LCD COLOR TELEVISION/ DVD VIDEO PLAYER MODEL LC-26AD22U In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS • • • • • • • • • • • • • • • • • • • • • • • CAUTION .............................................................................................................................. IMPORTANT SAFEGUARDS ...........................................
CAUTION THIS LCD COLOR TELEVISION EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS LASER RADIATION EXPOSURE. TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE.
IMPORTANT SAFEGUARDS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
IMPORTANT SAFEGUARDS (CONTINUED) 19) If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, conne
IMPORTANT SAFEGUARDS (CONTINUED) 25) Do not allow the product to output distorted sound for an extended period of time. It may cause speaker overheating and fire. 26) When you use the headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage. 27) Do not look into the opening of the disc slot or ventilation opening of the product to see the source of the laser beam. It may cause eye damage.
WHEN REPLACING DVD DECK [ When removing the DVD Deck ] Before removing Pick Up PCB and DVD MT PCB connector, the short circuit the position shown in Fig. 1 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. [ When installing the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD MT PCB connector. NOTE • Before your operation, please read “PREPARATION OF SERVICING”. • Use the Lead Free solder.
DISC REMOVAL METHOD AT NO POWER SUPPLY 1. Remove the Back Cabinet and Angle Deck. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.) 2. Slide the Belt Loading toward the arrow direction by hand to release the lock. (Refer to Fig. 1) 3. Take out the Disc from the DVD Deck. Be careful not to scratch on the Disc. DVD Deck Belt Loading Fig.
ABOUT LEAD FREE SOLDER (PbF) Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF printing on the PCB. (Please refer to figures.) Caution: • Pb free solder has a higher melting point than standard solder; Typically the melting point is 86°F~104°F(30°C~40°C) higher. Please use a soldering iron with temperature control and adjust it to 650°F ± 20°F (350°C ± 10°C). In case of using high temperature soldering iron, please be careful not to heat too long.
GENERAL SPECIFICATIONS G-1 TV System LCD LCD Size / Visual Size LCD Type Number of Pixels View Range Left/Right Up/Down Color System Speaker Sound Output G-2 DVD System Position Size Impedance Max 10%(Typical) Color System Disc Disc Diameter Drive Search speed Fwd Actual Rev Actual Slow speed Fwd Actual Rev Actual G-3 Tuning System Broadcasting System Tuner and Receive CH Intermediate Digital Frequency Analog G-4 Signal Preset CH Stereo/Dual TV Sound Tuner Sound Muting Video Signal RGB Si
GENERAL SPECIFICATIONS G-6 Regulation G-7 Temperature G-8 G-9 Operating Humidity Clock and Clock Timer Sleep Timer G-10 Remote Control Safety Radiation Laser Operation Storage Max Time Step Program Program On Timer Off Timer Game Timer Wake Up Timer Timer Back-up (at Power Off Mode) more than Unit Glow in Dark Remocon Remocon Format Format Custom Code Power Source Voltage(D.
GENERAL SPECIFICATIONS G-11 Features (TV) Auto Shut Off Auto Search Power On Memory Comb Filter Yes No No Yes 3 -D Game Position Auto Setup(Language/CH Program) Picture Setting(TV) AV Mode(Picture Preference) Brightness , Contrast , Color Tint Sharpness Color Temperature Cable Clear Backlight Picture Setting(PC) Brightness , Contrast HOR Position , VER Position Phase, Clock Red, Green, Blue Auto Adjust Backlight Audio MTS Tone Control (Bass/Treble/Balance) Stable Sound Surround BBE SRS WOW (SRS 3D/Focus
GENERAL SPECIFICATIONS HDMI Input VGA (640x480) 720x480i (4:3) 720x480i (16:9) 720x480p (4:3) 720x480p (16:9) 720x576i (4:3) 720x576i (16:9) 720x576p (4:3) 720x576p (16:9) 1280x720p 1920x1080i Component Input 720x480i (4:3) 720x480i (16:9) 720x480p (4:3) 720x480p (16:9) 720x576i (4:3) 720x576i (16:9) 720x576p (4:3) 720x576p (16:9) 1280x720p 1920x1080i Features (DVD) Video CD Playback SVCD Playback MP3 Playback JPEG WMA Digital Out Down Mix Out Closed Caption Screen Saver TV Screen (Dolby Digital) (MPEG)
GENERAL SPECIFICATIONS G-12 Accessories Owner's Manual Language w/Guarantee Card Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safeguard Dew/AHC Caution Sheet Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Adapter AC Cord (for AC Adapter) AC Cord (Flat Polarity Plugs) Cable Cramp Stand Stand Screw Hexagon Wrench AV Cord (2Pin-1Pin) Registration Ca
GENERAL SPECIFICATIONS G-13 Interface Switch Top Rear Indicator Terminals Side Rear G-14 Set Size G-15 Weight G-16 Carton G-17 Material Power (Tact) Channel Up/Menu Up Channel Down/Menu Down Volume Up/Menu > Volume Down/Menu < Menu Play Eject Skip+, Search+ Skip-, SearchStill/Pause Stop Main Power SW Input Select Main Power SW Power/Stand-By On Timer Video Input 1 Audio Input 1 S - Input 1 Video Input 2 Audio Input 2 S - Input 2 Video Output Audio Output Component Input 1 Analog Audio Componen
GENERAL SPECIFICATIONS G-18 Environment Environmental standard requirement Pb-free Measures for Whisker Rohs A2-7 Green procurement of SHARP Phase3(Phase3A) Yes Yes
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS 1 11 1 1 1-1: BACK CABINET (Refer to Fig. 1-1) SHIELD MPEG 1. Remove the 14 screws 1. 2. Remove the 7 screws 2. 3. Remove the Back Cabinet in the direction of arrow. (C) DVD Deck (B) 1 2 12 1 2 22 2 1 3 3 1 Pick Up PCB 3 2 1 3 1 DVD MT PCB 2 1 2 22 1 (A) 1 1 4 4 1 1 Short circuit using a soldering iron. Angle DVD-1 1 Back Cabinet (D) Fig. 1-2 Fig. 1-1 1-3: OPERATION PCB (Refer to Fig.
