CONTENTS OPERATIONS ® 8000 000> INTRODUCTION UNPACKING . 1 A WORD ON INSTALLATION .. 2 CAUTIONS 2 PAPER TYPES AND SIZES 3 PART NAMES AND FUNCTIONS . 5 OPERATION PANEL i sanitarians 7 . SETTING UP INSTALLING THE SUPPLIES . . @ Installing the Taller Cleaner and the Toner Collecting Container .. .. 9 installing the Photo conductor Cambridge Installing the Developer Cartridge Installing the Toner Cartridge INSTALLING THE EXPANSION MEMORY (OPTIONAL) . .. CONNECTING THE INTERFACE CABLE. .
PROGRAMMING HEX DUMP MODE .. it LINES PER PAGE PRINTING WIDTH .o et RESETTING THE LASER PRINTER Panel Default Settings Factory Default Settings ® FONTS o . GENERAL INFORMATION ® MISDEED REMOVAL it @ SUPPLIES REQUIRED .. Toner Kit Required Developer Cartridge Required. . .. Superconductor Cartridge Required Paar Required SERVICE REQUIRED USER MAINTENANCE . PRINTOUT FUNCTION . PRINTER TROUBLE? EFFUSE Lo e User Troubleshooting . . SHIPPING INSTRUCTIONS SPECIFICATIONS .. .. ..otter ® OPTIONS AND SUPPLIES .. ..
CAUTIONS N INSTALLATION Improper installation may damage the Laser Printer. Please note the following during initial installation and whenever the Laser Printer has been moved. Be sure o use the rated collage from a properly grounded wall outlet only. Do not install the Laser Printer in areas that are: damp or humid, exposed to direct sunlight, extremely dusty or smoky, poorly ventilated, subject 10 extreme temperature or humidity changes, e.g.
HEILONGJIANG PAPER TYPES AND SIZES Standard Papers ® Automatic Feeding from the Paper Cassette Sizes ]‘ B5 Ad Invoice X 182 x 257 mm 210x 297 mm 81127 x 5112 L Letter Legal Executive 8127 x14” 747 < i01/2” Weights oy e gfm® m® 18 los. 21 Ibs. *The A4 size cassette is a standard accessory on the J-8500. Cassettes in other sizes are available as options & Manual Feeding Sizes Same as nautical fessing. Waits 60 gfm? ) 130 gim? 16 lbs. P 341bs L = *Papers with weights from 80 g/m? to 130 g/m? (21 Ibs.
Envelopes & Manual Feeding Sizes J— e bL [international C5 10 %220 mm 162 % 229 mm Commercial\ 10 ™ Monarch ] (Business) = 378 %7127 4187 x Weights gim? 90 gim? 16 Ibs. = 24 lbs. ~Envelopes can be used only with face up output.
L [emerita i R PART NAMES AND FUNCTIONS @ Extension Tray Fold out to receive legal size paper © Face Down Tray Collects the printed paper face down, © Upper Unit Release Button Press to open the Laser Printer. © Operation Panel Contains the indicator lamps, operation keys, and display. © Manual Feed Riot Special papers, envelopes, and paper notion the cassette can be fed through the manual feed slot. © Paper Cassette Holds up 1o 250 sheets of paper.
© Power Switch Press to furn the Laser Printer power on end off. © Face Up Tray Special paper and envelopes fed through the manual feed slat are output here. @ Connector for Optional Second Cassette Unit @ RS-232C Serial Interface @ Electronics Parallel Interface @ Expansion Memory Slot Cover Open the cover to insert optional Expansion Memory. @ Font Card Slots (A, B) Accept optional font cards which provide additional font selection.
L [s Bela i ELUDE OPERATION PANEL The operation panel s used to set the Laser Printer offline for direct operations, such as setting the menu items and executing self-sets Note the following when using the operation anal: ® Set the printer of tine before using the keys. ® Some keys have several functions, which are selected by the duration of time the key is pressed. Be sure to check the functions on the display.
@& CONTINUE/ Used to deject the following two functions: CONTINUE: Clears most errors (ses page 81). Used for the flowing operations: * To set the printer online from the offline state after an error. ® To cancel printer self-tests and set the printer on-line. ® o set the printer on-ling from the menu settling mode. ® 1o continue printing with the current paper source even when the printer requests a different paper size {or envelope type).
2. SETTING UP ® Remove the Laser Printer from the plastic bag. Remove securing tape (A), (B) and (C), and packing material (D). dft ILLINOIS INSTALLING THE SUPPLIES Installing the Roller Cleaner and the Toner Collecting Container 1. Hold the top of the Laser Printer and press the upper unit release Hutton to open it. 2. Remove the roller cleaner from its plastic bag. 3. Install the roller cleaner on top of the fusing unit.
4. Firmly Insert the toner collecting container to the position of the snow. Installing the Photo conductor Cartridge 1. Remove the photo conductor cartridge from is plastic bag. BE CAREFUL NOT TO TOUCH THE PHOTO CONDUCTIVE DRUM. 2. With the photo conductive drum facing down, Tull insert the superconductor cartridge into the Laser Printer, sliding it along the guides. 3.
CLONE ) Installing the Developer Cartridge . Remove the developer cartridge from iis pals damage . 2. Remove the protective plastic cover. 3. Shake the developer cartridge vigorously in a horizontal direction four or five times. ; bag, taking care not to 4. Place the developer cartridge cn & revel surface, hold it in place, and remove the covering material. ® Be careful not to touch the developer roller. ® Do not remove the sealing plate on the other side of the developer cartridge.
5. Press the levers on the developer cartridge with both hands and slide it into the Laser Printer along the guides.
Bl e ) Installing the Toner Cartridge 1. Shake the toner cartridge horizontally four or five times 2. Align the toner cartridge slots with the developer cartridge hooks, and rotate until it clicks and is securely attached. 3. Hold the wren cartridge and pull out the sealing tape from the toner cartridge. With the upper unit in a fully upright position, tap on the toner cartridge four or five times to release all the goner into the developer cartridge. 4.
INSTALLING THE ERA & TENSION MEMORY (OPTIONAL) The expansion memory is available as an option (see page 86). 1. Turn off the power. 2. Remove the expansion memory cover on the hottie handled side of the Laser Printer by pulling the cover tab fo the right and out. 3. Insert the expansion memory, with the arrow facing up, all the way into the Laser Printer. 4, Replace the expansion memory cover. # {f the cover cannot be replaced, the expansion memory may be improperly inserted {upside down).
dft VANILLAS CONNECTING THE INTERFACE CABLE The laser Printer is equipped with both a Electronics parallel and a RS-232C serial interface. The Laser Printer has been set at the factory to use the Electronics parallel interface. To sef the RS-232C serial interface, see SETTING THE MENU [REMS, page 42. NOTE: A shielded, grounded cable and connector are required to comply with either FCC Class B or VDE 0871 and 0875 requirements. 1. Turn off the power 2. Remove the protective cover from the desired connector.
LOADING PAPER The paper cassette feeds paper for automatic feeding and can hold about 250 shews of standard weight paper (80 to 80 g/m?2 weight). ® When using ihe paper casserole for e first time, be sure to remove the securing tape shown below before loading the paper (Follow the same procedure when using the optional cassettes.) 1. Push the pressure plate until it locks in position. Tap EOR TR 2. Fan up to 250 she's of standard paper. 3.
