LCD MONITOR LCD FARBMONITOR MONITEUR LCD MONITOR LCD MONITOR LCD LL-T1610W OPERATION MANUAL BEDIENUNGSHANDBUCH MANUEL D'UTILISATION MANUALE D’USO MANUAL DE FUNCIONAMIENTO
Notice for Users in the USA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TCO'99 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notice for Users in Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notice for Users in the UK . . . . . . . . . . . . . . . . . .
Notice for Users in the USA FCC Statement WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
English Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire.
This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/ EEG. Dette udstyr overholder kravene i direktiv nr.
Notice for Users in the UK FOR CUSTOMERS IN U.K. IMPORTANT The wires in this mains lead are coloured in accordance with the following code : GREEN-AND-YELLOW : Earth BLUE : Neutral BROWN : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows.
• • • • • • • • Monitor and accessory checklist • Please check that the following items are included in the package. – LCD monitor (1) – AC adapter (1) – Power cord (1) – Utility Disk (For Windows/Macintosh) (1) – USB cable (1) – Operation manual (1) Under certain display conditions, minute specks or spots may be noticeable. This is common for liquid crystal monitors and is not a malfunction. The LCD panel has been manufactured using highly elaborate technology. Properly working pixels comprise 99.
Product description Front view Rear view e w q 7 8 9 1 2 3 4 5 6 0 1. INPUT button Use this button to switch between input signals. (analog ↔ digital) 2. MENU button This button is used to pop-up, select and close the On Screen Display (OSD) Menu. 3. SELECT button Selects the menu option to be adjusted. 4. buttons These buttons are used to adjust backlight brightness. When the OSD Menu is displayed these buttons are used to increase or decrease the value of a selected option. 5.
English Connecting the monitor and turning the monitor on and off 4. Connect the AC adapter to the monitor’s power terminal, and connect the power cord to the AC adapter. Connecting the monitor to a power source Use only the AC adapter and power cord supplied. Run cord through hole Notes: • Do not overly bend the cable or add extension cords as this could lead to malfunction. • Do not remove the label next to the power-input terminal. Also do not touch the switch covered by the label. 1.
Connecting the monitor and turning the monitor on and off 8. Replace the rear cover. If connecting to a D-sub 15 pin 2 row Apple Power Macintosh, attach a Macintosh conversion adapter (to be purchased separately) to the analog signal cable. q Macintosh conversion adapter w Analog signal cable After connecting the adapter, tighten the screws on each side to fix into place 9. Place power plug into AC outlet.
3. Replace the stand cover. Switching between input signals To obtain the desired signal use the INPUT button to switch over to it. Within a matter of seconds the signal type will be displayed on the upper right-hand part of the screen.
Connecting the monitor and turning the monitor on and off If the "Add New Hardware Wizard" has not appeared: For Windows95 1. Place the Utility Disk in the computer's A drive. Installing monitor set-up information into Windows95. This explanation assumes that the floppy disk drive is "A drive". 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 1. Place the Utility Disk (provided) into the computer's A drive. 4. Click on [Settings], [Advanced] and [Monitor]. 3.
Installing the ICC profile Installing the monitor’s ICC profile. (If the set-up information has already been installed, so too has the profile, and there is no need to install it.) This explanation assumes that the floppy disk drive is "A drive". For WindowsMe Installing monitor set-up information into WindowsMe, and setting the monitor's ICC profile as a predetermined value. This explanation assumes that the floppy disk drive is "A drive". If the "Add new Hardware Wizard" has appeared: 1.
Connecting the monitor and turning the monitor on and off Information about the ColorSync profile (MacOS) Connecting a USB device About the ColorSync profile ColorSync is the Apple Corporation's color management system and is a function that enables color resolution to be realized when used with a compatible application. A ColorSync profile describes the color characteristics of the LCD monitor. Notes: • This monitor's ColorSync profile works with MacOS8.5 or above.
4. Plug the USB device into the monitor's USB downstream port. USB downstream port USB device Run through hole 5. Replace stand cover. Run signal cable and USB cable through here 2 1 6. Replace rear cover. To replace it follow step 8 of Connecting the monitor to a power source on page 12.
Before adjusting the screen display About screen adjustment The method of adjustment differs depending on whether the analog signal or the digital signal is being used. For analog signal 1. First perform an automatic adjustment. (p. 19) 2. Perform manual adjustment where necessary. (p. 20) Adjustment lock function By disabling the control buttons (i.e. setting the lock) any attempted changes to adjusted values will be avoided. 1. Press the power button to turn off the monitor power. 2.
Opening the Adjustment Pattern (for Windows) If you are using Windows, you can use the Adjustment Pattern (for Windows) on the accompanying Utility Disk. This explanation is for Windows 95/98/Me/2000, and assumes that the floppy disk drive is "A drive". Automatic screen adjustment Options in the ADJUSTMENT Menu can be adjusted automatically (CLOCK, PHASE, H-POS V-POS).