DISASSEMBLY INSTRUCTIONS 1-4: REMOCON PCB (Refer to Fig. 1-4) 4 4 1. Disconnect the following connector: (CP106). 2. Remove the 2 screws 1. 3. Remove the Remocon PCB in the direction of arrow. 2 2 1 3 Shield Digital (A) 1 1 Digital PCB Plate Jack Remocon PCB (B) Fig. 1-4 1-5: LCD BLOCK (Refer to Fig. 1-5) Fig. 1-6 1. Disconnect the following connectors: (CP406, CP1001 and CP2407). 2. Remove the Holder Panel. 3. Remove the 4 screws 1. 4. Remove the LCD Block in the direction of arrow (A). 5.
DISASSEMBLY INSTRUCTIONS 2-2: SWITCH PCB ASS'Y/GEAR MIDDLE/GEAR FEED/RACK FEED ASS'Y/FEED MOTOR (Refer to Fig. 2-2-A) 2. REMOVAL OF DVD DECK PARTS NOTE 1. Remove the Insulator (F). 2. Remove the Insulator (R). 3. Unlock the support 1. 4. Remove the Gear Middle. 5. Remove the screw 2. 6. Remove the Rack Feed Ass'y. 7. Remove the screw 3. 8. Remove the Switch PCB Ass'y. 9. Remove the screw 4. 10. Remove the Gear Feed. 11. Remove the 2 screws 5. 12. Remove the Feed Motor. 13. Remove the Gear Motor. 1.
DISASSEMBLY INSTRUCTIONS [ 6 pin FFC ] Gear Motor 40 ± 1mm Fold 8.0 ± 0.2mm Feed Motor Fold 60 ± 1mm Safety surface for pressing of the insert. Fig. 2-2-C Fig. 2-3-B Switch PCB Ass'y ~ FEED MOTOR ~ WHITE (4) BROWN (3) • Install wire from (1) to (4) in order. ~ SPINDLE MOTOR ~ YELLOW (2) GREEN (1) Fig. 2-2-D Traverse Ass'y Check Hook Check Hook Check Hook Check Hook • Loosen the wire in the direction of the arrow. Fig. 2-2-E 2-3: FFC WIRE HANDLING 1.
DISASSEMBLY INSTRUCTIONS 3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 3-3.) 3. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC REMOVAL NOTE 1. Put Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 3-1.
DISASSEMBLY INSTRUCTIONS INSTALLATION 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 3-8.) 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 3-5.) Thin-tip Soldering Iron IC Soldering Iron Fig. 3-8 5.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control for more than a the standard time in the appropriate condition. (See below chart.) Set Condition Set Key Remocon Key Standard Time TV mode VOL. DOWN (Minimum) 0 2 sec. Releasing of V-CHIP PASSWORD. TV mode VOL. DOWN (Minimum) 1 2 sec.
SERVICING FIXTURES AND TOOLS JG176 Up-Date Disc Ref. No. Part No. JG176 APJG176123 Remarks Parts Name Up-Date Disc Up-Date of the Firmware RE-WRITE FOR DVD FIRMWARE 1. Turn on the power, and set the DVD mode. 2. Confirm that the “No Disc” will be appeared on the screen. 3. Press both VOL. DOWN button on the set and Channel button (5) on the remote control for more than 2 seconds. 4. Press VOL. UP/DOWN button on the unit to check if all the keys on the unit do not function.
RE-WRITE FOR DIGITAL SOFT FIRMWARE JG176 USA HD DTV ROM DISC Ref. No. JG176 1. Part No. APJG176121 Remarks Parts Name 2007 USA DTV LCD ROM DISC Up-Date of the Firmware Copy the "update.dat" in CD to USB Flash Memory. Recommended USB Flash Memory • SanDisk Cruzer Mini USB Flash Drive 128Mb • SanDisk Cruzer Mini USB Flash Drive 256Mb • SanDisk Cruzer Micoro USB Flash Drive 128Mb • SanDisk Cruzer Micoro USB Flash Drive 256Mb • TwinMos ModileDisk3 128Mb (USB 2.0) • TwinMos ModileDisk3 256Mb (USB 2.
WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC, POWER ON total hours and MICON VERSIONcan be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0". Please refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding. 1. Turn on the POWER, and set to the TV mode. 2. Set the VOLUME to minimum. 3. Press both VOL.
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE NO. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION • Use an isolation transformer when performing any service on this chassis. • When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position.
ELECTRICAL ADJUSTMENTS 2-2: WHITE BALANCE 1. Place the set in Aging Test for more than 15 minutes. 2. Receive the gray scale pattern from the Pattern Generator. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "R DRIVE(N)". 5. Press the CH.
ELECTRICAL ADJUSTMENTS 2-4: Confirmation of Fixed Value (Step No.) Please check if the fixed values of each of the adjustment item is set correctly referring below. (ANT/AV/COLORSTREAM HD/PC/DVD/DIGITAL) AV ANT CVBS NO. COLORSTREAM HD S(Y/C) 480i 480p 720p HDMI 108i VGA 480i 480p PC 720p 1080i 640*480 DIGITAL DVD 720*400 800*600 1024*768 1280*768 1280*720 852*480 1360*768 480i 480p 720p 108i Step No.
ELECTRICAL ADJUSTMENTS 3.
TROUBLESHOOTING GUIDE (LCD SECTION) POWER DOES NOT TUNER ON Is F401 broken? Yes Change F401. No Is there voltage at pin 1 of IC402 6V? No Check IC402 and peripheral circuit. Yes Yes Is R412 broken? Change R412. No Is there voltage at pin 10 of IC401 19V? No Check IC401 and peripheral circuit. Yes Change DIGITAL PCB.
