MD-MS200W/MD-MS200/MD-MS200H SERVICE MANUAL No. S4724MDMS200W MD-MS200W MD-MS200 MD-MS200H • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS Page SAFETY PRECAUTION FOR SERVICE MANUAL (MD-MS200H ONLY) ............................................................................ 2 BATTERY DISPOSAL (FOR MD-MS200 ONLY) .......................................................................................
MD-MS200W/MD-MS200/MD-MS200H SAFETY PRECAUTION FOR SERVICE MANUAL (MD-MS200H ONLY) Precaution to be taken when replacing and servicing the Laser Pickup. The AEL (Accessible Emission Level) of Laser Power Output for this model is specified to be lower than Class I Requirements.
MD-MS200W/MD-MS200/MD-MS200H BATTERY DISPOSAL (FOR MD-MS200 ONLY) Contains nickel cadmium (or sealed lead) battery. Must be recycled or disposed of properly. Remove the battery from the product and contact federal or state environmental agencies for information on recycling and disposal options. FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL.
–4– Notes: After charging has been completed, the AC adaptor may be left connected. (Charging at night.) The battery will not be charged whilst the main unit is operating. If the AC adaptor is removed from the main unit or from the AC socket whilst charging, “ ” will not disappear for about 1 minute. This is normal. ing. “ ” will appear, and the battery will begin charging. Battery charging will be complete in 3 hours. When battery charging begins, “ ” will be displayed.
For MiniDiscs on which repeated recording and editing were performed, some sounds may be skipped whilst cueing and reviewing. If there are scratches or dust on a MiniDisc, the track numbers following that track will be increased by one. A track number can be created in the middle of a track. For MiniDiscs on which repeated recording and editing operations were performed, the COMBINE function may not work. Two tracks may not be combined in editing.
Press the n OFF button to turn off the power (which will finish writing the information on the disc). Slide the accidental erase prevention tab back to its original position. Connect the unit properly to the other equipment. Plug in the AC adaptor. Move the HOLD switch to turn off the safety mode. The track number or character information has not been written on the disc. The unit is in the recording or editing mode.
MD-MS200W/MD-MS200/MD-MS200H DISASSEMBLY (A1) x2 Ø2x2mm Caution on Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Take the battery and minidisc out of the unit. 2. When disassembling the machine, be sure to withdraw the power plug from the socket in advance. 3. When disassemble the parts, remove the nylon band or wire holder as necessary. To assemble after repair, be sure to arrange the wires as they were.
MD-MS200W/MD-MS200/MD-MS200H REMOVING AND REINSTALLING THE MAIN PARTS (A2) x 3 Ø1.4 x 4.5mm Remove the mechanism according to the disassembling methods 1 to 4. (See Page 7.) How to remove the disc motor (See Fig. 8-1.) 1. Remove the solder joint (A1) x 1 of flex PWB. 2. Remove the screws (A2) x 3 pcs. and remove the disc motor. Take care so that the turnrable is not damaged. How to remove the slide motor (See Fig. 8-2.) 1. Remove the solder joint (B1) x 1 of slide motor lead wire. 2.
MD-MS200W/MD-MS200/MD-MS200H ADJUSTMENT Test disc MD adjustment needs two types of disc, namely recording disc (low reflection disc) and playback-only disc (high reflection disc). Type Parts No. Price Code UDSKM0001AFZZ AZ Test disc 1 High reflection disc ESYA 1014 (SONY) 2 Low reflection disc Recording minidisc Note: Use the low reflection disc on which music has been recorded. Entering the TEST mode 1.
MD-MS200W/MD-MS200/MD-MS200H Operation in each TEST mode 1. AUTO Mode Step No. • When the STOP button is pressed while the AUTO menu appears or during automatic adjustment, the mode changes to the TEST mode stop state. At this time the adjustment value is not output. • As for operation during continuous playback refer to [Explanation of TEST-PLAY mode]. • Adjustment NG: If the measurement value of adjustment FEO is out of range,focus ON failure occurs or adjustment error or TZC error occurs.
MD-MS200W/MD-MS200/MD-MS200H 3. RESULT Mode Step No.
MD-MS200W/MD-MS200/MD-MS200H •When the STOP button is pressed while the TEST-PLAY menu appears, or in TEST-PLAY or continuous playback mode, the mode changes to the TEST mode stop state. • When the PLAY button is pressed while the TEST-PLAY menu appears,continuous playback is initiated from the current pickup position. • Whenever the DISP button is pressed in the TEST-PLAY mode, the address changes as follows.
