference 0 0.5 DV blade 0.
12.Process section No. 2. Prior exposure prevention Contents A Drum unit B Main charger unit C Cleaning blade A.Drum unit When removing the drum, put the drum unit upside down to prevent waste toner from spilling. [Note] • Avoid servicing in a place where there is strong light. • Do not expose the unit to light for a long time. • Cover the OPC drum with light-blocking material. (When using paper, use about 10 sheets of paper to block light.
13.Others No. (2) Contents A Operation P.W.B. B Tray interface P.W.B. C 2nd tray paper entry sensor / Paper empty sensor D 2nd tray transport clutch E 2nd tray transport roller F 2nd tray paper feed clutch G Main motor (1) (2) (2) (3) (1) hole H Paper entry sensor I Paper empty sensor positioning pin A. Operation P.W.B. [Note for installation] When installing, engage the hole of the LCD box unit with the positioning pin. (1) (1) (1) (1) (1) (5) (6) (5) (5) (7) (5) B.
C. 2nd tray paper entry sensor / Paper empty sensor Disassembly: E. 2nd tray transport roller When the second paper feed unit is detached, the screw is removed, and the main body is lifted. (4) (3) (1) (1) (2) (5) (1) (2) (3) F. 2nd tray paper feed clutch (1) (3) (4) (2) D. 2nd tray transport clutch G.
H. Paper entry sensor (1) (1) (2) (3) I.
[11] OPERATIONAL DESCRIPTIONS 1. Paper feed operation • When copy/print movement is started, a main motor is a timing of the rotary (drive system) paper pickup, and a paper feed clutch does ON, and a paper feed roller turns. • A transportation clutch does ON, and the paper is sent to the transportation department. * By a separation plate to prevent against double feed of paper.
[12] FLASH ROM VERSION UP PROCEDURE 1. Preparation 3) PC side: Boot the maintenance program. Select the model icon. Write the download data (the file with the extension dwl) to the main body. Necessary files for download • Maintenance.exe (Maintenance software) • ProcModelH.mdl.SE • ProcModelH.ini.SE • ProcModelH.fmt.SE • SFAXNoXXX.fld • Mainte.inf • Usbscan.sys • Download file:***.dwl •The Download file(***.
7) PC side: Double click "Special (MCU/Panel/Facsimile)" in the main tree item to develop the sub tree items, and double click "DWL Download" in the sub tree items. 11) Main body side: Wait until the word "Processing finished.Turn off the power." appears on the operation panel. The appearance of "Processing finished.Turn off the power." indicates the completion of the download (writing into ROM). Turn the power off and the USB cable can be removed at this point.
3. Version confirming procedure 1) Main body side: Executable by performing the Service Simulation No. 49-01 (Flash Rom program-writing mode). (A word "Download mode." appears on the operation panel to denote the download mode status. ) 6) PC side: Confirm a tree is displayed under the "Special (MCU/Panel/ Facsimile)" on the maintenance program". (If no tree is displayed, confirm that the USB is connected and select the "Reconnect" (the above 5) again.
4. Facsimile Data upload procedure 1) Main body side: Executable by performing the Service Simulation No. 49-01 (Flash Rom program-writing mode). (A word "Download mode." appears on the operation panel to denote the download mode status. ) 6) PC side: Confirm a tree is displayed under the "Special (MCU/Panel/ Facsimile)" on the maintenance program". (If no tree is displayed, confirm that the USB is connected and select the "Reconnect" (the above 5) again.
9) PC side: The following message is displayed, and uploading the FAX data is started. 5. Updating the MX-NB12 firmware A. Preparation Write the firmware (file with extension of brn) into the MX-NB12. Necessary items for updating • *.brn (Firmware) • USB memory Caution: The firmware (*.brn) must be copied to the root directory in the USB memory in advance. 10) PC side: When the message below is displayed, upload is completed. Completion message: Upload is completed.
6. Installation procedure A. USB joint maintenance program installation 5) Select the folder which includes the maintenance tool driver (Mainte.inf), and press the OK button. (When the driver is included in the "C:\Sirius" folder:) The driver is installed by plug and play. B. Installation procedure on Windows XP 1) Machine side: Executable by performing the Service Simulation No. 49-01 (Flash Rom program-writing mode). (A word "Download mode.