TROUBLESHOOTING GUIDE THE PICTURE APPEARS, BUT THE AUDIO DOES NOT APPEARS. (ATRFMODE) No Connect CP1001. Is CP1001 connected? Yes Is there signal at pins 1 and 4 of CP1001? Yes Change SP1001. No Is there signal at pins 2 and 5 of IC1001? Yes Check IC1001 and peripheral circuit. No Is there signal at pins 1 and 20 of IC1002? Yes Check IC1002 and peripheral circuit. No Is there signal at pins 28 and 30 of IC701? Yes Check IC701 and peripheral circuit.
TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR (1) No Does backlight shine? Is there voltage at pins 1, 2,3, 4and 5 of CP406 12V? No Check D436, D437 and peripheral circuit. Yes Yes No Is CD7201 connected? Connected CD7201. Yes Is there voltage at pin 28,29,30 and 31 of CP2407 12V? No Check Q3410 and peripheral circuit. Yes Is there signal at pins 7, 8, 10, 11, 13, 14, 16, 17, 19 and 20 of CD7201? Yes Change V2301(PANEL). No No Is there signal at IC2405? Change IC2405.
TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR (2) Is there signal at pins 33 and 35 of IC701? No Check IC701 and peripheral circuit. Yes Yes Check IC2401 and peripheral circuit. Is there signal at pins A9 and A13 of IC2401? No Yes Check IC2401 and peripheral circuit. Is there signal at C2528 and C2532? No Check C2528, C2532 and peripheral circuit.
TROUBLESHOOTING GUIDE THE COLOR DOES NOT APPEAR Is setting of color normal? No Adjust the color. Yes Is the color signal received? No Receive the color signal. Yes Is there color signal at pins A9 and A13 of IC2401? Yes Change DIGITAL PCB. No Is there color signal at pins 33 and 35 of IC701? No Check Q701,Q702 and peripheral circuit. Yes Check IC701 and peripheral circuit.
TROUBLESHOOTING GUIDE (DVD SECTION) DOES NOT DISPLAY DVD PICTURE Does this display logo picture? Yes Check the disc. No Does this have signal at pins 149 and 151 of IC4001? Yes Check pins 12 and 16 of CP8501 and peripheral circuit. No Does IC4001 gets P.CON+3.3V and P.CON+1.8V? Yes Change IC4001. No Check P.CON+3.3V and P.CON+1.8V line.
TROUBLESHOOTING GUIDE DISC DOES NOT EJECT Does OSD appear on the screen? No Is remote key set effectively? No Check pins AD18 and AF19 of IC2401 and peripheral circuit. No Check IC2301 and peripheral circuit. Yes Yes Check pins 138 and 139 of IC4001 and peripheral circuit. Does this eject disc at change DVD DECK? Yes Change DVD DECK. No Does this have signal at pins 4 and 5 of CP2302? Yes Does this have signal at pins 1 and 2 of CP2302? Yes Change IC4001. E-7 No Change IC2301.
TROUBLESHOOTING GUIDE DOES NOT PLAY DVD Change DVD DECK. No Does this display "INCORRECT DISC"? Yes No Does CD2001 connect with CP2301 correctly? No Connect CD2301. Does this display reading mark? No Change IC4001. Yes No Does disc rotate? Change DVD DECK. Yes Change IC4001. E-8 Yes Is the voltage between JG017 and JG018 less than 0.
TROUBLESHOOTING GUIDE DOES NOT PLAY CD Change DVD DECK. No Does this display "INCORRECT DISC"? Yes No Does CD2001 connect with CP2301 correctly? No Connect CD2301. Does this display reading mark? No Change IC4001. Yes No Does disc rotate? Change DVD DECK. Yes Change IC4001. E-9 Yes Is the voltage between JG019 and JG018 less than 0.
TROUBLESHOOTING GUIDE NO SOUND DVD/CD ANALOG AUDIO Does this have signal at pins 8 and 10 of CP8501? Yes Refer to "LCD SECTION". No Does this have signal at pins 1 and 7 of IC8501? Yes Check pins 1 and 7 of IC8501 and peripheral circuit. No Does this have signal at pins 113, 114, 115 and 116 of IC4001? Yes Change IC8501. No Change IC4001. NO SOUND DVD/CD DIGITAL AUDIO Does this have signal at pin1 of CP8501? Yes Check J706 and peripheral circuit. Yes Check IC4001 and peripheral circuit.
DVD BLOCK DIAGRAM DVD LOADER DSM2 LCD BLOCK E C, D MD_DVD, MD_CD TX RF, A, B, C, D, E, F RX START_SW OPU DVD_CD, DVD_LD, CD_LD SPINDLE/ STEPING/ SLED MOTOR TR+/-, FO+/-, MOT_LD+/-, MOT_SLED+/MOT_SPDL+/- Motor Drive IC2301 LA6565VR-TLM-E SPINDLE/SLED/ FOCUS/TRACK_PWM, TRAY_CLOSE/OPEN MPEG/MICON/DSP/RF_AMP IC4001 ZR36966ELCG-D SPDIF DVD C DVD Y DVD RESET DVD POWER SPDL_SENS+/B HOME, TIN_SW, TOUT_SW APWM_L+/-, APWM_R+/HA0~A19, HD0~D15, MEMCS0, RD, WR AUDIO AMP IC8501 NJM4565M C F-1 AUDIO R
POWER BLOCK DIAGRAM L402 F401 L401 3 4 1 2 CD3805 AC IN 3 4 1 2 J401 TRANSFORMER T402 D425 D427 D430 D431 2 3 1 4 1 + C424 3 7 POWER SW IC402 D + C404 + 5 Vcc FB Vdd 4 2 FEED BACK IC410 PS2561AL1-1-V（W) 1 POWER SW IC401 MP2A5060 18 CP411__16. POWER Q416 D40 D41 C403 Vcc Q1 CP411__14,15. AT+5V 5 RERAY RY401 ALKS329_A6 10 8 P.GND 8 4 1 3 2 REGULATOR IC404 KIA431A-AT 1 3 D465 CP410__1,2. DVD+12V TRANSFORMER T401 2 1 CP411__1,2. SOUND+B 7 1 CP411__8,9.
