Manual

On-Screen DispJay Menu
You can run EZ Setup again, even after setting up tile
preset channels.
Language: Select from among 3 languages (English,
French and Spanish).
TV Location: Select "Home" or "Store" for the location
where you plan to install the TV. This product qualifies
for ENERGY STAR in Home mode defauR setting.
Home: "Power Saving" is set to "Off", and AV MODE is set to
"STANDARD".
Store: "Power Saving" is set to "Oft" and AV MODE is set to
"DYNAMIC (Fixed)". Picture Reset and Feature Demo can
be set.
Picture Reset: AV MODE will be set to "DYNAMIC (Eixed)"
regardless of whether Picture Reset is "On" or "Off". If
you select "On", AV MODE will be reset to "DYNAMIC
(Fixed)" if there is no operation for 30 minutes. When "Oft"
is selected, AV MODE will be set to "DYNAMIC (Fixed)".
Feature Demo: When "On" is selected, after all the settings
are completed, the Feature Denlo screen is displayed if
there is no operation for several minutes.
= ENERGY STAR qualification is based on AV MODE
"STANDARD".
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
OH Search: Channel auto search makes the TV look for
all channels viewabb in the set area.
o See initial installation on page 12 for setting each item.
o if no channel is found, confirm the type of connection made
with your TV and try "EZ Setup" again.
If Initial Installation does not memorize all the channels
in your region, follow the instructions below to manually
memorize the channels.
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
OFt Search: Channel auto search makes the TV look for
all channels viewabb in the set area.
OFt Memory: You can select the channels to skip in each
ANALOG (Air), ANALOG (Cable), DIGITAL (Air) and
DIGITAL (Cable).
On: Skips channels.(Channelselectiondisabledusing CH
A/V.)
Off: Does not skip channels.(Channelselectionenabled using
CHA/V.)
Antenna Setup Digital: In order to receive digital air
broadcasts, you need a digital broadcast antenna.
You can confirm the antenna configuration through the
"Antenna Setup Digital" screen. If necessary, adjust the
direction of the antenna to obtain the maximum signal
strength.
Signal Strength: The signalstrength of DIGITALchannelis
displayed.The signalinformationis based on the current
channel.
Channel Strength: Inputthe 2 digit channelnumberto check
the signal strength of the selectedchannel Makesure the
signal is strong enoughfor each channel.
* Thisfunction isavailablefor DIGITAL(Air)only.
o See Initial installation on page 12 for setting each item.
o if no channel is found, confirm the type of connection made
with your TV and try channel search again.
This setting allows you to skip the HDMI or PC-IN Input
("INPUT4 (PC)", "INPUT5 (HDMI)", "INPUT6 (HDMI)"
and "INPUT7 (HDMI)") on the Input Selection operation.
Yes: Skips the input.
No: Does not skip input.
Lets you set the input temlinal displayed when using
the INPUT SOURCE menu or channel display. Press
A/V/-_/I_ to select the new name for the input
mode.
o You cannot change labeb if the INPUT SOURCE is TV.
For adjusting a picture's horizontal and vertical
position.
H-Poe.: Centers the image by moving it to the btt or
right.
V-Pos.: Centers the image by moving it up or down.
o For resetting adjustments to the factory preset values, press
A/T to select "Reset", and then press ENTER.
o When connecting a PC to the HDMI terminal, the image
position will be automatically adjusted. It cannot be
manually adjusted.
o Adjustments are stored separately according to input
source.
o When a DTV channel is selected, the horizontal position
cannot be adjusted.
o The horizontal and/or vertical position may not be able to
be adjusted or it may be adjusted only to a certain degree.
Some input signals may have to be registered manually
to display properly. The pair of input signals (resolutions)
in the list below is not distinguishable when received.
ha such a case, you have to set the correct signal
manually. After setting once, it will display when the
same signal (resolution) is input again.
If024x768 f360x768J
o You can only select the "Input Signal" on the Setup menu
when receiving one of the 2 input signals listed above.
2O