LR UEN k] PRINTER SELF-TESTS Amer you have performed il the installation procedures for the Laser Printer, we recommend that the self tests be performed to check printing. There are two self tests: SELF TEST #1 and SELF TEST #2. SELF TEST #1 prints the selected menu stems and values. SELF TEST #2 prints an entire sheet of characters in a test pattern using the internal character set. To perform these tests, check that the: ® supplies are installed.
SELF-TEST #1 1. Press anc hold the PRINT FONTS/TEST key unit the display shows "“SELF TEST #1" [ coma FEED A SELF TEST J|rest | B ® The DATA lamp lights and printing begins. & The printed sheet listing the menu settings (a.g. type of interface, emulation, elect, such as shown below, is output, and the DATA lamp turns ofl. ® \When printing is complete, “TRAY" appears on the display.
2 L BRUNT 174 M3 ANON] ,you are now ready fo print o pure files. To print Comptrollers check that the: @ supplies are installed. ® paper cassette is loaded with paper. (Be sure the paper size matches the size of the document to be printed.) ® computer is connected through the proper interface cable. # Laser Printer is connected ‘o a power outlet. the power switch 1o turn on the power WARMING UP” appears on the display.
LTS MANUAL FEED PRINTING The manual feed sot allows manual feeding of paper other than standard 60 1o 8O g/m? paper. such as heavier paper stock, transparency film, and envelopes. When using nonstandard paper, select the Ace up tray. Face Up Tray The race up fray holds up lo 30 sheets of paper. I'he face up tray is lactated on the back of the Lager Printer. When using, fold down and out as shown below. *Note that the tray might not be able to hold legal size paper.
Continuous Manual Feed Printing ¢ When manual feeding envelopes, use tha face up tray. 1. If the Laser Printer is online, press the LINE key to set the printer offline. ® The ON LINE lamp turns off and “TRAY" (ie. A4 size cassette installed) appears on the display. 2. Press the A or V key several times until "MANUAL FEED” appears on the display. 3. Press the ENTER/RESET MENU key. ® The MANUAL lamp lights. ® An asterisk appears on the display.
Press the ENTER/RESET MENU key. An asterisk appears on the display. Press the MENU key several times unit! “MANUAL FEED " appears on the display. 8. Press and hold the CONTINUE/RESET key until “RESET” appears on the display. ® "READY [LJ2IMF" appears on the display, and the ON LINE lamp lights. e 7 EERIER E ARG PR PICNIC LESS T NE " |[Fgam | {mev FEED RESET 9. Send data from the computer t the Laser Printer.
Laser Printer menu items such as paper orientation, interface selection, emulation mode, and jot can be set using the operation panel keys. These have bean per-selected at the factory 1o 1he initial settings given below, which will remain in effect until changed. When the settings have been changed to sail your printing needs, they can be saved as Panel Default Settings, which are used whenever you turn on the printer or reset it.
Diabolic 630 Emulation Functions Font source Resident Fern number c Character pits 0 MENU SETTING MODES There are two kinds of menu: the Printing Menu and the Configuration Menu, The Printing Menu contains items that determine the final appearance of the printed page such as the font and Ines per page. The Configuration Menu contain items that determine the communication rethought between the computer and the Laser Printer, The items in each menu differ depending on the emulation mode.
NG PROCEDURE Press the LINE key fo set the Laser Printer off-one. 2. Press the MENU key to select either the Printing Menu or Configuration Menu. Printing Menu: “COPIES=01%" appears on the display. CI READY TN EON LNE D Data e |[Foae R FEES A | COPIES=01 * CHE errs v Configuration Menu: appears on the display. T i e Example: . ‘ HP Laser let f e MERE A series || | * emulation mgsEr_HTest 3. Press the MENU key again urinal the desired menu elem appears on the display.
fim -] Press the ENTER/RESET MENU Key. ® An asterisk () appears on the display. READY CRUCIAL NE LT DATA FONT NUMBER=06 Press the MENU key until the display whose “TRAY" TRAY = A4 * ENTER sy g 7 the display to save the setting. 7. Press and hold the CONTINUE/RESET key until “RESET" appears on ® “READY [LJ2]T" appears on the display, and the ON LINE lamp lights. ® Tne selected value becomes available as a Anal Default Settling.
‘ HP LASER ET Printing Menu stems The Printing Menu for the HP Laser let series It emulation includes the following items: Number of copies Sets the number of copes for the moot-print feature. Manual feed paper size Sets the paper size in the manual feed made. This em appears only when the manual feed mode s set. Envelope size Sets the envelops size. This item appears only when the optional envelope bleeder is installed.
Printing Menu Reference Guide fem Display Electable values Number of copies C1, 02, .
Number of Copley The number of copies is a prows-on default, and will return to “COPIES=01" when the power Is turned on. 1. Press the LINE key to set the Laser Printer off-line. 2. Press the MENU key once so that "COPIES= 01 * " appears on the display. CI READ AN Ci Om COPIES=01 Press the A or V key to select the desired number of copies from 1 to 99, Press the ENTER/RESET MENU key. An asterisk () appears on the display. PN LI READY. MANUAL IO LINE |[EoEM VEND COPIES (PR, Forts eager || rest T 5.
Manual Feed Paper Sis e—— e 1. Set the Laser Printer o the manual feed mode (see page 21). 2. Press the LINE key to set the Laser Printer €. 3 Press the MENU key once sc that "“COPIES= 01 % appears on the display. 4. Press the MENU key again until “MANUAL" appears on the display. REEDY ALMANAC SON ENDS OAT URE | [Fam e MANIA Continue | BRI, [PERTER NS } e hvd EN 8 Press the A or V key fo select the desired paper size: LETTER... Letter Commercial 10 (Business) Legal MONARCH .. Monarch EXECUTE. Executive DL..
Envelope Ste This selling is made when Ihe optional envelope feeder i installed. 1. Press the LINE key to set the Laser Printer offline. 2. Crass the MENU key once so that "COPIES=01% " appears on the display. 3. Press the MENU key again until " appears on the display. S — [ET— g L DORY [ED] i A [ENVELOPE:COM-W i 4. Press the & or V key to select the desired envelope size: COM-1 Commercial 10 (Business) MONARCH Monarch Dl International DL Cs .. International C& 5. Press the ENTER/RESET MENU key.
Auto Tray Change This smelting is made when the optional second cassette unit is installed. Press the LINE key fo set the Laser Printer off-line. 2. Press the MENU key once so that “COPIES=01 " appears on the display. 3. Press the MENU key again until "AUTO TRAY CHG=N*" appears un the display. AUTO TRAY CHG =N * 4. Press the A or ¥ key to deject the desired mode: Y {YES) or N (NO), & Press the ENTER/RESET MENU key. ® An asterisk appears on the display.
Font Source 1. Press the LINE key to set the Laser Printer off-one 2. If using an optional font card, insert it in the font card slot. See page 60, 3. Press the MENU key orc so that appears on the display. 4. Press the MENU key again until "FONT appears on the display. Ornery CI MANUAL [ | 1 CINE ;ERE-EA MENU sewer Press the A or ¥ key to select the desired font source: [ (Internal), A (slot A), B (slot B), S (soft font).