MD-MS200W/MD-MS200/MD-MS200H 5. TEST-REC Mode Step No. Display Setting Method Step 1 Test mode STOP state Step 2 BASS button Step 3 AUTO menu Step 4 SKIP UP button x 4times (Or SKIP DOWN button x 6 times) Step 5 TEST-REC menu Step 6 When the DISP button is pressed, the process proceeds to (7). When the PLAY button is pressed, the process proceeds to (9).
MD-MS200W/MD-MS200/MD-MS200H 7. NORMAL Mode Step No. Setting Method Step 1 Test mode STOP state Step 2 BASS button Step 3 AUTO menu Step 4 SKIP UP button x 6times (Or SKIP DOWN button x 4 times) Display [ [ Step No. T E S T ] A U T O ] Setting Method Step 5 NORMAL menu Step 6 PLAY button Step 7 TOC read Step 8 Hereafter operation in normal mode Display [ N O R M A L ] [Refer to the following description.
MD-MS200W/MD-MS200/MD-MS200H 9. Error data display Mode Step No. Step 1 Display Setting Method Test mode STOP state [ A U T O ] Contents Automatic adjustment Out of allowable range 13 Automatic adjustment adjustment Servo retry error (4 times) during ] 16 Automatic adjustment TZC error in TG, TB adjustment (TG, TB measurement value does not change.
MD-MS200W/MD-MS200/MD-MS200H Lead-in switch position adjusting method Note: Measure the position of lead-in switch in the INNER mode, and fix the position of lead-in switch at SUBQ FF85 to FF02. After retightening the screw, pressing the mechanism PWB in the arrow direction, measure again the position of lead-in switch. If the removed screw cannot be fit after position adjustment, fix with two screws. Lead In Switch Remove yhe screw when adjustment is made.
MD-MS200W/MD-MS200/MD-MS200H E2-PROM (IC402) writing procedure 1. Procedure to replace E2-PROM and write initial value of microcomputer in E2-PROM (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) Replace E2-PROM. Deprive E2-PROM of protection (connect the pins 8 and 2 of IC402). Refer to the latest E2-PROM data list. Press the Display/Lower-case Character button, Enter/Synchro button and Play/Pause button to start the test mode. Version display [Ver.
MD-MS200W/MD-MS200/MD-MS200H E2-PROM DATA LIST Focus setting Slide setting Item display F G _ _ Item display Set values 6C Set values H S L G _ 80 H 1C H F F 1 _ 70 H S L 2 _ F F 2 _ F0 H S L M _ 7F H F F 3 _ FEH S L V _ 20 H F F 4 _ 00 S K k _ 78 H F Z H _ ED S K t _ 50 H S K m _ 78 H H H F L n _ F6 H F L f _ 7F H Control setting F P n _ 00 H Item display F P f _ 88 H T BA _ A8H C 2 4 _ 1F H F L V _ 28 H C T 1 _ 13 H C 2 5 _ 23 H W T f _
– 19 – SKIP UP T SKIP UP T SKIP UP SKIP DOWN SKIP DOWN SKIP DOWN DATA SKIP DOWN EEPROM SKIP UP E SKIP UP DinMon SKIP UP NORMAL NER SKIP DOWN REC SKIP DOWN PLAY SKIP DOWN SKIP UP • When the STOP key is pressed in the specific mode, the mode changes to the TEST mode stop state.
– 20 – TEO: Lf SKIP UP Gb SKIP UP Gg SKIP UP Gl SKIP UP H f L f SKIP UP Hb Lb SKIP UP Hg Lg SKIP UP h f l f SKIP UP LON: SKIP UP FEO: SKIP UP SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN P-MODE PLAY P-MODE PLAY BASS SQ Pit section continuous playback RPW: Record power laser ON AP : measurement value : Adjustment value : Addres Groove section continuous playback BASS 2 sec.