POWER(DIGITAL PCB) BLOCK DIAGRAM CP3401 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 SOUND AMP IC1001 AN17808B SOUND +B SOUND GND REG+9V IC3404 P.CON +9V BA00BC0WFP AV SW IC701 AN15853B-E1 Q3410 LCD +B RSQ035P03 SW +12V PANEL V2301 LK255T3LZ5A GND STAND-BY_H POWR_ON_H LIGHTE_CTL INVERTER_H AD CONVERTER IC6601 MST3583M-LF-110 Q3406 2SB1132 AT +5V P.CON +5V SUB MICON IC101 OEC6088A POWER FAIL GND Q3405 RSS065N03FL16TB IC3403 BD3504FVM VDDC 1.
SIGNAL BLOCK DIAGRAM IN PC/HDMI AUDIO IN J4201MSJ-2000B_AG PC/HDMI AUDIO L/R SIF IN TUNER TU2801 ENG36E03KF IN CVBS IN 1 J703 RCA-349-00C-02 IN CVBS IN 2 J702 RCA-349-00C-02 AUDIO SW L/R IC1003、1004 MM1501XNRE USA STEREO IC901 AN5832SA-E1V Analog Tuner AUDIO L/R AUDIO SW L/R IC704、705 MM1501XNRE PC/HDMI/RF SW AUDIO L/R SW AUDIO L/R 2 DIGITAL AUDIO L/R TONE CONTOROL IC IC1002 NJW1173V TONE AUDIO L/R DIGITAL RF (IF) ANALOG RF(CVBS) SOUND AMP IC IC1001 AN17808B AMP L/R LVDS IC IC2405 ICSV3
A B C D E F G H MPEG/MICON/DSP/RF_AMP SCHEMATIC DIAGRAM (DVD MT PCB) RF OPU_B OPU_A OPU_F SPDL_SENS+ OPU_E SPDL_SENSOPU_D OPU_C VC C4086 0.001 B C4085 0.
A B C D E F G H MEMORY SCHEMATIC DIAGRAM 8 8 (DVD MT PCB) 1 0.7 2 0.6 3 0.6 4 1.0 5 2.5 HA11 0.7 HA10 1.0 HA15 HA14 HA13 7 0 B4007 4.7K 2.4 R4040 HA0 C4063_2 2.9 6.3V 220 YXF MEMCS0 RD WR MEMCS0 A5 DE# A4 VSS A3 CE# A2 A0 A1 1.7 HA7 0 HA6 1.7 HA5 1.7 HA4 1.7 HA3 1.0 HA2 2.6 HA1 SD_A9 0 SD_A8 0 SD_A7 1.6 SD_A6 1.6 SD_A5 1.6 SD_A4 1.
A B C D E F G AUDIO/VIDEO SCHEMATIC DIAGRAM 8 FROM/TO MPEG/MICON/DSP/RF_AMP C8506 1uHNLV25 3 4 Y Y Y G DAC1 V U V U (V) (U) R B D DAC3 C (C) C - E DAC5 DAC4 DAC2 CVBS CVBS CVBS CVBS 6.3V 470 ZLH 59 6 6 DAC_VIDEO_A C8524_1 C8511 W820 SH8501 YQ-36 FROM/TO REGULATOR2 C8512 1uHNLV25 DAC_A[Y]_VIDEO 6.
A B C D E F G H MOTOR DRIVE SCHEMATIC DIAGRAM 8 8 CD_LD DVD_LD MD_CD (VR_DVD) DVD_CD MD_DVD (VR_CD) VC (DVD MT PCB) C2350 DSM2(06SD) 0.1 B JG014 C2318 0.001 B C2316_2 16V47 YXF 0.1 F C2346_2 R2335 3.3K 390 R2336 10K 1K R2324 W861 R2319 4.7K TP2318 R2327 5.6K TP2319 15K R2321 R2326 R2309 100 +-1% R2334 TP2320 (M_GND) SH2301 YQ-36 P.CON+A5V_D P.CON+3.3V_D (D_GND,M_GND) GND C2306 0.1 F 0.1 B 2 C2302 0.1 B R2303 2.2 C2303 0.1 B R2304 2.2 21 1.
A B C D E F G H REGULATOR2 SCHEMATIC DIAGRAM 8 8 (DVD TM PCB) DVD_POWER_H FROM/TO POWER_PCB L3005 CP3001(CP410) A2001WR2-4P 60 11.9 11.9 6.9 0.1 F V_IN 2 0 5.9 GND (D_GND,M_GND) COM V_OUT 1 3 FROM/TO MEMORY 5.1 P.CON+A5V_D P.CON+3.3V_D GND (D_GND) 1 F 2.2uHNLV25 C3018 C3019_2 L3003 6.3V 220 YXF 0.1 F SW Q3004 6.02 KTA1505S-Y-RTK/P C3017 SW 6.02 Q3003 KTC3875S_Y_RTK 0.04 C3016_2 6.4 6 P.CON+3.3V_D GND (M_GND) 5 0.1 B C3005 68K R3006 R3004 10K +-1% P.
A B C D E F G H 8 8 OPERATION2 SCHEMATIC DIAGRAM 7 7 (OPERATION2 PCB) 6 EVQ21505R EVQ21505R 5.6K SKIP+_2 SW2254_2 R2255 2.2K EVQ21505R KEY_1 R2254 1.