Font NUMERATE s 1. Press the LINE key 1o set the Laser Printer offline. 2. Press the MENU key once so that “COPIES= 01" appears on the display. 3. Press the MENU key again until "FONT NUMBER=00* " appears on the display. = FONT NUMBER=00 4. Pressie 4 or V key to select the desired font number {see font list, pages refer to the font printout sample). 5. Press the ENTER/RESET MENU key. & An asterisk (k) appears on the display. . Tetanus. _ CINE ELUCIDATE FONT NUMBER=08 WE |(Fem FEES = jul HARRELL 6.
HP Laser Jet Series Il Internal Font Number List TYPEFACE POINT { PITCH = SYMBOL SET | PORTLAND o0 Curler 12 10 ROMAN-8 PORT 01 Courier 12 10 IBM-US PORT 02 | Courier 12 10 PORT 03 | Courier 12 10 ACME-94 PORT 04 | Courier Bold 12 10 ROMAN-8 PORT | 05 | Courier Bold 12 10 1BM-US PORT { 06 | Courier Bold 12 10 (BM-D/N PORT | 07 | Courier Bold ECZEMA PORT l 08 Line Printer 85 187 § ROMAN-8 PORT | 09 Line Printer 85 167 | IBM-US PORT | 0| tine Printer 85 | 167 | BM FORT | oy 11| Line Printer 85 | 167 | ECMASCR
Form Length 1. Press the LINE key to sat the Laser Printer off-one, 2. Press the MENU key acne so that "COPIES= 01 % appears on the display. 8. Press the MENU key again until "FORM LENGTH=064%" appears on the display. 4. Press the A or V key to select the desired lines per page from 5 o 128, 5. Press the ENTER/RESET MENU key, ® An asterisk () appears on the display. SRz o atom, FORM LENGTH=078 [Foists iv4 Press the MENU key once 20 that the display shows "TRAMWAY. 7.
| Configuration Menu stems The Configuration Menu for the HP Laser Jet series 1l emulation includes the ‘ following items: Symbol Set A symbol set is & sub-grouping of the characters available In a font. Interface Electronics parallel and RS-232C seal interfaces are available. The printer is preset at the factory for parallel communication Timing With the Electronics parallel interface, the timing for i receiving the acknowledge signal differs depend‘ ing on the computer.
Configuration Menu Reference Guide stem Display Electable values Symbol! set SYM.
Symbol Set Press the LINE key to set the Laser Printer offline. 2. Press and hold the MENU key for longer than 5 seconds until ™ appears on the display. CI READY TI MANUAL ION REPLETION FH ‘ LIE FORM ‘ [ERL SYMLSET=ROMAN® reservist VEIL: 3. Press the & or V key to select the desired symbol set. ! 4, Press the ENTER/RESET MENU key. ® An asterisk () appears on the display. canoeing Evacuate NECTARINE Fez M-din *J RN Nits Test FHL ILLINOIS 5. Press the MENU key until the display shows “TRAMWAY. ‘ 6.
INHERITANCE st sss——— 1. Press the LINE key to set the Laser Printer off-line, 2. Pres sand hold the MENU key until “SYMMETRY ROMAN-8% " appears o the cosplay, 3. Press the MENU key again until %" appears on the display. [k Civilian EM:M, A i PARALLEL asset 4 Press the A or V key to select the desired interface mode: SERIAL or PARALLEL. ® The Configuration Menu items differ depending on the interface mode. Follow the respective procedure below. (PARALLEL interface) 5. Press the ENTER/RESET MENU key.
{SERIAL interface) 5, Press the ENTER/RESET MENU key. ® An asterisk appears on the display. CESAREAN ANTIHERO QN HELL TATS [ i serial * fF = SERIAL zeroes. e e 6. Press the MENU key once 1o display “BAUD RATE=2600% " 7. Press the A or V key 1o select the desired sifting and press the ENTER/RESET MENU key. ® An asterisk appears on the display. R R Cov [ESTER Press the MENU key once to display “"ROBUST OXONIAN* " 9. Press the A or V key fc select ON or OFF and press the ENTER/RESET MENU key.
Emulation — — he LINE key to set the Laser Printer off-line. 2. nd hold the MENU key unit “SYMMETRY ROMAN-8 % " appears an the display. 3. Press the MENU key again unit “EMULATION= HFLJ2 %" appears on the display. SON LNE DDA ] o FIE | EMULSIFICATION * 4. Press the A or ¥ key lo select the desired emulation: HPLJ2 {HP Laser Jet series i} FX80 {Epson F-80) IBM (IBM Graphics Printer) fi‘fi IBM (IBM Pro printer) gx 0630 (Dialog 630/630 ECS) B HEX {Hex Dump) 5. Press the ENTER/RESET MENU key.
MENU SETTING STRUCTURE HP Laser Jet series Il Configuration Menu Printing Menu Press and hold & sec Symbol set Number of copies Interlace Manual feed paper size l | 1= parallel i Only in manual =serial feed mode. ‘ Serialize y Bret : ‘ Baud rate terr Envelope size Only with ok ™ envelope deafer. E‘E‘ Ra bust XON To next item Auto tray change stirring Only with second m R S— cassette unit. OTR polarity Font source Font number ‘ Emulation L Form length ; Lo Menu items Press the MENU key to select menu items.
OTHER EMULATIONS For the Epson F-80, [BM Pro printer. IBM Graphics Printer, and Diabolic 630/630 ECS emulations, the menu settling structure, setting tiers, and delectable values differ depending on the emulation The keys used o select menu items and values and the setting procedure are the same as those used for HP Laser Jet series |} emulation. See page 26 for the Basic Setting Procedure.
Fixed Select (F-80 only} This is effective only when the parallel interface is selected. When on, SELL IN {pin 36 on the parallel interface connector) is ignored and the printer is always in the select mode.
MENU SETTING STRUCTURE Epson F-80 I -LINE ready stage . Configuration Menu OFF-LINE ready state Printing Menu " |Press and hold 5 sec, g National character { Number of cub 1 ; Interface Manual feed paper size Only in manual Parallels! ] feed mode. ; To next — ' TIMING item Envelope size Only with r%fi Serialize envelope feeder Eg ; Baud Rate | [ Auto feed Auto tray change Only with second L ! cassette unit.
MENU SETTING STRUCTURE IBM Electroencephalographic Printer Configuration Menu OFF-LINE ready siesta [ Printing Menu Press and hold 5 sec. National character Interface Served {parallel Baud rate TIMING Robust XON DTR polarity i To next fem Granulation j e | BUMPPO | &) Ever » Auto line feed Auto carriage return* Zero character” *IBM Pro printer only. item | Number of copies Manual feed paper size i Only in manual o next feed mode. Envelope size Only with envelope feeder.