– 21 – A D 0 8 A 0 DISP A D 0 7 0 0 DISP A D 0 3 C 0 DISP PLAY PLAY PLAY PLAY PLAY SQ AP : Address Continuous playback Start address indication 4 Start address indication 3 Start address indication 2 Start address indication 1 Continuous record menu DISP R E C A D 0 8 A 0 DISP A D 0 7 0 0 DISP A D 0 3 C 0 DISP A D 0 0 5 0 T PLAY PLAY PLAY PLAY PLAY Continuous Record Change Chart AP : Address Continuous record • When the STOP key is pressed in the specified mode, the mode
– 22 – E9 SKIP UP E8 SKIP UP E7 SKIP UP E6 SKIP UP E5 SKIP UP E4 SKIP UP E3 SKIP UP E2 SKIP UP E1 SKIP UP E0 E PLAY SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN After 2 seconds DISP SKIP DOWN DATA CLEAR : Error Code • When the STOP key is pressed in the specified mode, the mode changes to the TEST mode stop state.
SLG SL 2 SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN – 23 – SKIP DOWN SKIP DOWN Control setting menu C 0 0 SKIP UP C 4 9 SKIP UP C 0 1 SKIP UP PLAY CTRL SKIP DOWN SKIP DOWN C02 SKIP DOWN ~C48 EEPROM Control Setting Change Chart TM PLAY TEMP : Temperature code : Normal setting value • When the STOP key is pressed in the specified mode, the mode changes to the TEST mode stop state.
– 24 – FSS SKIP UP WT f SKIP UP FLV SKIP UP FP f SKIP UP FPn SKIP UP FL f SKIP UP FL n SKIP UP FZH SKIP UP FF4 SKIP UP FF3 SKIP UP FF2 SKIP UP FF1 SKIP UP FG PLAY SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN F o c u s : measurement value SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN SKIP DOWN : measurement value • When the STOP key is pressed in the specified m
MD-MS200W/MD-MS200/MD-MS200H EXPLANATION OF ERROR DISPLAY Errors Corrective action Can't REC Error display • Defect occurred 10 times successively during REC-PLAY. • During REC-PLAY, the break that full, high temperature memory taped occurred. • When reads it, and impossibility tries it again, and an address doesn't hire you in REC state repeatedly for 20 seconds either. • Check that disc is free from flaws, dust, fingerprint, black spots, etc. Check for significant disalignment and runout of disc.
MD-MS200W/MD-MS200/MD-MS200H NOTES ON SCHEMATIC DIAGRAM (CH), (TH), (RH), (UJ): Temperature compensation (ML): Mylar type • The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given. • Parts marked with “ ”( ) are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
– 27 – M A B E F Figure 27 BLOCK DIAGRAM 21 16 21 10 12 25 27 IC202 D-RAM MOTOR DRIVER IC601 BH6512FS 45 19 65 64 36 39 11 9 26 18 20 3 4 14 15 20 28 29 ~ 4 ~9 51 ~ 58 59 3 70 76 23 ~ 25 21 9 30 32 34 38 41 53 54 56 ENDEC IC201 LR37646 21 10 ~ 22 21 ~ 23 79 SW402 HOLD SW SW904 DISC IN SW901 READ IN SW903 DISC PROGRAM SW902 DISC MEDIA SW401 EJECT 86 89 66 ~ 100 MOTOR DRIVE IC851 RF SIGNAL PROCESSOR IC101 IR3R50 60 Q351~Q354 HEAD DRIVER IC351 10 11 14 71 72 1 Q102 Q1
MD-MS200W/MD-MS200/MD-MS200H P28 P29 P30 A PLAYBACK SIGNAL RECORD SIGNAL RFI2 RFEQ RFO1 EFMAI RFO2 GND2 RFO3 56 RFBP2 51 ADI2 50 IC101 IR3R50 C122 1 C121 ADI1 46 1 ADO1 45 C119 C120 0.0033 330P HPFO 44 CK104 LPFI 43 12 FOUT 119 20 35 36 LPFO 42 WBO 41 D R140 47K C118 CK103 330P CK102 RFENV 40 R139 47K TEOUT TENF FENF FEOUT TOTAL VCC1 TONF GND1 DFCTO DFCTI TCGAV DISC LDVAR LDON TCRSP 39 TCRSO 38 C164 0.047 R145 3.3M R132 39K R160 100K R131 100K C114 10/6.
MD-MS200W/MD-MS200/MD-MS200H P28 P29 P30 C118 CK103 330P 40 CK102 R139 47K TP201 RAD2 RAD3 RAA9 RARASX RAWEX RAD1 RAD0 TP205 1 2 3 4 5 I/O1 I/O2 WE RAS A9 GND I/O4 I/O3 CAS OE 20 19 18 17 16 RAD3 RAD2 RACASX RAOEX 15 14 13 12 11 C354 15 16 17 18 19 20 21 22 23 24 25 26 27 RAA8 RAA7 RAA6 RAA5 RAA4 C507 10/6.3 A0 A1 A2 A3 10 VCC 9 8 7 6 5 4 3 2 R500 4.7 C511 1 C202 106.3 A8 A7 A6 A5 A4 6 7 8 9 L202 0.47µH TP202 CK105 VCC C357 0.
