Specifications

VIDEO MONITORS
555
THE PROFESSIONAL’S SOURCE [phone] • FAX: [phone]
1•800•947•9901
PHOTO - VIDEO - PRO AUDIO
SONY
Exclusive Features of the PVM-5041Q/8042Q/8045Q Only
Monitors and Accessories
PVM-5041Q ..............................979.95
PVM-8040 ..................................579.95
PVM-8042Q ..............................699.95
PVM-8045Q ..............................979.95
VF-504 ENG kit for 5041Q........116.95
VF-505 ENG kit for 8042/8045..109.95
MB-507 Rackmount bracket ......144.95
MB-509 Blank panel for MB-507..88.95
Sony NP-1B 2.3 Ah Nicad............79.95
IDX NP-23 2.3 Ah Nicad ............69.95
BC-1WD Battery Charger/Discharger
For 4 NP-1A/B ............................634.95
Porta-Brace MO-8044
Lightweight Field Monitor Case ..169.95
■ They have component inputs (Y/R-Y/B-Y
or RGB) and are fully compatible with
NTSC, PAL, SECAM and NTSC 4.43.
■ External sync inputs for synchronization
with other equipment. These monitors
can also accept sync on the green signal
of an RGB input which is automatically
selected when fed to the monitor.
■ They offer normal scan and underscan
selection. In underscan mode the size of
the screen is reduced so that the entire
active picture area is displayed.
■ Pulse cross function allows viewing of the
blanking area and sync/burst timing by
displaying the horizontal and vertical
intervals in the center of the screen.
■ Their picture aspect ratio can be switched
between 4:3 and 16:9 depending on the
input signal. On the 8045Q/8042Q, the
16:9 switch is located on the front panel.
On the 5041Q aspect ratio is selected
with the slide switch mounted on the rear
panel.
■ Blue Only mode provides monochrome
display allowing VCR noise inspection
and chroma/phase adjustment.
■ Pulse cross, underscan and external sync,
together with input selection can be oper-
ated from a custom-made selector when
connected to the remote input with the
supplied mini-DIN 8-pin connector.
Tally on/off can also be controlled.
AC/DC Operation
■ As well as operating from an AC power
source, these monitors can also be DC
powered for field operation. The PVM-
5041Q can be operated from a single
NP-1B battery pack, the 8-inch moni-
tors from one or two NP-1Bs.
■ When the battery voltage becomes low, a
power LED starts blinking as a warning
indication. The monitors will automati-
cally shut themselves down before the
battery is completely worn out.
■ 12-volt DC input so they can be powered
by car battery or belt pack. There is also a
dedicated Anton Bauer Gold Mount for
them.
■ Optional VF-504 (5041Q) and VF-505
(8042/8045Q) ENG kit contains a moni-
tor hood and cord reel for operational
convenience in the field.
PVM-8042Q/8045Q Only
Bias and Gain controls are accessible on
their front panel allowing fine adjustment
of white balance to be done from the
front of the monitor while observing the
screen. They also offer a manual degauss
switch on their front panel.
PVM-5041Q Only
Weighing only 12 lbs., the PVM-5041Q
is easily carried via it’s built-in handle. It
also has a built-in monitor stand to pro-
vide easy viewing.
Features At A Glance
PVM-8045Q/5041Q PVM-8042Q PVM-8040
Color System NTSC/PAL/ NTSC/PAL/ NTSC
SECAM/NTSC 4.43 SECAM/NTSC 4.43
Resolution 450 Lines 250 Lines 250 Lines
Composite Video Inputs 221
S-Video Input 111
RGB/Component Input Yes (BNC x3) Yes (BNC x3) —
Audio Inputs 3/2 3 1
External Sync Yes Yes —
Switchable Aspect Ratio 16:9/4:3 16:9/4:3 —
Tally/Remote Yes Yes —
DC Operation Yes Yes —
Underscan Yes Yes —
H/V Delay Yes Yes —
Blue Only Yes Yes —
Bias/Gain Control Yes Yes —
Rack Mount Bracket MB-507 MB-507 MB-507
Monitor ENG kit VF-505/VF-504 VF-505 —
DC-L10 Battery Adapter Yes Yes —