Diabolic 630/630 ECS Emulation Printing Menu stems tem Printer Display Electable Value Number of copies COPIES=01 Manual feed paper MANUAL LETTER, LEGAL, size EXECUTE, INVOICE, Ad, B5, COM-10, MONARCH, DL, C5 Envelope size COM-10, MONARCH, DL, C§ Auto tray change AUTO TRAY CHG=N | N (NO}, Y (YES) Orientation ORIENTATION=P P (Portrait) L {Landscape) Font source FONT SOURCE=| { {internal fort) A (slot A) B (slot B) FH1 VANILLAS Font number FONT NUMBER=00 International Font 00 (COURIER) Font Card (Options) Dia
MENU SETTING STRUCTURE Diabolic 630/630 ECS Configuration Menu OFF-LINE ready state Crass and hold & sac, ‘ =] Printing Menu National character Number of copes | Interface | paper size o Only in mania Serialize To next feed made. Baud Rate fem ! Envelope size 20 Only with ] — envelope feeder, ] y TIMING gz Robust XON | Auto tray change F TONE EE’. Only with second I cassette unit., next item = DTR polarity Orientation Emulation Font source 4 .
This feature {used minty by programmers) prints the hexadecimal equivalent {ASCII code) of the incoming data. An example of a hex dump printout is shown below. HEX CODE MESSAGE SENT BEEs111TREL66PEE 10m(8UR(splohl2v OR OAR ViR 78H shakiness HERE] ZHEJIANG] Hooters here 1 2HO BEKIHFFGEk 2HRMEK 12HFELKIHTTREK2H SIGHTREAD/ 2HERSKL2H/Makl Procedure (Example using HP Laser Jet series Il emulation) 1. Press the LINE key to set the Laser Printer offline. 2.
LINES PER PAGE The lines per page will always default 1o the number given below when the printer is turned on. Norma! Size ORIENTATION PORTRAIT EMULATION LR 1= PAPER SIZE* \LE|LL [EX| N | A4 [B5|CM|MO|C5|DL HP Laser Jet series T 6 LPl 80|78 157 45|64 |54 |51 |30 48|45 Epson F-80 6 LPt 83|81 IBM Pro Printer .
Extended Size ORIENTATION PORTRAIT EMULATION P PAPER SIZE™ |LE | LL [EX|IN | A4 |B5 |CMIMO|C5 | DL Epson F-80 6 LPI 66 |84 | 6351170 IBM Pro Printer » BM Graphics Printer 8 LPI 88 (112,84 | 6893 /80|76 |60 72|68 Diabolic 830/830 ECS 12 LPI 140 120 | 114 | 90 | 108|102 Extended Size | ORIENTATION LANDSCAPE i EMULATION LPI* ! PAPER SIZE™ [LE | LL |EX|IN | A4 |B5 |CM|MO|C5 | DL : Epson F-80 6 LPI 49|42 2423|3825 IBM Pro Printer IBM Graphics Printer 8 LPt 68|68 3230|5134 Diabolic 630/630 ECS 12 LPI 102102186 14
PRINTING WIDTH In the portrait mode, the printing width for each paper size is as shown below. In emulations other than HP Sandblaster series |I, the maximum printing width on A4 size paper is 2,400 dots, allowing 80 characters to be printed on one lire at 10 opi. NOTE When printing 80 characteristic on Ad size paper, in some cases characters may print beyond the paper edge. Avoid printing 80 characteristic on Ad size paper and reduce the number of characters per fine.
& TYING THE [ The Laser Printer can be reset to the panel default settings or its factory default seedlings with the procedure below. Pane! Default Settings Mary software packages send printer commands which will override the panel default settings. Reset e printer at the start of each job to ensure that the panel default settings are in effect. o Press the LINE key to set the Laser Printer offline. . Pres and hold the CONTINUE/RESET key until “RESET” appears on the display.
Factory Default Settings dilemma Os fault Se tings Number of copies 1 OO0 O0f0 Auto tray change OFF Ol 0|C Font source Internal o Q Font number 0 olojoj0o|C Form length See table below.
Three types of fonts can be used with the J-8500 Laser Printer: resident fonts, card fonts, and downloadable fonts (soft fission. 3 Resident Fonts Font Card The fonts that can be used in each emulation mode are given below.
5. GENERAL INFORMATION MISDEED REMOVAL The Laser Printer stops when & misdeed occurs. The display will show “PAPER JAM". After removing the missed paper and clearing the paper jam error, the page that jammed will be reprinted. In some cases, two pages which were in the Laser Printer mechanism at the time of the paper jam (the one being printed and the other ona being ejected) are reprinted.
® |f no paper is fount: Check the paper cassette for missed paper. Open the face up tray and lift the paper guide to check for missed paper. 3. Close the Laser Printer, press the CONTINUE/RESET key. & The ON LINE lamp lights. "READY [LJ2]T" appears cn the display, and when "READY" stops blinking, preening can continue. R HEED) Read Y (2] T I CAUTIONS ® if the paper is torn while it is being removed, be sure 1o remove all pieces.
SUPPLIES REQUIRED Toner Kit Required When the display shows “REP. TONER KIT”, the toner cartridge should be replaced. At the same time, the toner collecting container and the roller cleaner must also be replaced. The toner cartridge replacement kit includes a goner cartridge, toner collecting container, and roller cleaner. 7. Press the upper unit release button o open the Laser Printer 2. Remove the used roller cleaner from the top of the fusing unit CAUTION The fusing unit is hot.
5. Lift up the green lock plate on the top side of the toner cartridge and rotate and pull out to detach it from the developer cartridge. 8. Shake lhe new toner cartridge horizontally four or five mes fo loosen the toner. 7. Absinthe tenet cartridge slots with the developer cartridge hooks and rotate unfit i clicks and is securely attached.
Developer Cartridge Required Her the display shows "REP. DEVELOPER", the developer cartridge should be replaced. Note that the teens finer collecting cocaine, and roller clearer must also be replaces i. Press the upper unit release button to open the Laser Printer. 2. Press the green levers an the developer cartridge with both hands and pul out the toner and developer cartridges together 3. Remove the new developer cartridge from: the plastic bag.
7. Press the green levers on the developer cartridge with booth hands and slide it into the Laser Printer along the guides. 9. Install the new toner «it. ® For installation procedure, see page 63. 10, Close the Laser Printer.
VIAND Photo conductor Cartridge Required When the display shows “REP, PHOTO. DRUM®, the photo conductor cartridge and ozone filter should be replaced. 1. Press the upper unit release button to pane the Laser Printer 2. Press the green levers on the developer cartridge with both hands and pul out the toner and developer cartridges together. guides.
5. Remove the new ozone tighter from the top of the packing material, remove from the plastic bag, and insert it into the Laser Printer. Turn the green sleeper back info pace. 8. Remove the new photo conductor cartridge from the plastic bag With the superconductor drum facing down, fully insert the photojournalist cartridge, sliding it along the guides, VANADIUM Hood the nonconductor cartridge and pull the green tab to remove the protective sheet.
8 Reinstall the developer and toner cartridge 9. Close the Laser Printer Paper Required When the display shows “PAPER OUT TRAY, pull out the paper cassette in use. I it is empty, load pager in the cassettes (see LOADING PAPER, page 6).
JEERED SERVICE When the flowing messages appear on the display, service by an authorized Sharp Service Technician is required. Contact your service center as soon as ‘ possible.