MD-MS200W/MD-MS200/MD-MS200H P28 P29 P30 R361 8.2 BUTTON FLEXIBLE PWB C-MODE REC EDIT DISPLY PLAY P-MODE SKIP UP BASS VOL UP ENTER STOP SKIP DOWN VOL DOWN R458 56K TP401 TP403 REC PLAY C734 0.1 19 24 IC701 IR3R54N 17 5 RI 19 20 L861 47 R852 3 1 C867 220/4 2 D861 SB10015C OUT C846 1 R847 390K C861 1 2 3 GND C812 0.18 C809 10/6.3 3 4 2 TP807 R829 470K R810 200K Q804 2SA1745 C811 0.33 R812 10K R813 C810 0.33 IC802 TC7S00FU R811 180K C827 220/4 L822 4.7µH 2.
MD-MS200W/MD-MS200/MD-MS200H PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 IC101 VOLTAGE PIN NO. VOLTAGE 0.7V 37 1.3V 0.7V 38 0V 1.37V 39 1.48V 1.37V 40 1.25V 1.12V 41 0.7V 1.37V 42 1.35V 1.37V 43 1.37V 1.37V 44 1.3V 1.37V 45 1.36V 1.37V 46 1.37V 1.37V 47 1.34V 1.37V 48 0.03V 1.37V 49 1.18V 1.37V 50 1.16V 1.37V 51 0.67V 1.37V 52 0.67V 1.37V 53 1.35V 1.37V 54 1.36V 1.34V 55 1.67V 2.36V 56 1.16V 0V 57 1.37V 0.02V 58 1.37V 0V 59 0V 0.08V 60 1.18V 1.
MD-MS200W/MD-MS200/MD-MS200H A B 6 7 R222 C212 C211 55 76 C207 R415 R414 R413 IC802 70 65 50 80 45 85 30 IC405 10 C401 L841 R401 R140 R139 C725 C123 R144 C103 R101 C105 C127 C120 C119 R138 R137 R134 55 50 54 C121 C128 C101 60 45 C126 R132 C130 65 37 R136 C129 IC101 40 C160 C131 70 1 C124 C122 C133 C150 C727 R762 R761 R754 Q721 R725 R701 R703 C701 F C703 R726 12 R143 C132 P34 3 D 1 R424 10 C756 5 C757 IC703 36 72 5 C125 C16
MD-MS200W/MD-MS200/MD-MS200H P34 2 - D TO FLEXIBLE PWB (227) P35 12 - D P34 2 - G TO FLEXIBLE TO LCD FLEXIBLE PWB (7) PWB (227) BATTERY( ) C471 R471 C715 C824 R824 C828 C751 Q711 TP704 R727 C731 R711 R712 13 12 15 10 20 10 14 IC701 5 TP712 C509 C500 C733 TP711 24 TP713 1 C721 5 R719 TP714 CK515 C702 R720 TP710 R702 R717 IC501 1 C501 L500 15 25 TP500 C161 TP705 TP210 R500 20 C502 C711 C712 28 R502 TP709 C713 TP131 C510 L491 C752 TP708 TP703 R715 C507 TP
MD-MS200W/MD-MS200/MD-MS200H A LCD UNIT(220) B COLOR BR RD(R) TABLE BROWN RED OR YL GR ORANGE YELLOW GREEN BL VL GY WH(W) BK PK BLUE VIOLET GRAY WHITE BLACK PINK PICK UP UNIT(3) C TO MAIN PWB CNS101 P33 7 - F P33 10 - B TO MAIN PWB CNS201 D HEAD DRIVE FLEXIBLE PWB(227) E C354 P33 10 - B TO MAIN PWB C353 F + 14 C357 CNS402 8 CN351 Q351 Q353 IC351 Q354 HEAD JOINT FLEXIBLE PWB(6) 7 Q352 1 D351 C351 G D352 R361 C361 HEAD DRIVE PWB-B1(TOP VIEW) HEAD DRIVE PWB-B1
MD-MS200W/MD-MS200/MD-MS200H REC CHARACTER /TIME EDIT/ AUTO MARK/ TIME MARK TO MAIN PWB DISPLAY CNS401 OFF P33 7 - D FLEXIBLE PWB UNIT (202) MODE/INS REC LEVEL BASS/DEL VOLUME NAME ENTER/F.
