Manual

Direct Button Operation
POWER
OPTION SLEEP SAVINGFREEZE
EZD
CO AVMODEVIEWMODEFLASHBACK
AQUOS
NET APPS
Mutes the current sound output.
Press MUTE.
• ,,(_),, will be displayed on the screen for 30 minutes, and
the sound is silenced.
• Within 30 minutes of pressing MUTE, mute can be
canceled by pressing VOL+/- or MUTE.
• Mute will be canceled after 30 minutes have passed.
However, the TV will not suddenly output a loud sound as
the volume level is set to 0 automatically.
You can change channels in several ways.
Method 1
Using CHA/V on the remote control unit or on the TV.
Method 2
Using remote control buttons 0-9, • (DOT).
Examples:
To select a 1 or 2-digit channel number (e. g., Channel 5}:
Press 5 _ ENT.
To select a 3-digit channel number (e. g., Channel 115):
Press 1 _ 1 _ 5_ ENT.
To select a 4-digit channel number (e. g., Channel 22.1):
Press 2 --_ 2 ---> • (DOT) --_ 1 --->ENT.
Method 3
Selecting the program from Channel list.
1 Press iNPUT on the remote control unit.
• The INPUT list displays.
2 Press 4/I,- to select "AIR" or "CABLE".
• The Channel list displays.
3 Press A/_' to select the desired channel, and then
press ENTER.
Allows you to set a time when the TV automatically
switches to standby.
Press SLEEP.
• The remainingtime displayswhen the sleep timer has been set.
• Each time you press SLEEP, the remaining time switches
as shown below.
Off ,_, 30 _ 60 ,_,90 ,m 120
t !
• When set, the time automatically starts counting down.
• If you want to adjust the sleep timer, you can press SLEEP
twice then change the time setting.
• When it is 5 minutes before the time expires, the remaining
time will start to keep appearing every minute.
• Select "Off" by pressing SLEEP to cancel the sleep timer.
• The TV willenter standbywhen the remainingtime reaches 0.
Press FLASHBACK to switch to the previouslytuned
channel.
• PressFLASHBACK againto switch backtothe currently
tuned channel.
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection will be made if
there is no operation within a few seconds.
• If you push "0" by itself, nothing will happen.
• Complete the above steps within a few seconds.
When you enter 0-9 and • (DOT), channel selection will be
made if there is no operation within a few seconds.
• FLASHBACK will not work if no channel has been
changed after the TV is turned on.
Allows you to capture and freeze a moving image that
you are watching.
Press FREEZE.
• A moving imageis captured.
PressFREEZE againto cancelthe function.
You can change the volume by pressing VOL+/- on
the TV or on the remote control unit.
• To increase the volume, press VOL 4-.
• To decrease the volume, press VOL-.
Audio status
• When this function is not available, "No displaying still
image available." will display.
• The still image automatically goes out after 30 minutes.
• If you are using the freeze function and a broadcast
activates the V-CHIP BLOCK, the freeze function will be
canceled and a V-CHIP BLOCK message will appear.
• You can have the same settings by choosing "Freeze" on
the menu items. (See page 30.)
Speaker Variable sound Mute
• When "Output Select" is set to "Variable", the indicator on
the screen changes as shown below.
• See page 31 for details on the Output Select function.
(D- 20
[)_ 'rtlo_ded _:_om www.ManualslJb.com mare als se{rch engine