A B C D E F G H ASIC SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 FROM/TO LVDS X242 ATSC/CLEAR CABLE ASIC IC IC2401 X242 (1/14 VDD) HS2401 763WAA0359 (4/14 OSC) 0 0 0 DVIDATA7 3.3 DVIDATA8 3.3 DVIDATA9 3.3 DVIDATA10 3.3 DVIDATA11 3.3 DVIDATA12 3.3 DVIDATA13 3.3 DVIDATA14 3.3 DVIDATA15 3.3 DVIDATA16 3.4 DVIDATA17 3.4 DVIDATA18 3.4 DVIDATA19 3.4 DVIDATA20 3.4 DVIDATA21 3.3 DVIDATA22 3.4 DVIDATA23 3.
A B C D E F G H SDRAM SCHEMATIC DIAGRAM 8 8 (DIGITAL PCB) 4-LAYER 6-LAYER CEF272A CEF251A CEF276A CEF254A A12 MEM_AA12 MEM_AA12 A11 MEM_AA11 MEM_AA11 DDR2 PIN Name ATSC/CLEAR CABLE ASIC IC IC2401 X242 (5/14 SDRAM) MEM_DQA1 0 MEM_DQA2 0 MEM_DQA3 0 MEM_DQA4 0 MEM_DQA5 0 MEM_DQA6 0 MEM_DQA7 0 MEM_DQA8 0 MEM_DQA9 0 MEM_DQA10 0 MEM_DQA11 0 MEM_DQA12 0 MEM_DQA13 0 MEM_DQA14 0 MEM_DQA15 0 MEM_DQM0# 0 MEM_DQM1# 0 MEM_QS0 0 R24 DQA0 MAA0 U26 P24 DQA1
A B C D E F G H FLASH SCHEMATIC DIAGRAM (DIGITAL PCB) NFIO0 NFIO1 NFIO2 NFIO3 NFIO4 NFIO5 NFIO6 8 NFIO7 8 C2503 0.1 B 7 NC 0 NC 0 NC 0 NC 0 0 0 0 NC 0 0 NC 0 NC 0 0 NC 0 NC 0 3.3 NC 0 0 0 0 NC 0 NC 0 0 NC 0 NC 0 7 USB_P_B 0 15K USB_N_B 0 NC FROM/TO MICON NC CTSA# AE17 3.
A B C D E F G H FRONT END SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 7 VI_REFP1 GPIOC(1) C6 C9 VI_BYPASS1 GPIOC(2) B6 GPIOC(3) A6 GPIOC(4) C7 GPIOC(5) B7 GPIOC(6) A7 GPIOC(7) C8 A10 ADC1_AVSS_1 GPIOC(8) AD21 B9 ADC1_AVSS_2 GPIOC(9) AE21 D10 VI_AVDD33 GPIOC(11) AD20 C2520 1 B GPIOC(13) AF20 GPIOC(14) AD19 NC NC NC 21 75 +-1% DVD_RESET 2.2uH NLV25 C2517 PC/HDMI_H C2528 220P CH R2433 C2505 SW_C_OUT 3 220P CH L2403 TU_VIDEO SIF C2532 SW_Y/CVBS_OUT NC 0 0 1.
A B C D E F G H AV OUT SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 ATSC/CLEAR CABLE ASIC IC IC2401 X242 (13/14 VIDEO ENCODER) 7 C2560 0.1 B 2.5 10 C C2554 B2418 FCM1608KF-151T06 C2561 2.5 FCM1608KF-151T06 0.1 B 10 C C2555 B2419 0 0 C2562 0.1 B 2.5 0 C2563 6 0.1 B 2.5 B2420 C2564 0 C2565 2.5 0.1 B 1 B C2559 10 C 0.1 B 2.
A B C D E F G H POWER3 SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 REG+9V IC IC3404 BA00BC0WFP FROM/TO AV OUT DTV+B 23 DTV+B R3441 4 3 2 1 5 6 7 8 3.3K +-1% 22 B 22 B C3428 LIGHT_CTL B3405 FCM1608KF-102T02 INVETER_H 4 5 6 B3408 HCB3216KF-391T20 AT+5V S D D C3437 10 B 22 B 22 B C3427 C3426 C3433 2V 150 CD 220 C3421 R3418 C3423 0.022 B R3412 390 +-1% 2.2K +-1% 3.9K +-1% 1 B R3415 R3413 1 2 R3411 C3410 2.2 B C3419 C3414 3 1.
A B C D E F G H LVDS SHEMATIC DIAGRAM (DIGITAL PCB) 8 1 3.3 Vcc TxIN4 TxIN5 TxIN3 3.3 R4 3.3 R3 G0 3.3 55 TxIN2 TxIN6 GND TxIN7 7 FROM/TO PANEL 3.3 R2 LCD_SH/QD CP2407 20389-Y30E 0 3.3 TxIN27 TxIN9 3.3 R1 3.3 R0 GND W823 C2568 52 TxIN0 51 5 TxIN8 50 G2 3.3 TxIN1 7 G1 GND 6 LCD+B 0 1 B 3.3 54 R5 53 3.3 4 R7 3 0.1 B W870 3.3 W867 R6 3.3 TxOUT0- Vcc 49 LVDSGND TxIN10 48 C2593 3.3 9 G6 8 R2522 0 4.7K G3 3.3 G4 3.