MD-MS200W/MD-MS200/MD-MS200H WAVEFORMS OF CD CIRCUIT PLAY Condition CH1=500mV DC P *10 1 CH1=2V DC 10:1 CH2=2V DC 10:1 CH3=2V DC 10:1 CH4=2V DC 10:1 1s/div (1s/div) ENV 500s/d TP145 (EFM) 4 TP143 (FEOUT) 7 TP144 (TEOUT) 11 TP605 (SPDRR) 12 TP604 (VS) 1.8V P-P CH4 Position -2.71 div CH Position To CH3=2V DC 10:1 CH4=2V DC 10:1 50ms/div (50ms/div) ENV PLAY Codition (MO DISC) CH1=2V DC P *10 2 CH2=500mV DC P *10 20µs/d CK104 (HPFO) 11 TP605 (SPDRR) 12 TP604 (VS) CH3 Position -2.
MD-MS200W/MD-MS200/MD-MS200H TROUBLESHOOTING It is advisable to use the TEST mode (refer to Error Data Display Mode, P15) indicating the causes of troubles before starting repair. Causes of operation errors (up to 10 errors) are recorded as error codes. This information is useful for repair. When does not function When the CD section does not operate When the objective lens of the optical pickup is dirty,this section may not operate.Clean the objective lens,and check the playback operation.
MD-MS200W/MD-MS200/MD-MS200H • Abnormal display Is waveform output from CNS 402 pins 1 to 3? Are the pin7 (VCC) and pin 6 (GND) normal? Is waveform output from IC 401 pins 13 to 15? No Yes Check between IC401 and CNS402. No Check the periphery of IC401. Yes Check for pattern breakage of flexible PWB, check for defects of display microcomputer (replace the display unit).
MD-MS200W/MD-MS200/MD-MS200H • Test mode check Insert a high reflection (low reflection) disc, and once perform automatic adjustment in AUTO mode, and then check in MANUAL mode. Simultaneously observe waveforms of EFM(TP145), FEOUT(TP143), and TEOUT(TP144).
MD-MS200W/MD-MS200/MD-MS200H Continued from the preceding page In case of high reflection disc, proceed to the item "normal playback".In case of low reflection disc, check whether adjustment is within allowable range in the TOTAL level adjustment step. No Check whether values of pins 10, 11, 14, and 15 of IC201 and pins 30 and 32 of IC101 (TP143) change when the / button is pressed.
MD-MS200W/MD-MS200/MD-MS200H • Normal playback When the address up to the sector address has been proved to be normal in the test mode. Is initialization performed normally in case of high reflection disc normal playback? Does the playback time display act? Yes No Check IC201 and IC202 connection line.
MD-MS200W/MD-MS200/MD-MS200H • Recording/playback operation Insert a low reflection disc, and ascertain audio output by normal playback, and then set TEST REC mode. Does the head move down, failing to start record even when the continuous record mode is set after address? Yes Check voltage of pins 56 and 57 of IC401, pins 2, 4, 7, and 9 of IC851, pins 12 and 13 of CNS601. Check whether disc is record-inhibited.
MD-MS200W/MD-MS200/MD-MS200H FUNCTION TABLE OF IC IC401 RH-iX2596AF02(IX2596AF):System Microcomputer (1/2) Pin No.
MD-MS200W/MD-MS200/MD-MS200H IC401 RH-iX2596AF02(IX2596AF):System Microcomputer (2/2) Pin No.
MD-MS200W/MD-MS200/MD-MS200H IC406 VHiRTC4543B-1 (RTC4543B):Rialtime Clock Pin No. Terminal Name Function Input/Output 1*-4* NC — Be sure to use this terminal in OPEN state so as to get more stable connected inside, and is the low truth line drawing oscillation. 5 FOE Input When this terminal is on H level, frequency selected by the FSEL terminal is output from the FOUT terminal. When this terminal is on L level, the FOUT terminal is set to highimpedance.
MD-MS200W/MD-MS200/MD-MS200H —MEMO— – 46 –
MD-MS200W/MD-MS200/MD-MS200H PARTS GUIDE MODEL MD-MS200W MD-MS200 MD-MS200H “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. No. 3. PART NO. 4. DESCRIPTION For U.S.A. only Contact your nearest SHARP Parts Distributor to order.