C. Installation procedure on Windows 2000 1) Machine side: Executable by performing the Service Simulation No. 49-01 (Flash Rom program-writing mode). (A word "Download mode." appears on the operation panel to denote the download mode status.) 6) Press the "Browse" button. Specify the folder which includes the maintenance tool driver (Mainte.inf) 2) Connect the machine and the PC with a USB cable. 3) Check that the new hardware search wizard is shown. Press the NEXT button.
[13] IP ADDRESS SETTING 1. Setting the ip address of the machine by system settings Set the IP address of the machine in the system settings. The procedure for selecting a system setting is explained in "SELECTING A SETTING FOR A SYSTEM SETTING" in the Operation Guide for the machine. A. Enabling/disabling DHCP C. Setting/changing the ip address manually This is used to set Enable/Disable of DHCP (Dynamic Host Configuration Protocol).
MX-M182 ELECTRICAL SECTION 14-1 Dup model only CPU INTERRUPT SPPD CPU I/O RTH DRST Other Inputs SDRAM 128MB Toner Motor Mirror Motor Driver LSU SPFCLH SPFPSOL 2Mb(128k*16bit) D[15…0] A[19…1] Reset IC Driver Driver 24V /POFF, HL, PR FW 5V, 24V POWER SUPPLY 5V TC, GRID, MC, BIAS HVU PMCLK CPU CLK (16 - 20cpm : 2078.74Hz (24.576MHz) 23cpm : 2881.
MX-M182 ELECTRICAL SECTION 14-2 HEATER LAMP VLP-02V VLR-02V 20 HL HARNESS MAIN MOTOR HARNESS CASSETTE SW HARNESS CASSETTE EMP HARNESS DEV HARNESS CRM-MCU HARNESS GP1A73 3 HANDEMP harness GP1S58 3 B4B-PH (White) HAND SOLENOID HARNESS PICK UP SOL D2X 2 3 GP1S73 PAP-02V-S PALR-02V 3 B22B-PUDSS-1 (White) B12B-PASK (White) PS HARNESS LSU-MCU HARNESS SIDE COVER SW HARNESS OPTION COIN VENDER AUDITOR OPTION 1st TRAY OR 2nd TRAY OR MULTI CASSETTE Japan only Cassette dehumidifier heater
MX-M182 ELECTRICAL SECTION 14-3 HAND PAPER PICK UP SOL CASETTE SWITCH CASETTE EMPTY SENSOR PAPER IN SENSOR HAND PAPER EMPTY SENSOR PWB Jaguar 3 MOTOR NEW B05B-PASK 5 4 3 2 1 175767-3 RD 3 WH 1 BL 2 179228-3 PK BL GY PAP-05V-S PAP-02V-S 1 24V 2 /HPSOL PALR-02V 1 2 15778-2 BL 1 (CASETTE) GY 2 DGND 179228-2 175767-3 RD 3 5Vp-off WH 1 (CPEMPTY) BL 2 DGND 179228-3 5Vp-off (PIN) DGND 1 5Vp-off 2 (HPEMPTY) 3 DGND Soldering /MMCLK /MMRDY /MMD PGND INT24V XHP-2-BK OR PL DHAI-0557QSPZ
MX-M182 ELECTRICAL SECTION 14-4 FOR FAX MODEL SCAN9 SCAN5 SCAN8 SCAN7 SENSE6 SCAN6 SENSE4 SENSE5 SCAN4 SCAN3 SCAN2 SCAN1 SCAN0 /FAXSW /FAXOPD DGND FAX-KEYCN1(9610S-16C) PWB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CN1(9610S-28C) 1 DGND H_LED 2 3 LED2 4 ST_LED 5 SCAN8 6 SCAN1 7 SCAN2 8 SCAN5 9 SCAN3 10 ST_KEY 11 SENSE3 12 SENSE2 13 SCAN6 14 SCAN4 15 SCAN7 16 SENSE1 17 SENSE0 18 SCAN0 19 LED5 20 LED4 21 LED3 22 LEDSI 23 LEDCLK 24 /LEDLATCH 25 /LEDENABLE 26 LED1 27 3.