A B C D E F G H VIDEO AD CONVERTER SCHEMATIC DIAGRAM (DIGITAL PCB) W853 NR6603 4D02WGJ0330TCE NR6602 4D02WGJ0330TCE NR6601 4D02WGJ0330TCE DVIDATA20 DVIDATA21 DVIDATA22 DVIDATA23 DVIVSYNC DVIHSYNC DVIDE DVICLK 8 DVIDATA16 DVIDATA17 DVIDATA18 DVIDATA19 8 7 7 C6636 0.1 B C6630 0.1 B 3.3 64 62 61 60 59 58 57 56 3.3 55 3.3 54 0 53 63 GND VDDP 0 2.5 VDDC 3.3 DATACK 3.3 SOGOUT 3.3 48 3.3 47 3.3 46 3.3 45 3.3 44 3.3 43 3.3 0 NC 0 NC 3.3 3.3 42 41 52 51 50 49 3.
A B C D E F G H MICON SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 7 C_SYNC REMOCON_IN CP101 100 AFT 4.7K R119 FROM/TO ASIC KEY_A KEY_B R107 2.2K DVD_POWER R103 DVD_RESET R108 2.2K C_SYNC START_SW LCD-H FROM/TO AV SWITCH/JACK INVETER_H POWER_ON_MUTE_H 7 EEPROM_SCL DTV_RESET EEPROM_SDA 5.0 5.0 5.0 5.0 R112 10K TX_[X242] RX_[X242] START_SW 0 W836 5.0 4 EEPROM_SDA EEPROM_SCL 5.0 VSS SCL A2 0 WP A1 0 VCC A0 0 0 3.0 R110 4.7K 5.0 R111 4.7K 0 RX_[X242] 5.
A B C D E F G H AV SWITCH/JACK SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 0 NC DVD_POWER MODE SDA/SAPID 5.0 75 I2C_DATA 0.001 B W801 L+R REF NC PLL 3.4 SW_C_OUT PILOT DET 3.4 R901 C918 3.3K C915 0.22 B 0.33 B 16V100 V-S C931 P.
A B C D E F G H SOUND SCHEMATIC DIAGRAM 8 FROM/TO FRONT END MUTE SW Q1003 KTC3875S_Y_RTK 5.0 C1016 0 1B HCB1608KF-181T20 GND 3 3 4 4 SP1002 S0412F03 6 4.7K R1031 CD301 CU145005 STANDBY SW Q1005 KRC103SRTK 5.0 3.4 C1012_1 W826 W825 0 35V1000 MHE_P SOUND_GND P.CON+9V SPEAKER 15 GND P.CON+5V SP1001 S0412F03 6.8K 6.8K R1012 0 SOUND+B 5 2 3.9K MUTE SW Q1004 KTC3875S_Y_RTK 1 2 SP OUT R 5.
A B C D E F G H INTERFACE_HDMI IC SCHEMATIC DIAGRAM (DIGITAL PCB) 8 8 D3605 VDD5_PS 4 DVIHSYNC R3617 33 3.3 C3619 6.3V 22 V-S NC 3.3 C3626 NC 3.3 0.001 B NR3603 4D02WGJ0330TCE DVIDATA8 DVIDATA9 DVIDATA10 DVIDATA11 3.3 3.3 3.3 3.3 1.8 NR3604 4D02WGJ0330TCE DVIDATA12 DVIDATA13 DVIDATA14 DVIDATA15 0.001 B 3.3 3.3 3.3 C3643 3.3 B3605 FCM1608CF-600T06 3.3 3.3 C3647 0.001 B 3.3 3.3 3.3 FROM/TO AV OUT I2SSCK_IND I2SWS_IND I2SSD_IND C3644 0.001 B 3 C3667 0.
A B C D E F G H PC JACK SCHEMATIC DIAGRAM (DIGITAL PCB) 8 2 EBMS160808A102_RDC45 R L R4208 B4203 EBMS160808A102_RDC45 C4209 1K 1B R4214 HDMI AUDIO IN J4201 MSJ-2000B_AG(O87) B4201 R4209 1 B 3.0 L4203 7 22uH NLV25 FROM/TO POWER3 8.5 3.0 8.5 C4210 1K P.CON+9V P.CON+5V 2.4 BUFFER Q4201 KTC3875S_Y_RTK GND 50 5.4 51 0.001 B C4207 EBMS160808A102_RDC45 R4221 L 3 180K R 180K 7 BUFFER Q4203 KTC3875S_Y_RTK B4206 1 8 6 C4216 16V100 V-S 4.7K R4224 220K R4222 4.
B E F G POWER1 SCHEMATIC DIAGRAM CHASSIS GND CP413 003P-2100 0 NC 2 9 1.2 NC 0 C441 R454 180 +-1% R455 +-1% R456 2.2K 10K 1/4W R522 C433 2.2K +-1% REFERENCE R444 2.2K C431 R521 10K 1/4W 2 D448 1SS133 1SS133 D456 D449 D446 2 C434 1 3 500V0.001 B 1SS133 D437 YG862C10R 1SS133 INV_SW+24V 24.2 GND R442 1SS355 SH406 YQ-36 2.4 1K 0.01 B R459 C467 R457 220 1/4W 50V 47 MHE_P 0 PROTECT Q415 KTA1504S_Y_RTK MTZJ3.3B C445 19.4 3.5 D450 1 6.
A B C D E F G H POWER2 SCHEMATIC DIAGRAM 22K R480 FROM/TO POWER1 4.6 100 1/4W 0 GND GND_S AT+5V POWER_FAIL P.CON+5V NC SW+5.5V C458 NC 50V10 YXF_P R487 4.7K 1/4W R486 100 1/4W SOUND+B[SW] 3 +24V 4 +24V 5 GND 6 GND 7 GND 8 GND 9 GND 10 7 Analog/Dimming 11 N.C(open) 14 6 14PIN CD403_1 CU2E0601 LCD+B REG BLOCK FROM/TO DVD_PCB LIGHT_CTL 1.6A 125V LIGHT_POWER_H F404 SW+12V 13.5 12.4 EV+17V REG Q422 KTB1151 12.8 5 R491 20N_1600FS 1.