USER MAINTENANCE The maintenance procedures that are to be performed by the user are given below. Cleaning the Cabinet When the Laser Printer cabinet becomes dirty or stained, wipe with a soft, clean cloth. If necessary, dampen the cloth with warier Do not use thinner, benzene, or similar volatile cleaning agents. Cleaning the Corona Wires If the printouts are blotchy or streaky, dirty corona wires may be the cause. Transfer corona charger 1.
PRINTOUT UNCTION There are three printout functions: test printout, menu setting list, and font list. Executing the Printout Function 1. Press the power switch to tum on the power ® “WARMING UP” appears on the display. @ The ON LINE lamp lights, the READY lamp lights, and "READY [LJ2]T" appears on the display. In about 80 seconds, "READY” stops blinking. 2. Press the LINE key to set the printer outline. ® The ON LINE lamp turns off. 3, Press the PRINT FONTS/TEST key fo select the desired printout function.
SAMPLE FONT FONT SYMBOL Ho. NAME ID___SET PRINT SAMPLE s INTERNAL FO: NI SCARCE (1) €6 COURIER 110 10,0 12.0 18444 07 CURTER Bold ON 10.0 12.0 12 147 78,y ANTIPOVERTY 08 LINE FAINTER 8U 16.6 B.5 09 LINE PRINTER 100 16.6 Aetdet#a0NT (712 et 10 LINE INFERENCE 11U 16.6 smcdefasal\1 L3792 Bl R ] LINE FAINTER oM 16.% KB NINTHS ({2712 : 12 COURIER a9 100 COURIER 10U 10.0 12,0 rSM LT @R Mermen COURIER 11U 10,0 12.0 COURIER O 10,0 12.0 MDT Bold BU 10.0 12.0 Bold 100 100 12.0 €DOT O HMR COURIER Bold 110 10,0 12.
Menu Setting List (SELF-TEST #1) This function prints cut the settings of the Printing Menu, Configuration Menu and other settings. It also prints out the remaining life of the supplies and printer A sample printout of the menu settings is shown below.
PRINTER TROUBLE? Errors When any of the following error messages appears on the display, remedy the error condition following the procedure below. Error Message Description Remedy INPUT BUFFER FULL The host computer ignores the printer's busy state and continues to send data. Check the protocol signal line between the printer and the host computer or adjust the setting. Press the CONTINUE/ RESET key.
Error Message Ascription Remedy REP. End cf developer car| Replace the developer DEVELOPER trudge life. cartridge. See SUPPLIES REQUIRED, page 65 REP. PHOTO. £nd of photocopier Replace the superconductor DRUM for cartridge fife. cartridge. See SUPPLIES REQUIRED, page 67. REP. TONER Sorer cartridge is Replace with a new inner KIT almost employ. it See SUPPLIES REQUIRED, page 63 REP. TONER Toner collecting laconically the goner collecting COLL. trainer is not installed | container property. properly.
User Troubleshooting Before calling for service, try the remedies given below. Laser Printer does not turn on ® laser Printer plugged ir? Plug the Laser Printer into a grounded outlet ® Power switch on? Turn the power switch on. Laser Printer turns on but does not print data from computer ® s Laser Printer bonding? Press the LINE key. ® s interface cable connected property? Connect the Interface cable.
R e 1 INSTRUCTIONS Follow the procedure below whenever transporting or shipping the Lases Printer 1. Press the upper unit release button to open the Laser Printer. 2. Remove the toner, developer, and photo conductor cartridges and the toner collecting container. NOTE: Any tire the photo conductor cartridge is removed from the printer, it must be placed in a bag which does not allow the photo conductor cartridge 10 he exposed to light.
AVOIDANT SPECIFICATIONS Printer Print process Page orientation Print speed Paper size Envelope size Print area Dot resolution Paper deaf Cassettes Cassette capacity Manual feed Delivery tray Photocopier Developing stern Fusing system Print color Replacement toner Warm-up time Interface Emulation Resident font Optional fort Power source Power consumption Dimensions Weight Noise level Operational conditions Desktop type Diode laser, dry elector-photographic method Portrait {upright) or landscape (horizontal)
Qr D SURPLICES Options JX-955U JX-BSEF JX950C JX-95RC JX95AC JXO5A J-0585 JX95GC JHGEMT IX-MEME JXGEMH JX9CA JOCASTA JX-9C4M JUDICIAL JX-GC3A Supplies JXG5DR Second cassette unit (250 sheets) (not including cassette) Envelope feeder {40 sheets max.) Legal cassette (250 sheets) Letter cassette (250 sheets) Invoice cassette (250 sheets) A4 cassette (250 sheets) BS cassette (250 sheets) verity cassette (250 sheets) IR} B) memory (1 Expansion memory (2.
Oxidation APPENDIX INTERFACE HARDWARE The Laser Printer is equipped with two interfaces: 1) Electronics parallel 2y R8-232C serial This section provides information on the type of connector, pin configuration, pin signals and signal timing charts. ELECTRONICS PARALLEL Connector Female 36-pin DDK B7LE-40360-730B (D29} or equivalent, Pin Configuration The pin numbers and signal names are given in the table below.
Signal Descriptions Pin 1 (STB, printer Input): Low when data tc be sent to the pinier is valid, Pins 2-9 (DATA 1 to DATA & printer input): TGN purse 0 yogis ™ i Pin 10 (KNACK, pinier output: Low pulse acknowledges data received and processed, computer can send next data. Pin 11 (BUSY, printer output): High signal when printer is busy and cannot receive data, low signal when printer is ready to receive dale. Pin 12 {PE, printer output): High signal indicates paper out.
Rf-232C Connector Female 25-pin DDK 17LE-13250-28 (DECK) or equivalent. COCCOCO0OOO0O0 Pin Configuration The pin numbers and signal names are given in the table below. PIN SIGNAL NAME SOURCE 1 FG {Frame Ground) 2 TXD (Transmitted Data) PRINTER 3 RXD (Received Data) HOST 4 BTS (Re guest to Send) PRINTER 6 DSR (Data Set Ready) HOST 7 GND (Signal Ground) 20 DTR (Data Terminal Ready) PRINTER Signal Descriptions Pin 2 (TXD, printer output): Data from the printer to computer.
Oxidation RESIDENT FONTS The Resident Fonts built into the JX-95C0 are different in each of the emulation. See the list below and the character set printouts on the following pages.
HP Laser let series 1l Line Printer 8.5 point 16.
Oxidation Epson F-80 Courier Script 6 point 10 ¢pi CAPITALISTIC LOWER 4 BT UPPER 4 BIT 1 2 4| 5|67 9 koala rovlz!l nom 107 £ National Character
Xiongnu Epson F-80 Condense 12 point 17.6 cpi CAPITALISTIC UPPER 4 3IT .9 A) B CHD.
UBA FRANCE GERMANY ENGLAND DENMARK 1 SWEDEN ITALY SPAIN JAPAN NORWAY DENMARK Pos ot [ [ ion 8 iyt National Character Table 114 Xiongnu
T7E USA FRANCE GERMANY ENGLAND DENMARK SWEDEN ITALY SPAIN JAPAN #0052 NORWAY T DENMARK National Character Table 18 Dignify
iBM Pro printer Condense Script 6 point 17.6 cpi USASCIH+IBM CHR.