MCU PWB 1 2 3 EHR-4 VHR-3N RD RD MX-M182 ELECTRICAL SECTION 14-5 OR LB PK GY CN128(B04B-PASK-1) 2 (SDA_CRUM) 3 (SCL_CRUM) 1 VCC3 4 DGND VHR-2N CN131(B2P-VH) BK 1 TMA_O BK 2 TMB_O RD PL BR GY CN126(B4B-PH-K-S) 1 24V 2 (TCS) 3 (DVS1) 4 PGND DHAI-0322QSZZ THERMOSTAT OR LB PK GY RD PL BR GY #250 CN1(B07B-PASK) 1 /MC 2 /TC 3 GRIDL 4 BIAS 5 PGND 6 INT24 7 (TCCNT-AN) DV UNIT TONER MOTOR OR DHAI-0566QSPZ Side Cover SW Front Side Cover SW RD WH WH DHAI-0108QSPZ
CN110(DBR40-251F100) 1 24V 2 24V 3 SPMT3# 4 SPMT2# 5 SPMT0# 6 (SELIN3B) 7 (SELIN2B) 8 (PDOWNA) 9 SPFRSOL 10 SPFPSOL 11 PGND 12 DGND 13 DGND 14 PGND 15 (YSPF) 16 (/SPFCOVER) 17 SPMT1# 18 (SPFOPEN) 19 (/SPFPOUT) 20 (SELIN1B) 21 SPFCLH 22 SPFGSOL 23 (PDOWNB) 24 5V 25 (SPFPAPER) MCU PWB D-SABU25PIN DHAI-0559QSPZ PUDP-26V-S-1 CN5(B26B-PUDSS) 8 N.
MX-M182 ELECTRICAL SECTION 14-7 D-GND DRS1 5V D-GND CSS1 5V DRS1 CSS1 CSS2 PPD2 CASS2 LOWER UN UPPER UN DF3A-3P-2DS DF3-3S-2C 1 2 3 D-GND CSS1 5V DRS1 CSS1 FSCL2 D-GND CSS2 5V D-GND PPD2 5V 6 7 8 3 4 5 SMR-02V-N SMP-02V-NC 1 1 24V 2 2 /PSCL2 SMR-02V-N SMP-02V-NC 1 1 24V 2 2 /FSCL2 6 7 8 DF3A-3P-2DS DF3-3S-2C 1 D-GND 2 CSS2 3 5V PSCL2 3 4 5 5 4 3 2 1 6 PPD1 5V CSS1 DRS1 N.C N.C N.C N.C N.C N.C N.C N.
MX-M182 ELECTRICAL SECTION 14-8 CN005 (B2P3-VH-LF) 3 LIVE 2 N.C. 1 NEUTRAL PS PWB VHR-3N WH PAP-12V-S VHR-3N For EMI ClassA DHAI-0663QSPZ For EMI ClassB DHAI-0703QSPZ OP-PS HARNESS(SIR) PAP-10V-S BK MCU PWB CN140 (B10B-PASK-1) 1 GND 2 UAT_RXD_1 3 UAT_CTS_1 4 UAT_RTS_1 5 UAT_TXD_1 6 nCNCT 7 RESET 8 nPOF 9 nWAKEUP 10 GND DHAI-0661QSPZ MCU-NNB HARNESS CN100(B2P3-VH-LF) 1 LIVE 2 N.C. 3 NEUTRAL CN200(B02P-VH-LF) 1 +5V 2 SGND 2 1 SMP-02V-NC OP PS PWB 2 1 SGND +5V USB_D+ USB_DGND VBUS USB2.
MCU PWB CN500 80P-JMDSS-G-1-TF 1 DGND 2 DGND 3 IO3.3 4 IO3.
Memo
Memo
LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: Lead-Free 5mm Solder composition code (Refer to the table at the right.
CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer’s instructions.
COPYRIGHT © 2011 BY SHARP CORPORATION All rights reserved. Produced in Japan for electronic Distribution No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic; mechanical; photocopying; recording or otherwise without prior written permission of the publisher. Trademark acknowledgements • Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.