Service manual

ManualsBrandsSharp ManualsGarage Door OpenerMD-M3

– 21 –

MD-M3/M1

5. TEST-PLAY mode

Step 1 Test mode STOP state The AUTO preliminary adjustment should have been completed. [ t s m 1 3 e ]

Step 2 Press the NORMAL button. TEST-PLAY menu [ T E S T _ P L A Y _ ]

Step 3 Press once the DISPLAY button. ADDRESS setting (Target address initial value is indicated) [ A D R E S _ 0 0 5 0 ]

Press once the PLAY button.

Step 4 Continuous playback (pit section) (Address + C1 error indication) [s c ]

Continuous playback (groove section)

(Address + C1 error indication) [a c ]

Step 5 Press once the DISPLAY button. (Address + ADIP error indication) [a a ]

Continuous playback (groove section)

Step 6

Press once the STOP button

. TEST-PLAY menu [ T E S T _ P L A Y _ ]

Step No.

Setting Method

6. TEST-REC mode

Step 1 Test mode STOP state The AUTO preliminary adjustment should have been completed. [ t s m 1 3 e ]

Step 2 Press twice the NORMAL button. TEST-REC menu [ T E S T _ R E C _ _ ]

Step 3 Press once the DISPLAY button. ADDRESS setting (indication of address initial value) [ a 0 0 3 2 _ p w ]

Step 4

Press once the PLAY button.

While searching, set the search output to "H". To start continuous play,

[ a p w ]

return it to "L".

Continuous recording

Step 5

Press once the STOP button.

TEST-REC menu [ T E S T _ R E C _ _ ]

Step No.

Setting Method

Remarks Display *

Remarks

Display *

(For confirmation of the playback ability at the named address.)

With recording mini disk (For confirmation of the playback ability at the named address.)

7. INNER mode

Step 1 Test mode STOP state [ t s m 1 3 e ]

Step 2 Press the CD button. INNER menu [ _ _ I N N E R _ _ ]

Step 3

Press once the PLAY button.

INNER switch position measurement [s c ]

(SUBQ address and C1 error are also indicated.)

Step 4

Press once the STOP button.

INNER menu [ _ _ I N N E R _ _ ]

Step No.

Setting Method

Remarks Display *

• : Address

4. EEPROM setting mode

Shown in page 23,24.

* Actual indicator character is shown on page 19 . ( See Table 19 )

• If the STOP button is pressed while the TEST-PLAY menu is displayed, TEST mode STOP state is set.

• If the PLAY button is pressed while the TEST-REC menu is displayed, continuous record is started from the current pickup position.

• Whenever the NORMAL button is pressed in the address setting mode, the address changes as follows.

0 0 5 0 → 0 3 C 0 → 0 7 0 0 → 0 8 A 0 → 0 0 5 0 → …………

• Whenever the DISPLAY button is pressed in the address setting mode, the digit which is changed with / changes

as follows.

0 0 5 0 → 0 0 5 0 → 0 0 5 0 → 0 0 50 → …………

• The digit of address which has been specified with / button in the address setting mode is set to +01H/-01H.(0~F)

* If the / button is held down, the setting changes continuously with 100 ms cycle.

• Be sure to remove since excessive raising results in breakage of the pickup.

▲

* Actual indicator character is shown on page 19 . ( See Table 19 )

• If the STOP button is pressed while the TEST-PLAY menu is displayed, TEST mode STOP state is set.

• If the PLAY button is pressed while the TEST-PLAY menu is displayed, continuous playback is started from the current pickup position.

• Whenever the NORMAL button is pressed in the address setting mode, the address changes as follows.

0 0 5 0 → 0 3 C 0 → 0 7 0 0 → 0 8 A 0 → 0 0 5 0 → …………

• Whenever the DISPLAY button is pressed in the address setting mode, the digit which is changed with / changes

as follows.

0 0 5 0 → 0 0 5 0 → 0 0 5 0 → 0 0 5 0 → …………

• The digit of address which has been specified with / button in the address setting mode is set to +01H/-01H.(0~F)

* If the / button is held down, the setting changes continuously with 100 ms cycle.

▲