Xiongnu IBM Graphics Printer Courier 12 point 10 cpi CHR. UPPER 4 BIT 1 2 3[4 81678 9. A[B|C E|F roller E|a|g|t]t ale= 'tV 1|A|Q .
Xiongnu IBM Graphics Printer Condense 12 point 17.6 cpi USASCII+IBM CHR, UPPER 4 BIT 1 fe2di3i a5 9.
IBM Graphics Printer Condense Script 6 point 17.6 cpi USASCII+IBM CHR.
R ERL ] Diabolic 630/630 ECS Courier 12 point 10 cpi SCHUSS LOWER 4 BIT UPPER 4 BIT ol 3 |l National Character usA FRANCE GERMANY EM GLAND DENMARK Swede N ALy # 085 FAN JAPAN NORWAY & i @ Uoé =2 ¢ & DENMARK 127
INDEX A o Accessories L1 Acknowledge signal aiming 8, 41, 89 Auto feed. . 45 Automatic ¢ 49, 52 Automatic line feed .47, 49, 52 Auto tray Baud raise Button, upper unit 5 C Cabinet, cleaning Carriage retire, autocratic Cartridge developer photo conductor toner Caution Concentric parallel interface Character pitch. Cleaning cabinet .o 71 main .7 transfer corona charger. .71 Clearing horrors, paper jams Code bit. Condense . Condense script.
[INDEX Expansion memory installation Extended size printing 45 Extension tray e D F Face down tray 5 Face up 6, 21 Factory default settings FC MISMATCH message Fixed Font Source 34 FORM FEED key. 8 Fern length 37 Fusing unit 6 H Hax dump. HP Laser sines I 1BM Graphics Printer.. IBM Inappropriate Initial settings INPUT BUFFER FUL Installation developer cartridge expansion memory superconductor cartridge roller cleaner toner cartridge toner collecting container.
INDEX £ MENU .8 Menu setting | 18, 79 Menu setting structure HP Laser series | 44 Epson F-80 48 IBM Pro printer 50 IBM Graphics Printer 50 Diabolic €30/630 ECS National character Number of copies 0 Operation panel ON LINE lamp Options Orientation Ozone fitter . p Packing Page orientation Page Panel default settings . Paris, operation Paper cassette jam loading manual fee orientation type.. weight .. PAPER JAM message. PAPER OUT Photo conductor cartridge . B8 installation. . 10 replacement ..
INDEX panel default settings Robust XON Roller cleaner, installation. replacement REP. DEVELOPER message. REP. PHOTO. DRUM message REP. TONER COLL. message REP. TONER KIT message RS-232C serial interface S Second cassette unit Set-tests SELF TEST #1. SELF TEST #2. Serial interface Service messages . Setting menu items Settings factory default panel default. Signal timing chart.
EMULATION INFORMATION HP Laser let series il Central Codes. . it Escape Sequences Job Control . Line and Page Control 137 Cursor Comfort. 141 Character and Font Control 144 Graphics Control. Macro Control Other Control Printer Command Table Epson F-80 IBM Pro printer .. . . IBM Graphics Printer .
EMULATION INFORMATION HP Laser Jet series i o allow the programmer to use HP Laser Jet series Il emulation with their JX-850C Laser Printer, the following information on emulation commands is required. Control Codes Control Codes are commands to tell the printer how to process the data it receives.
Escape Sequences Job Control SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE! FUNCTION: This is & programmable command to tell the printer how to process data, it consists of a decimal or hexadecimal ESC control code followed by a specified character. Please refer 1o the reference material provided with your computer or software. Select special features of the printer: ESC z {Interface lest-test) Instructs the printer o perform an interface self test.
Line and Page Control SEQUENCE: FUNCTION: SEQUENCE: FUNCTION The escape sequences control page orientation, page length, margins, ine deaf, perforation skip, ste. ESC &f#H Selects the paper handling method for the printer. Can be received inserted in the page, remains effective until anther pager handling command is received by the printer or a paper handling command is changed oy key input.
SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: ESC &r#P (Spicily page length) Specifies the physics! length of the paper being used as the number of lines Portrait or landscape orientation does not affect the specification. !f the orientation is changed, specify the page length first.
SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: ESC &f#F (Specify text length) Specifies the number of lines of text 1o he printed on a page. If a text length value of O is specified, the text length is defaulted 12 inch from the bosom of the page.
SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: ESC &i#C (Set vertical motion index) Sets the vertical line spacing of printed text in 1/48th inch increments. The value range for 336 and can be specified to four decimal places. The table below shows examples of VMI values: This command affects ihe lne feed and half line feed spacing.
Cursor Control SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: Control cursor positioning for the printer: ESC &a#C (Horizontal cursor control — columns) For horizontal positioning of the cursor in increments of the current column pitch (characters per inch) within the print omits of the page. Column values exceeding the print limits of the page will position the cursor at the left or right limits of the current page.
SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: ESC *p#Y (Vertical cursor control — dots) For vertical positioning of the cursor in increments of dots (200 dpi) within the print limits of the page. before the dot value moves the cursor relative to the current cursor position (+ doer; — up). A dot value without positions the cursor relative to the top margin (# = 0). The previous table (ESC *p#X) shows examples of dot values.
SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: ESC 8k#G (Print line termination) Selects the printer’s interpretation of the computer's line termination character, The table below shows the print line termination selection values: Computer Printer Va lug ‘termination interpretation 0 (default) GCR Carriage Return , Ling feed = Form feed ESC &f#3 (Pushiness position) Allows the cursor position {o be saved (pushed) and retailed (pooped) at any Up to 26 curse positions can be stored at one time with the last cursor i
SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: 18O 2: International Reference Version Escape U EM-1 ESCAPE U PC-8 ESCUDO PC-8 (DIN} ESC) 11 U Pi Fort ESC) 15 U ESC {(s#P (Select primary font character spacing) Selects proportional (# = 1) or fixed (# = 0) character spacing for the primary forty.
SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQ FUNCTION: SEQUENCE: FUNCTION: ESC (s#V {Select primary font point size) Selects the font size (character height) o print the primary character font. The table below shows examples of point values: The factory default height is 12 points. One paint is 1/72 inch. Value Point size 144 144 ESC Jeeves (Select secondary font point size) Selects the font size (character height) 1o print the secondary character font.
SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: if the specified stroke weight is greater than or equal 1o G and is not available, the next thicker available stroke weight will be selected. If no thicker stroke weight is available, the closest available thinner stroke weight will be selected. If the specified stroke weight is less than zero and is not available, the text thinner available stroke weight will be selected.
SEQUENCE: FUNCTION SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION; SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: ESC 8&k#8 (Select font pitch) Selects either standard pis (10 characters per inch) or compressed pith (1666 characters per inch) to print both primary and secondary character finis.
SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: ESC ¢c#F (Character and font control) Specifies the characterization control function to be performed on the font last specified by the ESC *a# D (Specify font ID) escape sequence. # species the control function.
SEQUENCE: FUNCTION: ESC Jewess [DATA] (Download font description) Creates a font header which describes the characteristics of the font last specified by the font ID. The field value specifies the number of byes in the font descriptor data field. if a font with the same font 1D exists, the previous font will be deleted from printer memory when the new valid download font escape sequence is received.
