User`s manual
Table Of Contents
- Safety Precautions
- Table of contents
- Chapter 1: Outline
- 1-1 Features
- 1-2 Controller
- 1-3 Measurement program
- [1] Positional deviation measurement
- [2] Degree of match inspection
- [3] Lead inspection
- [4] BGA/CSP inspection (IV-S32M/S33M)
- [5] Area measurement by binary conversion
- [6] Object counting by binary conversion
- [7] Object identification by binary conversion
- [8] Point measurements
- [9] Distance and angle measurement
- [10] Multiple position measurement (IV-S33M)
- [11] Multiple degree of match inspection (IV-S33M)
- Chapter 2 : Precautions for Use
- Chapter 3 : System Configuration
- Chapter 4 : Part Names and Functions
- Chapter 5 : Connection and Installation Methods
- Chapter 6 : Setting and Operating Outlines
- Chapter 7 : Simplified Menu Operation
- 7-1 Operation screen
- 7-2 Image display
- 7-3 Setting functions that are different with each controller
- 7-4 Setting procedures
- 7-5 Setting the operation conditions
- 7-6 Setting object types
- 7-7 Setting the shutter speed
- 7-8 Setting the positioning conditions
- 7-9 Setting the existence inspection conditions
- 7-10 Measurement triggering
- 7-11 Saving data
- 7-12 Specify the system conditions
- Chapter 8 : Specifications
- Chapter 9 : Operation Examples
- Glossary
- Appendix
- Alphabetical Index
9-7
9
Operation Examples (Simplified menu: Existence inspection)
1REGISTER NO. 0(0~7) NO YES
1
F.IMG C1 L
4
1
3
2
3
6
5
OPS-MENU
1REGISTER NO. 0(0~7) NO YES
2MEAS AREA MOVE UP.L(224,208) LO.R(287,271)
3THRESHOLD U.LM255 L.LM100(0~255)
4INVERT B/W NO YES
F.IMG C1 L
OPS-MENU
To the next page
(5) Image adjustment
1. Press the SEL key.
- The image taken by camera 1 will be displayed.
- When the image is so bright that the menu display is difficult to see, press the TRG/BRT key to reduce the
brightness of the image. The indicator in the upper right corner of the screen will change from "H" to "L."
2. To display the image of the object measured clearly, adjust the focus and iris opening of the camera lens
(page 4-1).
3. Press the SEL key to change the screen to the freeze mode.
- The indicator in the upper right corner of the screen will change from T.IMG to F.IMG.
- To set a threshold for a binary area, make sure the IV-S30 is displaying the freeze screen.
(For details about the through and freeze modes, see page 7-4.)
4. Move the cursor to the "1REGISTER NO." item using the up and down keys, and press the SET key.
5. Specify "0" for the registration number using the up and down keys.
6. Move the cursor to "YES" using the left and right keys.
- The measurement area will be displayed in the center of the screen.
7. Press the ESC key to display all of the measurement condition items.
(6) Setting the binary area condition (measurement area)
1. Move the cursor to the "2MEAS AREA" item, and press the SET key.
2. Surround the object to be measured with the measurement area (solid line).
- Move the cursor to the "MOVE," "UP.L," or "LO. R," label and press the SET key.
After the position has been finalized, press the SET key.
- After specifying the position of each measurement area, press the SET key.
- If the menu overlaps the object to be
measured, so that further image condition
setting is difficult, press the ESC key. Only
item 1 will be displayed at a time.
Continued from the previous page
MOVE The whole rectangle is moved using the up, down, left or right keys (one pixel at a time).
UP.L The upper left corner is moved using the up, down, left or right keys (one pixel at a time).
LO.R The lower right corner is moved using the up, down, left or right keys (one pixel at a time).
Press the TRG/BRT key and the
brightness of the screen will change
between L and H.
Indicates that Camera 1 is selected.
Measurement area
Measurement area
Object to be measured
Object to be measured