User`s manual
Table Of Contents
- Safety Precautions
- Table of contents
- Chapter 1: Outline
- 1-1 Features
- 1-2 Controller
- 1-3 Measurement program
- [1] Positional deviation measurement
- [2] Degree of match inspection
- [3] Lead inspection
- [4] BGA/CSP inspection (IV-S32M/S33M)
- [5] Area measurement by binary conversion
- [6] Object counting by binary conversion
- [7] Object identification by binary conversion
- [8] Point measurements
- [9] Distance and angle measurement
- [10] Multiple position measurement (IV-S33M)
- [11] Multiple degree of match inspection (IV-S33M)
- Chapter 2 : Precautions for Use
- Chapter 3 : System Configuration
- Chapter 4 : Part Names and Functions
- Chapter 5 : Connection and Installation Methods
- Chapter 6 : Setting and Operating Outlines
- Chapter 7 : Simplified Menu Operation
- 7-1 Operation screen
- 7-2 Image display
- 7-3 Setting functions that are different with each controller
- 7-4 Setting procedures
- 7-5 Setting the operation conditions
- 7-6 Setting object types
- 7-7 Setting the shutter speed
- 7-8 Setting the positioning conditions
- 7-9 Setting the existence inspection conditions
- 7-10 Measurement triggering
- 7-11 Saving data
- 7-12 Specify the system conditions
- Chapter 8 : Specifications
- Chapter 9 : Operation Examples
- Glossary
- Appendix
- Alphabetical Index
4-1
Part Names and Functions
4
Chapter 4: Part Names and Functions
This section describes the names and functions of the controller, camera (camera lens, camera converter,
camera body and camera cable), and the remote keypad which comprise the IV-S30 system. See section in
Chapter 5 "Connection and Installation Methods" for details about the housing brackets, camera angle bracket
and conversion connector.
4-1 Controller (IV-S31M/S32M/S33M)
S＊.＊＊
42
IV-S3＊M
OUTPUT
INPUT
POWER
Y7Y0 Y1 Y2 Y3 Y4 Y5 Y6
COM
COM
＋24V
X7X0 X1 X2 X3 X4 X5 X6
READY
0V
VIDEO
CAMERA1
CAMERA2
USB
RS232C/RS422
REMOTE
2 Power terminal block
9 Frame ground terminal
4 Monitor connector (VIDEO)
8 Remote key pad connector
(REMOTE)
7 Communication connector
(RS232C/RS422)
Controller (front)
Controller (side)
1 I/O terminal block
3 Power lamp (POWER)
5 Camera 1 connector (CAMERA1)
6 Camera 2 connector (CAMERA2)
mark
(software version ＊.＊＊)
0 Communication connector (USB)
Frame ground terminal
9
Be sure to ground the housing frame ground terminal together with
the frame ground of the constant-voltage power supply in accor-
dance with class 3 grounding procedures. -See page 5-15.
I/O terminal block
INPUT: X0 to X7, C
(+)
OUTPUT: Y0 to Y7,
READY, C
(-)
Name
This block has 8 input terminals and 9 output terminals.
- External devices are connected to these terminals for input and
output (parallel I/F). - See page 5-17.
1
Power terminal block
(＋24V, 0V)
2
Power lamp (POWER)
3
Monitor connector
(VIDEO)
4
Camera 1 connector
(CAMERA1)
5
Camera 2 connector
(CAMERA2)
6
Remote key pad connector
(REMOTE)
8
Commercially available constant-voltage power supply (24 V DC ±
10%, 500 mA or more) is connected here. - See page 5-15.
When the power is applied to the controller, the green lamp will light.
A monitor is connected here.
- The monitor connector is an RCA jack.
The camera cable connector is connected here.
- The camera connected to the CAMERA 1 position is camera 1,
and the camera connected to the CAMERA 2 position is camera 2.
This connector is used to connect a personal computer for communi-
cations (general purpose serial I/F) or to connect a programmable
controller for a computer link. - See page 5-20
The remote key pad connector is used to make selections from the
menues on the screen (to set parameters). It is connected here.
Function
7
0
Communication connector
(USB)
This connector is used to connect a cable to a USB port on a person-
al computer.
- The USB port only functions with Windows 98.
Communication connector
(RS232C/RS422: 9-pin, D-
sub,female, rock screw