Service manual

– 10 –
MD-MT80W/90W/90/90C
Error Messages
ERROR MESSAGES MEANING REMEDY
BATT EMPTY
●
The battery is run down.
●
Charge the rechargeable battery or replace the al-
kaline battery (or use the AC adaptor for power).
BLANK MD
●
Nothing is recorded.
●
Replace the disc with a recorded disc.
Can't COPY
●
You tried to record from a copy prohibited
MiniDisc.
●
Record using the analog cable.
Can't EDIT
●
A track cannot be edited.
●
Change the stop position of the track and then edit it.
Can't READ (*)
●
The disc data cannot be read because the
disc or unit is damaged.
●
Reload the disc.
●
Replace it with another recorded disc.
Can't REC
●
Recording cannot be performed correctly
due to vibration or shock.
●
Re-record or replace it with another recordable
disc.
Can't STAMP
●
Stamp function does not work.
●
Check the number of tracks.
Can't WRITE
●
Cannot save the TOC information correctly
to a MiniDisc. (A large portion of the disc has
been damaged.)
●
Replace the disc with another recordable disc.
DEFECT
●
The disc is scratched.
●
If the sound you hear is not right, record again.
●
Replace the disc with another recordable disc.
DISC FULL
●
The disc is out of recording space.
●
Replace it with another recordable disc.
Er-MD (**)
●
The microprocessor has reported a system
fault and the unit is out of order.
●
To have it repaired, go to the distributor where you
purchased the unit.
HOLD
●
The unit is in the hold mode.
●
Cancel the hold mode.
LOCKED
●
You removed a MiniDisc while recording or
editing.
●
Turn off the power and remove the MiniDisc.
NO DISC
●
A disc has not been loaded.
●
Load a disc.
Number or symbol appears in (*) position. (Refer to P.29)
NO SIGNAL
●
Poor connection of the digital cable.
●
Connect the digital cable securely.
●
No output signal comes out from the
connected unit to playback.
●
If the portable CD player has a function to prevent sound
skips, deactivate it.
●
The input signal has improper sampling
frequency.
●
Playback with the connected unit.
NOT PLAY
●
You tried to play back a track that can-
not be played with this equipment.
●
Play back another track.
PLAY MD
●
You recorded on a playback-only disc.
●
Replace it with a recordable disc.
POWER ?
●
Improper power is being supplied.
●
Use one of the specified power sources.
PROTECTED
●
The write protection tab of a MiniDisc is
set to the protected position.
●
Move the write protection tab back to its original posi-
tion.
●
You tried to record on a playback-only disc.
●
Replace it with a recordable MiniDisc.
SORRY
●
Since a track number is currently being
located or updated, the unit cannot ac-
cept your command.
●
Wait for a while and try the operation again.
TEMP OVER
●
The temperature is too high.
●
Turn off the power, and wait for a while.
TOC FORM (**)
●
There is an error in the recording signal.
●
Erase all of the tracks, and then record again.
TOC FULL
●
There is no space left for recording
character information (track names,
disc names, etc.).
●
Replace it with another recordable disc.
Tr. Protect
●
The track has been protected from be-
ing erased.
●
Edit the track with the device on which it was recorded.
? DISC
●
A disc which contains data other than
music was played.
●
A disc which contains non-music data cannot be played.
●
There is an error in the signal recorded
on the disc.
●
Replace it with another recorded disc.
Number or symbol appears in (*) position. (Refer to P.29)