User`s manual
6-4
Setting and Operating Outlines
6
Item on the menu bar Description Display detail on the screen
MAIN-COND
(main conditions)
Displays the MAIN screen.
CHG-MEA
(Change measurement)
Press the up and down arrow keys to change the display of
the evaluation results for each measurement number.
(Measurement 0 camera 1 -> measurement 0 camera 2 ->
Measurement 1 -> Measurement 2 -> Measurement 3 ->
Measurement 4)
COND-CHG
(Change the
measurement
conditions)
Displays the condition change selection list. Change the
conditions that get displayed by pressing the up and down
arrow keys.
For details about the measurement conditions, see "Chapter
3: Instruction and Hardware" in Function and Operation.
For details about the distance and angle conditions, see page
18-2 in Function and Operation.
For details about the numeric value calculation conditions, see
page 19-6 in Function and Operation.
CHNG-REG
(change registration)
Change the display of the set of stored details between [A00] -
[A07] and [A08] - [A15] using the up and down arrow keys
SCREEN-CHG
(change screen)
Displays the screen change selection list. Select a screen
using the up and down arrow keys.
Note: The OPS-MAIN, JDG-COND-CHG, and PC-MNTR do
not appear on the popup menu unless "YES" is selected
for each corresponding item on "TYPE RUN COND"
menu. Only the currently available screens are listed.
When an NG image is stored, "NG-IMG-DISP" can be
selected, press the SET key and the monitor will change to
the NG image display screen.*
- See page 1-22 in IV-C35M User's Manual, Function and
Operation.
CHG-TYPE
(change the object
type)
Displays the object type selection list.
Select an object type by pressing the up and down keys.
This is enabled when Manual Object Type Change is set to
"YES."
NEXT-NG *
(change the NG image)
List the NG screens that can be selected.
Select a screen using the up and down keys.
CHG-C1
(change the Camera 1
image position)
Moves the image from Camera 1 up and down the screen
using the up and down arrow keys.
Note: This is enabled when "CAM1&2" or "CAM1&NG IMG" is
selected in 1MONITOR OUTPUT on the TYPE RUN
COND menu (operating conditions).
CHG-C2
(change the Camera 2
image position)
Moves the image from Camera 2 up and down the screen
using the up and down arrow keys.
Note: This is enabled when "CAM1&2" or "CAM1&NG IMG" is
selected in 1MONITOR OUTPUT on the TYPE RUN
COND (operation conditions).
MANL-MEAS
(Manual measurement)
Manually move the two crosshair cursors, and measure
distance between these two points, as well as coordinate
distance on X and Y axes.
Note: Unless "MANL-MEAS" is selected on the
"qEXTENSION FUNC" line in the TYPE RUN COND
(operation conditions), this screen cannot be displayed.
SHORTCUT Displays a short cut screen.
Details of each item on the menu bar
SYS-CND
OBJECT TYPE COND
SET WIZARD
EDIT MAIN OPS MENU
OPTION
ENVIRONMENT SETTING
MEMORY CARD
MEASURE0 CAM1 NO
This part changes.
MEA-CND
DST&ANG COND...
NUMERIC CALC
COND-CHG
CHNG-REG
OPS-MAIN
JDG-COND-CHG
PC-MNTR
SCREEN-CHG
CHG-TYPE
(TYPE00)
MEAS
0000ms
MEASURE0 CAM1 NO
This part
changes.
＋
＋
MANL-MEAS
1
CURSOR1-COORD MOVE(224.208)
2
CURSOR2-COORD MOVE(287.271)
DIST-BETW-2PT 089.0
DIST-BETW-X 063.0
DIST-BETW-Y 063.0
【
PLACE
】
1
SHORTCUT1 NO
2
SHORTCUT2 NO
3
SHORTCUT3 NO