Baseline distance: Data bytes 6 and 7 specify the distance from the top of the character cell o the baseline in dots. The value is the same for portrait or landscape orientation; see the following figure. The baseline must be contained within the character cell. Therefore the value of the baseline distance fails between 0 and the cell height minus 1 i Underpins seine Dt o Ponderer b Mo ] The character cell {Portrait orientation) Cell width: Data bytes 8 and 9 spicily the width of the character cell in dots.
Symbol sei: Data bytes 14 and 15 select the symbol sef to be used for the rew fol. The number to select the symbol set is calculated by multiplying the number in the symbol set field value by 32, adding to it the decimal ASS! value of the letter, and then subtracting 64 from the total. Symbol set field value = ROMAN 8x32 + (ASCII value for 256 277 = Symbol set bye value The following table lists the symbolism sets, their field values and byte values.
Pitch: Data bytes 16 and 17 specify the pith {coi) of the font characters. The pitch value is calculated by dividing the horizontal resolution of the printer (300 dots per inch) by the desired pitch. The pitch is specified in increments of 1/4 (.25) of a dot and the pitch value can range from 0 to 16800, A value exceeding 18800 will be set to 16800, Height: Data bytes 18 and 18 specify the height of the font characters. The height value is calculated by multiplying the desired height (in dots) by 4.
Typeface: Daley byte 25 specifies the typeface of the fonts.
SEQUENCE: FUNCTION: Pitch extended: specifies Pitch Extended value. on o the Pitch field which extends the pitch an extra eight bits. The value of this field is in 1024th of one dot For example, a 17 pitch font would have & Pitch field of 70 (17.5 dots, or 17.1429 ¢pi) and a Pitch Extended field of 150 (01465 dots additional, which gives 176465 dots, ar 170005 clip.
Fort Species the formal of the character descriptor and date. The format number used by the JX-B500 is 4. Continuation: Specifies whether the following data is a character descriptor block (0) or a continuation of the data associated with the previous character descriptor. Because cape sequence value field is limited to 32767, characters whose nurturer of descriptor and data block bytes would exceed this limit must be downloaded in two or more blocks.
Left offset: Data bytes € and 7 specify the distance from the reference point 1o the left side of the character pattern in dots.
SEQUENCE: FUNCTION: Graphics Control SEQUENCE: FUNCTION SEQUENCE: FUNCTION: Delta X: Data bytes 14 and 15 are used to specify the horizontal (X) distance the curse will trace! after printing a specified proportionally spaced character. Delta X is specified as the desired numbered of dots multiplied by 4. For example, if the desired character spacing is 5 dots, the deft X value would 20). The range of delft 18800, Character data: Data byes from 16 are the raw data used to represent the character.
SEQUENCE: FUNCTION: SEQUENCE: FUNCTION; SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: ESC *b#W [DATA] (Transfer raster graphics) Specifies the number of binary graphics data bytes o be sent to the printer for processing. The bytes of data are translated to bits of raster graphics data and sent to the printer one fine (dot row) at a time. ESC *b#W must be sent to the printer for each line of graphics data.
SEQUENCE: FUNCTION: SEQUENCE: FUNCTION SEQUENCE FUNCTION: ESC “c#V (Vertical rectangle counterpoints) Specifies the length of a vertical rectangle in checkpoints (720/inch). Power on or reset defaults the vertical rectangle size to 0. Values greater tha page size are accepted, but are printed within the printable area boundaries.
Macro Control SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: These escape sequences contra the creation and use of macros, A macro is an escape sequence which combines other escape sequences (o perform a task. The macro can be stored and then recalled to perform the same task again, the printer can store up to 32 macros &t a time, ESC &f#Y (Specify macro 1D} Assigns an iD Number 1o a sacra.
Current environment escape sequences Page length Primary font address Page orientation Font [0 Input control Character code Copy count Macro ID Margins Vii fine spacing Top Horizontal rule spacing Left Vertical rule size Right Underline mode Perforation skip Graphics resolution Line termination Graphics mode EOL {wrap) termination Graphics left margin Font attributes Pattern 1D HMI ESC &I3X, call mast, ex the macro identified by the macro 1D in the current environment.
10 E8C &5X, disable auto macro overlay, exits the auto macro overlay function at the current page. Changing the page length or orientation disables the auto macro overlay alder ESC &5X is executed. EEC &6X delete all macros (temporary, permanent and auto macro overlays) that may have been in effect. ESC &f7X delete all temporary macros (including auto macro overlays) that may have been in effect.
Other Control SEQUENCE: FUNCTION: SEQUENCE: FUNCTION: SEQUENCE: FUNCTION SEQUENCE: FUNCTION: ESC Y (Select display functions mode} Disables all control codes and escape sequences and allows them to be printed as blanks (spaces) with two exceptions: carriage return (CR) is executed as a carriage return (CR) + Sine feed {LF), and ESC Z is executed and printed as a blank fallowed by a Z.
Printer Command Table FUNCTION [~ SEQUENCE [ COMMAND | PAGE JOB CONTROL Interface self-test ESC z 136 Printer reset ESC E 136 Number of copes ESC &f#X 138 LINE and PAGE CONTROL, Paper handing Eject page ESC &0H 137 Paper cassette ESC &e1H 137 Manual feed ESC &2H 137 Envelope manual feed ESC H 137 Second cassette unit ESC &taH 137 Envelope feeder ESC &e6H 137 PAGE LENGTH and SIZE Page size Executive ESC A 137 Letter ESC &R2A 137 Legal ESC &e3A 137 A4 ESC &f28A 137 Man arch ESC &f Boa 137 Commercial 10
Printer Command Table {cont) FUNCTION | SEQUENCE COMMAND | PAGE CURSOR CONTROL HORIZONTAL and VERTICAL Horizontal Calumny ESC Anzac 141 Dots ESC *p#X 141 Descriptors ESC fax H 142 Vertical Lines ESC &a#R 141 Dots ESC *p#Y 142 Checkpoints ESC &a#V 142 Hall line feed ESC = 142 LINE TERMINATION Print line termination CR=CR LF=LF ESC &Kong 143 ESC &gawk 143 ESC &k2G 143 ESC &k3G 143 PUSH/POP POSITION Push/pop position Push ESC 4108 143 Pap ESC &l8 143 CHARACTER and FONT CONTROL SYMBOL SET SELECTION Primary font
Printer Command Table (cont) FUNCTION SEQUENCE COMMAND | PAGE Spanish ESC (1S 44 1S0 17: Spanish ESC (28 144 1S0 10: Swedish ESC (35 144 150 16: Portuguese ESG (45 4 1S0 84: Portuguese ESC (55 144 180 85: Spanish ESC (65 144 150 6: AS CHI ESC (U 144 Legal ESC (1U 144 1SO 2; international Reference Version ESC (2U 145 SCHMOES (7U 145 PGB ESC (10U 145 PC-8 (DIN) ESC (11U 145 Pi Font ESC (15U 145 Secondary font symbol set ESC )# # 144 SPACING Primary font character Proportional ESC (1P 145 spacing Fixed ESC (s
Printer Command Table {(cont) FUNCTION SEQUENCE COMMAND =~ PAGE Stripe ESC (7T 147 Prestige ESC (s8T 147 Gallon ESC {s9T 147 Orator ESC {01st 147 Presentations ESC (11T 147 Optima ESC (17T 147 Gar among ESC (s187 47 Cooper Black ESC (81st 147 Coronet Bold ESC (s20T 147 Broadway ESC (8217 147 Aver Dodson Black Condensed ESC (5227 147 Gentry School back ESC (s23T 147 University Roman ESC (s24T7 47 Secondary font typeface £5C )s 2T 147 FONT PITCH Primary & secondary Font pitch 10.
