MD/CD STEREO OPERATION MANUAL MD-X8

ManualsBrandsSharp ManualsStereo SystemMD-X8

0048

MINIDISC OPERATION

H Loading and playing MiniDiscs

1 Press the MD H button.

I The power will be turned on automatically,and the unit will enter the

MD playback mode.

2 Load a recorded MiniDisc in the direction indicated by the

arrow on the MiniDisc, with the labeled side facing up.

I The total number of tracks and the total disc playing time will be

displayed. At this time, the MD indicator will light.

3 Press the MD 06 button.

I The MD playback indicator will light and playback will begin from track

1on the disc you have specified.

I When the last track has been played back, this unit will stop automati-

cally.

To interrupt playback:

Press the MD06 button.

I The MD playback indicator will flash.

I Press the MD06 button to resume playback from the same point.

To stop playback

Press the MD H button.

To remove a MiniDisc:

Press the 7 button.

I The MiniDisc will be ejected.

Notes:

I Although vibration will not normally cause a MiniDisc to skip, you may

hear a skip in the sound if there is continuous vibration.

I When you listen to MiniDiscs near a radio or a TV set, the radio or the

TV set may pick up noise.

Keep the unit as far away as possible from tuners.

I When a optionally available sound card is used, an MD inserted in this

product can be played from a personal computer.

Direct playback

If a MiniDisc is loaded in the unit, pressing the MD 06 button

turns the power on, and begins playback.

After use:

Press the POWER button to turn the power off.

Note:

I The power cannot be turned off while reading the information on a

MiniDisc.

I If no disc and track names have been recoded on an MiniDisc, they

will not appear on the display.

MD indicator

Total number

of tracks

Total playing time

Disc name Track name

3 W FORWEVERWWWWWWWW

2 WWAV EWWWWWWWWWWWW

1 W LOVEWSONGWWWWWWW

BESTWHITSWWWWWWWWWWWW

MDWWW 12WWW 55:08WTOTAL

Cautions:

I Do not carry the unit with a disc left in a disc tray. The disc may

come loose inside the unit and be damaged or cause damage

to the unit. This may also cause malfunctions.

I If you press the CD

button, one of the CD PLAY buttons (1-3)

on the main unit or remote control, or any of the CD 7 buttons while

the disc tray is open, the disc tray will close automatically. Therefore,

be careful not to get your fingers caught in the disc tray.

I Do not place two CDs in one disc position.

I Do not push the disc tray while it is moving.

I If the power fails while the tray is open, wait until the power is

restored before trying to close it.

I If the disc tray is stopped forcibly, “ERROR” will appear on the

display and the unit will not function.

If this occurs, turn the power off, and turn it on again.

I If TV or radio interference occurs during CD operation, move the unit

away from the TV or radio.

I If the disc is damaged, dirty, or loaded upside down, the disc will be

skipped and the next disc will be automatically played.

I If the main unit is subjected to a sharp jolt or it is used where

vibrations are present, sound dropouts may occur. Use the unit in a

stable environment.

I If the volume is set to too high, a dropout may occur due to vibrations

from the speakers. If this happens, move the main unit away from the

speakers or turn down the volume.

I Do not use CDs with loose cellphane tape or stickers or CDs which

have glue left on the surface from tape or stickers. If such a CD is

inserted, you may not be able to remove the CD or the unit may

cause malfunction.

MINIDISC OPERATION

(Continued)

MD playback indicator

MD indicator

*17-21 98.6.23, 0:11 PM18