User`s manual
Table Of Contents
- Safety Precautions
- Table of contents
- Chapter 1: Outline
- 1-1 Features
- 1-2 Controller
- 1-3 Measurement program
- [1] Positional deviation measurement
- [2] Degree of match inspection
- [3] Lead inspection
- [4] BGA/CSP inspection (IV-S32M/S33M)
- [5] Area measurement by binary conversion
- [6] Object counting by binary conversion
- [7] Object identification by binary conversion
- [8] Point measurements
- [9] Distance and angle measurement
- [10] Multiple position measurement (IV-S33M)
- [11] Multiple degree of match inspection (IV-S33M)
- Chapter 2 : Precautions for Use
- Chapter 3 : System Configuration
- Chapter 4 : Part Names and Functions
- Chapter 5 : Connection and Installation Methods
- Chapter 6 : Setting and Operating Outlines
- Chapter 7 : Simplified Menu Operation
- 7-1 Operation screen
- 7-2 Image display
- 7-3 Setting functions that are different with each controller
- 7-4 Setting procedures
- 7-5 Setting the operation conditions
- 7-6 Setting object types
- 7-7 Setting the shutter speed
- 7-8 Setting the positioning conditions
- 7-9 Setting the existence inspection conditions
- 7-10 Measurement triggering
- 7-11 Saving data
- 7-12 Specify the system conditions
- Chapter 8 : Specifications
- Chapter 9 : Operation Examples
- Glossary
- Appendix
- Alphabetical Index
9-15
9
Operation Examples (Standard menu: Positional deviation measurement)
[2] Positional deviation measurement
The following sections cover an example of how to measure the positional deviation of the positioning
mark shown below.
1
1
1
2
[SELECT MENU]
1STANDARD MENU (STD RUN-MENU)
2SIMPLIFIED MENU (SEL EASY MENU)
Positioning mark
* Object type number
IV-S33M: 00 to 63
IV-S32M: 00 to 31
IV-S31M: 00 to 15
Circles will be displayed
below object type numbers
that are already registered.
To the next page
(1) Power ON
When power is first turned ON after the machine is deliverd, the [SELECT MENU] screen will
appear.
- When the MAIN OPS MENU used by the simplified menus (positioning) is displayed, the
operations covered in step (2) is not needed.
- If the MAIN OPS MENU used by the standard menus is displayed, please change to the simplified
menus screen. - See page 6-5.
(2) Select menu
1.Move the cursor to the "1STANDARD MENU" item with the up and down keys, and press the
SET key.
- The standard mode [MAIN OPS MENU] screen will appear.
(3) Operation on the MAIN OPS MENU (all the conditions are initialized)
1. Move the cursor to the "MEA-CND" item using the left and right keys, and press the SET key.
- The [TYPE MEAS COND] menu will be displayed.
(4) Registration of an object type number (the object is registered in 00 with the IV-
S33M)
1. Move the cursor to the "1OBJECT TYPE NO." item using the up and down keys, and press
the SET key.
2. Move the cursor to "YES" using the left and right keys, and press the SET key.
- Items 2 to 8 will be displayed.
T.IMG C1 L
VX.X
(TYPE00)
MEAS 0000ms XXXX-XX-XX XX:XX
MEASURE 0 CAM1 NO
CHG-MEA CHG-REG CHG-RST CHG-C1 CHG-C2 CHG-EVAL CUSTOM-MNU
OPS-CND MEA-CND SYS-CND CHG-TYPE NG-IMG-DSP NEXT-NG MANL-MEAS
X0∼7 Y0∼7 READY
[TYPE MEAS COND]
[OBJECT REG.LIST]
①
OBJECT TYPE NO. 00(0~63) NO YES
OPS-MENU SAVE LOCK TITLE FINAL-CALC FINAL-OUTPUT I/O SYSTEM
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
× × × × × × × × × × × × × × × ×
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
× × × × × × × × × × × × × × × ×
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
× × × × × × × × × × × × × × × ×
48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
× × × × × × × × × × × × × × × ×
*