Printer Command Table (cont) FUNCTION | SEQUENCE [ COMMAND | PAGE RECTANGLE DIMENSIONS Rectangle width Number of dots ESC ‘c#A 159 (Horizontal size) Number of checkpoints ESC ez H 159 Rectangle height Number of dots ESC "c#B 159 {Vertical size) Number of checkpoints ESC ‘caV 160 RECTANGULAR AREA FILL Print paternoster Black rule ESC 0P 180 Gray scale pattern ESC “c2P 180 Defined pastern ESG *¢3P 160 Defined painter Horizontal line ESC *c16 160 Vertical lens ESC *c2G 160 +4§ deg. lines ESC *¢3G 180 45 deg.
Epson F-80 The commands available in Epson F-80 emulation are listed below. Epson F-80 Command Codes FUNCTION COMMAND REMARKS Bell BEL Backspaces BS Cancel CAN Horizontal Tab HT The maxim urn TAB position is subject to current paper width. Line Feed LF Vertical Tab VT If a securest is made for a cola son outside the printer's logical page, the current page is ejected. Carriage Return CR Page End FF Condensed Moe ON st Characters are printed at 17.1 CPI {137 characters on one cinch ling).
Epson F-80 Command Codes {cont} UNCTION COMMAND REMARKS Paper Out Detection ESC 9 This command is ignored. Enable Print Mode Select ESC ! () {0=n=568) Underline Print Mode ESC ~ {n) n=1, 49 ON OFFEND {minus) n=0, 48 CFF VFU Channel Select ESC /7 {1} 0=n=7) Home Head (Printing from | ESC < This command is ignored since deft mast to right for 1 ling) it has no print head mechanism. MSB 0 Set ESC = MSB 1 Set ESC > MSB Control Sequence ESC # Cancel Printer Initialize ESC @ Print buffer is cleared.
Epson FX-8¢ Command Codes (cont}) FUNCTION COMMAND REMARKS Control Code Select ESC ¢ Undefined codes in the range 00H to IFH and 804 to 9FH are assigned as character code. n=0, 48 Control code n=1, 48 Printable character N2167 Line Feed ESC J () 0=n=255 8-pin Normal Density Bit ESC K {m} Prints about 1/5 page without Image Expansion memory. 8-pin Dual Varsity Bit ESC L (n} Same as above. Image Elite Size Mode ES CM 12 CPI Perforation Line Skip ON ESC N (g This command is ignored.
Epson F-80 Command Codes (cont) FUNCTION COMMAND REMARKS Left Margin Set ESC 1 {n) n: depends on print mode. if & request is made for & spice died position outside the printer's logical page, he position s pacified © the appropriate logical page limit. P/8 Character Print ESC ¢ () ON OFFEND n=C, 43 OFF Half-Sped ON ESC s (n} This command is ignored since print head speed is irrelevant. 8-pin Bit Image Mode ESC ~ (n) Prints about /5 gaps without expansion memory.
M Pro printer The printer commands are given in the table below. The ESC 6 code allows access 1o IBM Pro printer Character Set 2. The ESC 7 code returns back to IBM Pro printer Character Set 1. IBM Pro printer Command Codes FUNCTION COMMAND REMARKS Cancel CAN Condenser mode OFF DC2 10 CPI Enlarged OFF C4 Condensed rode ON sl 17.1 CP1 (137 characters on che gins ling). Enlarged ON 30 Carriage Return CR Printer Select oct Printer Ceaseless DC3 Page End FE Vertical Tab VT Line Feed L.
1BM Pro printer Command Codes (cont) FUNCTION COMMAND REMARKS Print Continuously from Al | E8C N(n) | (1=n=2585) Characters Chart Print Single Character from | ESC A (n} Ali Characters Chart n{72* LF Pitch Set ESC A (n) (1=n=8E) Vertical Tab Set ESC B (n) Max. 84 positions, Page Length Set in Lines ESG G () Form length=Line spacing xn 8 1.
IBM Pro printer Command Codes (cont) FUNCTION COMMAND REMARKS Cancer! Skip Perforation. ESC O This command is ignored. Deselect IBM Pro printer ESC G 3 Set All Tabs 10 Power On ESC R Settings Super/Subscript Moe ON | ESC 5 (1) 48 Superscript n=1, 49 Subscript Super/Subscript Mode OFF | ESC T Unidirectional Printing ESC U () This command ‘s ignored.
IBM Graphics Printer The printer commands are given in the table below. The ESC 6 code allows access to lBM Graphics Printer Character Set 2. The ESC 7 code returns back 10 IBM Graphics Printer Char ctr Set 1 IBM Graphic Printer Command Codes FUNCTION COMMAND REMARKS Cancer! CAN Clears the printer buffer. Control codes, except SO remain in effect.
IBM Graphic Printer Command Codes (cont) FUNCTION COMMAND REMARKS Horizontal Tab Set ESC D (n) {1=n=80) normal meed (t=n=132) compressed made. When the pacified TAR postilion crosses the current paper width, the data is ignored. The maximum tab umber is 256, Emphasized CN ESC E Double printing at 2/3007 paging.
Diabolic 630/630 ECS The printer commands available in this emulation are given in the table below. Diabolic 630 Command Codes FUNCTION EMBARKS Bell BELL Backspace B3 Carthage Return CR Delete DEL This command is ignored. Supplementary Character EM Access for one character sees Select sen when in 7-hit ECS mode. Page End FF Horizontal Tab HT Line Feed LF Ult NIL Shift In St £C8 mode blanks the character at BCH-OFH. 7-kit ECS mode selects pri harbormaster set.
Diabolic 630 Command Codes (cont) FUNCTION COMMAND REMARKS Auto Backward Print OFF ESCAPE Same as above. Auto CYRIL ON ESC? Auto CYRIL OFF ESC! Reverse Print ON ESC « Reverse Print OFF ESC » Backward Print ESC 8 Cleared by CR. Forward Print ESC 5 Vertical Movement Index YMI Set ESC RS () x 1 (0=n=128) Mace to Vertical Absolute Position ESC VT (g Nol returnable 1o preceding page due to cut heel.
Diabolic 630 Command Codes (cont) FUNCTION COMMAND REMARKS Auto Justify 3o M Auto Censer ESC = Precised by CR. 1120 Backspace ESC 89 Program Mode Select ESC SO M This command Is ignored, Ward Processor Mode ESC X Cancel Envelope Fed ON SCHEME Tray 1 Feed ON ESC EM 1 Tray 2 Feed ON ESC EM 2 Page End Assignation ESC EM R | Causes same operation as F¥ code. Printer Initialize ESC SUB | | Power-Cr initialization, Remote Error Reset ESC SUB R Status Boyle 1 Request ESC SUB 1 | In RS-232C I/F mode only.