A B C D 8 E F G H 8 OPERATION/REMOCON SCHEMATIC DIAGRAM (REMOCON PCB) 7 Vout 7 FROM/TO DIGITAL_PCB OS2201 ROM-V338TAO CP2201(CP106) A2001WR2-5P 1 GND 2 REMOCON IN 1 GND 2 AT+5V 3 STANDBY LED 4 R2208 B+ 3 0.1 B 0.1 B C2207 C2206 G STANDBY/POWER D2201 LTL-1BEFJ-002A R C2205 6.
A B C D E F G H SW SCHEMATIC DIAGRAM 8 8 7 7 (SW PCB) 6 6 SW2 ESE22MH22 CD2301 2H061605 1 GND(SW) 2 5 PICK UO INNER LIMIT SWITCH 3 FEED MOTOR(-) 4 FEED MOTOR(+) 5 SPINDLE MOTOR(-) 6 SPINDLE MOTOR(+) M M M2602 BCZ3B05 M2601 JCV9B12 5 PCB640 DED020 4 4 3 3 2 2 THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY ARE PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NOTE: THIS SCHEMATIC DIAGRAM IS T
A B C D E F G INTERCONNECTION DIAGRAM CP2251 CP2204 GND 1 CP103 CD2202_1 1 GND GND 1 1 GND KEY B 2 2 KEY B KEY_1 2 2 KEY_1 KEY A 3 3 KEY A H2 1 5 E H1 4 NC H1 3 H2 2 E 4 H3 5 1 NC H1 3 2 E H2 4 H3 S+COAXIAL J706 E 3 5 1 8 7 E H 1 8 9 3 E 4 5 CP3401 2 6 7 CP2401 6 CP2201 REMOCON IN CD2201_1 1 1 2 2 REMOCON IN AT+5V 3 3 AT+5V STANDBY LED 4 4 STANDBY LED POWER ON LED 5 5 POWER ON LED G R 1 B+ 3 GND 2 OS2201 1 SCL
WAVEFORMS FRONT END 2ms 0.5V 2ms 200mV 1 1ms 200mV 8 15 AV SWITCH/JACK 2ms 0.5V MICON 2ms 200mV 2 50ns 500mV 9 16 SOUND 10µs 0.5V VIDEO AD CONVERTER 0.5ms 1.0V 3 2ms 0.5V 10µs 100mV 10 17 50µs 1.0V 4 2ms 0.
WAVEFORMS ASIC 20µs 500mV 200ns 1.0V 22 2µs 2.0V 54 61 MEMORY １00µs 500mV 20µs 500mV 23 LVDS 55 AUDIO/VIDEO 10µs 2.0V 200µs 1.0V 24 56 PC/JACK 2ms 200mV 200µs 1.0V 50 2ms 200mV 57 10µs 200mV 51 58 MPEG/MICON/DSP/RF_AMP 10ns 500mV 10µs 100mV 52 59 REGULATOR 2 １00µs 500mV 2µs 2.0V 53 60 NOTE: I-2 The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
MECHANICAL EXPLODED VIEW 111 104C 211 104C 211 115 113 208 206 208 206 208 208 206 208 104C 211 104A 102B 211 104C 103 206 208 208 102E 104C 103A 103A 208 103C 104 208 208 103B 209 102E 102C 208 102A 208 208 208 202 102D 214 119 202 202 201 102F 201 138 102 107 207 207 213 207 106 120 120 207 207 207 136 207 130 109 120 207 205 123 207 PCB240 (POWER PCB ASS'Y) 207 PCBDH0 (DIGITAL PCB ASS'Y) 135 133 121 107 203 204 206 206 202 202 207 131 202 202 202
MECHANICAL EXPLODED VIEW (PACKING DIAGRAM) CD3805 HOLDER CORD POLYBAG INSTRUCTION INSTRUCTION BOOK(E/F/S) INFORMATION SHEET REGISTRATION CARD(SHARP) TM101 CLEANING CLOTH PACK PACKAGE TOP PACKAGE STAND-TOP PACKAGE STAND-BOTTOM PACKING SACK SCREW LAMIFILM BAG GIFT BOX SHEET BARCODE PACKAGE BOTTOM J1-2
MECHANICAL EXPLODED VIEW (PACKING DIAGRAM) PACKAGE STAND-TOP PACKING SACK (791WHA0125) SCREW PACKING SACK (791WHA0126) PACKAGE STAND-BOTTOM J1-3
DVD DECK EXPLODED VIEW 600 601 608 CD2001 M2602 603 606 703 Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more. If the repair is needed, replace the DVD MECHA ASS'Y. 605 703 702 702 607 AA 605 703 701 602 SW2 604 704 PCB640 (SW PCB ASS'Y) 705 CLASS PART NO. PART NAME GREASE Y315061000 G-555G CD2301 NOTE: Applying positions AA for the grease are displayed for this section. Check if the correct grease is applied for each position.
MECHANICAL REPLACEMENT PARTS LIST REF. NO. PART NO.
DVD DECK REPLACEMENT PARTS LIST REF. NO. PART NO. ! 600 A5Z001B650 DVD MECHA ASS'Y A5Z001B650 601 602 603 604 605 606 607 608 92SBB0033A 92AAA0017A 92P100088A 92P100117A 92P200017A 92P200018A 92P100116A 800WFAA008 LOADER SUB ASS'Y FEED RACK ASS'Y GEAR,MOTOR GEAR,MIDDLE INSULATOR, F INSULATOR, R GEAR,FEED CUSHION C DLM1D29-31 701 702 703 704 705 92P700007A 814011723U 816112080U 813381750U 811022080U SCREW,GEAR FEED SCREW,PAN SEMS.
ELECTRICAL REPLACEMENT PARTS LIST REF. NO. PART NO.
