User`s manual
Table Of Contents
- Safety Precautions
- Table of contents
- Chapter 1: Outline
- 1-1 Features
- 1-2 Controller
- 1-3 Measurement program
- [1] Positional deviation measurement
- [2] Degree of match inspection
- [3] Lead inspection
- [4] BGA/CSP inspection (IV-S32M/S33M)
- [5] Area measurement by binary conversion
- [6] Object counting by binary conversion
- [7] Object identification by binary conversion
- [8] Point measurements
- [9] Distance and angle measurement
- [10] Multiple position measurement (IV-S33M)
- [11] Multiple degree of match inspection (IV-S33M)
- Chapter 2 : Precautions for Use
- Chapter 3 : System Configuration
- Chapter 4 : Part Names and Functions
- Chapter 5 : Connection and Installation Methods
- Chapter 6 : Setting and Operating Outlines
- Chapter 7 : Simplified Menu Operation
- 7-1 Operation screen
- 7-2 Image display
- 7-3 Setting functions that are different with each controller
- 7-4 Setting procedures
- 7-5 Setting the operation conditions
- 7-6 Setting object types
- 7-7 Setting the shutter speed
- 7-8 Setting the positioning conditions
- 7-9 Setting the existence inspection conditions
- 7-10 Measurement triggering
- 7-11 Saving data
- 7-12 Specify the system conditions
- Chapter 8 : Specifications
- Chapter 9 : Operation Examples
- Glossary
- Appendix
- Alphabetical Index
7-15
Simplified Menu Operation
7
5. Press the SEL key to change the screen to the freeze mode.
- The indicator in the upper right corner of the screen will change from T to F.
- To register reference images, you must make sure to display the freeze screen.
6. Press the ESC key to display all of the measurement condition items.
- If the menu overlaps the object to be measured, so that further image condition setting is
difficult, press the ESC key. Only one item will be displayed at a time. (You can move the
cursor to each item and display each of them in order on the screen, using the up and down
keys. The following illustration shows only one item being displayed.)
7. Move the cursor to the "2 REF. IMG ARE (MDL 0)" item, and press the SET key.
8. Surround the object to be measured with the image window (solid line).
- Move the cursor to the "MOVE," "UP.L," or "LO. R," label and press the SET key.
After the window position has been finalized, press the SET key.
CONTRAST SEARCH is only
displayed on the IV-S33M
F.IMG C1 L
OPS-MENU
1REG NO 1P-SCH 2P-SCH
2REF IMG ARE(MDL0) MOVE UP.L(224,208) LO.R(287,281) CONTRAST SR
REG DISP
3SEARCH ARE(MDL0) MOVE
UP.L(216,200) LO.R(295,279)
4REF IMG ARE(MDL1) MOVE UP.L(224,208) LO.R(287,281) CONTRAST SR
REG DISP
5SEARCH ARE(MDL1) MOVE
UP.L(216,200) LO.R(295,279)
Display when "2P-SHC" (2-point
search) is selected
Object 1
Search window
Image window
2
REF IMG ARE(MDL0) MOVE
UP.L(110,218) LO.R(174,277) REG DISP
OPS-MENU
F.IMG C1 L
MOVE The whole rectangle is moved using the up, down, left or right keys (one pixel at a time).
UP.L The upper left corner is moved using the up, down, left or right keys (one pixel at a time).
LO.R The lower right corner is moved using the up, down, left or right keys (one pixel at a time).