MD-MS200W/MD-MS200/MD-MS200H NO. PRICE RANK PART CODE DESCRIPTION INTEGRATED CIRCUITS IC101 IC201 IC202 IC351 IC401 VHIIR3R50//-1 VHILR37646/-1 RH-IX2567AFZZ VHI74ACT02F-1 RH-IX2596AF02 J J J J J AV BF BA AF AX RF Signal Processor,IR3R50 ENDEC,LR37646 4bit D-RAM,IX2567AF Head Driver,74ACT02F System Microcomputer, IX2596AF E2 -PROM,S29294A Inverter,TC7W14FU NAND Gate,7SH00FU Reset,61AC2102 Realtime Clock,RTC4543B AD/DA Converter,AK4520VF Motor Driver,BH6512FS Audio Amp.
MD-MS200W/MD-MS200/MD-MS200H NO.
MD-MS200W/MD-MS200/MD-MS200H NO.
MD-MS200W/MD-MS200/MD-MS200H NO. PRICE RANK PART CODE 248 TLABM0562AFZZ J 249 TLABS0472AFZZ J 250 601 603 604 605 606 TLABM0563AFZZ LX-BZ0903AFFN LX-BZ0856AFFD LX-BZ0805AFFN LX-BZ0908AFFN LX-BZ0910AFFN J J J J J J DESCRIPTION NO. AD Label,Specifications [MD-MS200W for Taiwan Only] AC Label,Laser Caution [MD-MS200W/H] Label,Feature [MD-MS200H] AA Screw,ø1.4×3.0mm AC Screw,ø1.8×7.7mm AB Screw,ø1.7×2.5mm AA Screw,ø1.4×2.0mm AC Screw,ø1.7×2.
MD-MS200W/MD-MS200/MD-MS200H 107 PWB-B2 21 A 115 6 11 23 B 119 a 20 13 22 30 3 C 33 16 7 4 D 31 109x2 17 105 15 118 34 19 112 32 14 105 116x2 18 5 24 E M903 106 1 a' 2 F 117 106 M1 109 105 114 110 G 105 8 PWB-B1 114 105 114 M902 108 H 9 108 111 111 1 2 3 4 Figure 5 MD MECHANISM EXPLODED VIEW –5– 5 6
MD-MS200W/MD-MS200/MD-MS200H 216 250 A 237 240 605x2 243 212 B 214 236 605x2 249 219 215 231 247 C 230 213 241 211 244 Mechanism 217 227 D 242 601x2 220 233 245 201 202 208 E 210 209 204x4 246 234 235 203 603x4 225 F 205 239 229 203 226 606 PWB-A 604x3 206 207 224 605x2 G 605 221-2 221 221-1 605x2 H 1 2 3 4 Figure 6 CABINET EXPLODED VIEW –6– 5 6
MD-MS200W/MD-MS200/MD-MS200H PACKING METHOD (MD-MS200H FOR UK ONLY) 1. Case 2. Packing Case 3. Packing Add. 4. Carrying Bag 5. Warranty Card 6. Service Card 7. Operation Manual,Illust 8. Operation Manual 9. Case, AC Adaptor 10. Pad, AC Adaptor 11. Pecording Mini Disc 12. Rechageble, Battery 13. Connecting Cord, RCA Type 14. Stereo Headphones Unit 15. Remote Control 16. AC Adaptor 17.
MD-MS200W/MD-MS200/MD-MS200H PACKING OF THE SET (MD-MS200 ONLY) SETTING POSITION OF SWITCHES AND KNOBS UNIT Disc Cover HOLD CLOSE OFF Remote Control HOLD Volume CANCEL CENTER Remote Control Rechargeable Battery AC Adaptor Recording Mini Disc SPAKZ0424AFZZ Pad,AC Adaptor Connecting Cord, RCA Type Stereo Headphones Unit Operation Manual Quick Guide, Spanish Caution Headphones SPAKF0110AFZZ Case,AC Adaptor SSAKH0289AFZZ Polyetylene Bag,Unit i in M isc D P R A H S Carrying Bag SPAKA2624AFZZ Pac
MD-MS200W/MD-MS200/MD-MS200H Writer and Editor: Quality & Reliability Control Center of Communication & Audio Systems Group, Sharp Corp.