IC701 IC702 IC703 IC704 IC705 IC901 IC1001 IC1002 IC1003 IC1004 IC2401 IC2402 IC2404 IC2405 IC2407 IC2408 IC2801 IC3401 IC3402 IC3403 IC3404 IC3405 IC3408 IC3601 IC3602 IC6601 I01F05853B I5CJ031570 I0QF025840 I0UF015010 I0UF015010 I01FF58320 I0FSP7808B I5AFF11730 I0UF015010 I0UF015010 IFNMEX2420 IGGM005120 I0QF0580V0 IF8F0385A0 S5Z203EF02 S5Z203EE02 I03D979950 I0GF95ZN10 I07F078200 I57F035040 I07F0C0WF0 I07F078200 I07F078200 IG1F090250 S5Z203EE03 IFSK035830 IC IC IC IC IC IC IC IC IC IC IC IC IC IC MEMORY
B701 B702 B703 B704 B705 B706 B708 B709 B710 B711 B712 B713 B714 B715 B716 B717 B718 B719 B720 B721 B722 B723 B1001 B1004 B1005 B1009 B2401 B2402 B2403 B2404 B2405 B2406 B2407 B2408 B2409 B2418 B2419 B2420 B2421 B2422 B2423 B2430 B2501 B2502 B2503 B2504 B2801 B2802 B2803 B2804 B3402 B3403 B3404 B3405 B3406 B3407 B3408 B3409 B3410 B3601 B3602 B3603 B3604 B3605 B3610 B3611 B3613 B4201 B4202 B4203 B4204 B4205 B4206 024HC51513 024HC51513 024HC51513 024HC51513 024HC56005 024HC51023 024HC51023 024HC51023 024HC51
B6601 B6602 B6603 B6604 B6605 024HC51513 024HC51513 024HC51513 024HC51513 024HC51513 CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS FCM1608KF-151T06 FCM1608KF-151T06 FCM1608KF-151T06 FCM1608KF-151T06 FCM1608KF-151T06 L701 L702 L2401 L2403 L2802 L3601 L3602 L3603 L3604 L4203 L4204 0216S8470K 0216S8470K 0216SD2R2J 0216SD2R2J 0216SD330J 02D6000068 02D6000068 02D6000068 02D6000068 0216SD220J 0216SD220J COIL COIL COIL COIL COIL COIL CHOKE COIL CHOKE COIL CHOKE COIL CHOKE COIL COIL 47 UH 47 UH 2.
*** OTHERS *** CP2407 CP4201 06G3VWT01A CONNECTOR PCB SIDE 06G2S21501 CONNECTOR PCB SIDE 20389-Y30E D229FD015G107BY SH3401 SH3402 SH3403 SH3404 SH3405 126D000044 126D000044 126D000044 126D000044 126D000044 YQ-36 YQ-36 YQ-36 YQ-36 YQ-36 TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN DVD MT PCB ASS'Y *** PCB *** PCB130 A5Z203E130 DVD MT PCB ASS'Y DMF093A *** DIODES *** D2303 D2304 D3001 D3002 D3003 D4002 D4003 D4005 D4008 D8510 DD7R0S3550 DD7R0S3550 DD1R24D500 DD1R24D500 DD1R24D5
B4013 B4014 B4015 B4016 0246C51024 0246C51024 0246C51024 0246C51024 CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT MMZ1608R102CT L3001 L3002 L3003 L3004 L3005 L8502 L8504 02120K101M 02120K101M 0216SD2R2J 02167E220K 0216SD2R2J 0216SD1R0J 0216SD1R0J COIL COIL COIL COIL COIL COIL COIL 100 UH 100 UH 2.2 UH 22 UH 2.
C449 C453 C463 E7EYF2102M CE E7EYF2102M CE CD39E0M13M CC 1000 UF 16V 1000 UF 16V 0.
Q403 Q404 Q405 Q406 Q407 Q408 Q409 Q410 Q412 Q415 Q416 Q417 Q418 Q420 Q421 Q422 Q423 Q424 Q425 Q433 Q434 TCAA3875SY TCAA3875SY TCAT03209Y TCAA3875SY TAAT01281Y TCAA3875SY TCAA3875SY TJ7M50P030 TCAA3875SY TAAA1504SY TAAA1504SY TAAT01241Y TNAAA05001 TCAA3875SY TAAT01281Y TBA0011510 TCAA3875SY TNAAB05003 TNAAB05003 TCAA3875SY T25F035630 TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON FET TRANSISTOR SILICON TRANSISTOR SILICON
*** OTHERS *** EL2401 EL2402 124116281A 124120301A EYE LET EYE LET XRY16X28BD XRY20X30BD SH401 SH402 SH403 SH404 SH405 SH406 SH407 SH408 126D000044 126D000044 126D000044 126D000044 126D000044 126D000044 126D000044 126D000044 TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN TERMINAL PIN YQ-36 YQ-36 YQ-36 YQ-36 YQ-36 YQ-36 YQ-36 YQ-36 OPERATION PCB ASS'Y *** PCB *** PCB270 A5Z203E270 OPERATION PCB ASS'Y CEF274A *** SWITCHES *** SW2201 SW2202 SW2203 SW2204
CUS151 800WFAA007 CUSHION B SP1001 SP1002 070Y056003 070Y056003 SPEAKER SPEAKER S0412F03 S0412F03 TM101 076B0MR030 TRANSMITTER ETR0088-010171 V2301 09E4126009 LCD LK255T3LZ5AZ RESISTOR RC.................. CARBON RESISTOR CAPACITORS CC.................. CERAMIC CAPACITOR CE.................. ALUMI ELECTROLYTIC CAPACITOR CP.................. POLYESTER CAPACITOR CPP................ POLYPROPYLENE CAPACITOR CPL................ PLASTIC CAPACITOR CMP............... METAL POLYESTER CAPACITOR CMPL...
COPYRIGHT © 2007 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. Apr.