Adjusting the screen display (when using an analog signal) CLOCK The figure below demonstrates how to adjust so that vertical flicker noise is not emitted. ( buttons) Manual screen adjustment Adjustments can be made using On Screen Display (OSD) Menu provided. 1. Display an image that makes the entire screen very bright. If using Windows, you can open and use the Adjustment Pattern on the accompanying Utility Disk. (p. 19) 2. Press the MENU button. The ADJUSTMENT Menu will be displayed.
GAIN CONTROL Menu WHITE BALANCE Menu MANUAL: Individual menu options are manually adjusted. AUTO: Every menu option is automatically adjusted using the Auto Gain Control* function, Notes: • Press the button to select [AUTO]. • To choose a menu option: SELECT button • To go to the next menu: MENU button Notes: • On settings other than [STD] not all graduations can be displayed. To display all graduations, set to [STD]. buttons to select [COOL], [·], [STD], [·], • Use the [WARM] or [USER].
Adjusting the screen display (when using an analog signal) MODE SELECT Menu SCALING (Level of scaling) If [EXPAND] is set on [ON1] or [ON2], the sharpness of the image can be adjusted. ( buttons) Note: • If [EXPAND] is set on [OFF], [SCALING] cannot be adjusted. COLOR MODE If this is set on [OFF], the original color scheme of the LCD monitor will be displayed. If this is set on [ON], the colors of will be corrected according to the computer image.
WHITE BALANCE Menu Manual screen adjustment Adjustments can be made using the On Screen Display (OSD) Menu provided. 1. Display an image that makes the entire screen very bright. If using Windows, you can open and use the Adjustment Pattern on the accompanying Utility Disk. (p. 19) 2. Press the MENU button. The WHITE BALANCE Menu will be displayed. Notes: • On settings other than [STD] not all graduations can be displayed. To display all graduations, set to [STD].
Adjusting the screen display (when using a digital signal) MODE SELECT Menu Notes: • Depending on the resolution of the input signal, even if menu options can be selected, the display may not change. • To choose a menu option: SELECT button • When adjustment complete: MENU button OSD H-POSITION (OSD horizontal position) The position of the OSD display can be moved to the left and right. ( buttons) OSD V-POSITION (OSD vertical position) The position of the OSD display can be moved up and down.
Adjusting the backlight Adjusting the angle of the monitor Carry out the commands without the On Screen Display (OSD) Menu displayed. If the OSD Menu is displayed, press the MENU button (several times may be required) and begin when the OSD Menu has disappeared. 1. Without the OSD Menu being displayed, push the or the button. The [BRIGHT] bar will be displayed on the screen. Lightly holding both sides of the monitor, adjust it to a suitable viewing angle.
Monitor care and repair Monitor care Troubleshooting Always remove the plug from the AC outlet when cleaning the monitor. If you think the monitor may be faulty, please check the following points before taking it to be repaired. If afterwards it still does not work, please contact the shop where you purchased the monitor or your nearest Sharp authorized Service Center. Cabinet and control panel section Use a soft dry cloth to lightly wipe away any grime from the cabinet and control panel.
Product specifications English Specifications Dimensions (Units: mm) 390 310 377 LCD display 40 cm measured diagonally Anti Glare Low Reflection TFT LCD module Resolution (max.) SXGA 1280 X 1024 Displayable colors (max.) Approximately 16.77 million colors (8 bit) Brightness (max.) 230cd/m² Dot pitch 0.248(H) 0.248(V) mm Contrast ratio 300:1 Angle of visibility Left-right 160°; Up-down 130° Screen display size Horizontal 317.8 mm X Vertical 254.2 mm Video signal Analog: Analog RGB (0.
Specifications Relevant signal timings (analog) Display mode VESA 640x480 640x400 720x400 800x600 1024x768 1152x864 1280x960 1280x1024 US text Power Macintosh series Sun Ultra series 720x400 640x480 832x624 1024x768 1152x870 1024x768 1152x900 1280x1024 • • • • Relevant signal timings (digital) Hsync (kHz) Vsync (Hz) Dot frequency (MHz) 31.5kHz 37.9kHz 37.5kHz 43.3kHz 37.9kHz 37.9kHz 35.1kHz 37.9kHz 48.1kHz 46.9kHz 53.7kHz 48.4kHz 56.5kHz 60.0kHz 68.7kHz 67.5kHz 60.0kHz 64.0kHz 80.0kHz 31.
The digital signal input connector pin 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 DDC (Plug & Play) 8 This monitor supports the VESA DDC (Display Data Channel) standard. DDC is a signal standard for carrying out Plug & Play functions on the monitor or PC. It transfers information such as degree of resolution between the monitor and PC. You can use this function if your PC is DDC compliant and if it is set so that it can detect the Plug & Play monitor.
Instructions for installing a VESA compliant arm An arm based on the VESA standard can be attached to the monitor. The arm must be purchased separately. 5. Remove the four screws and then remove the stand from the monitor. When choosing the arm to be installed please take note of the following points. • The arm should be compatible with the VESA standard, and there must be a gap of 75mm x 75mm between the screw holes on the section to be attached.
SHARP CORPORATION © 2001 SHARP CORPORATION 01F DSC2 TINSE1021MPZZ(2)
