Service manual

HT-DD5000/C
– 2 –
SPECIFICATIONS
HT-DD5000/C
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
BEFORE RETURNING THE AUDIO PRODUCT
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the
following safety checks.
1. Inspect all lead dress to make certain that leads are not
pinched or that hardware is not lodged between the chassis
and other metal parts in the audio product.
2. Inspect all protective devices such as insulating materials,
cabinet, terminal board, adjustment and compartment covers
or shields, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakage
current in the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.
* Using two clip leads, connect a 1.5k ohm, 10 watt resistor
paralleled by a 0.15µF capacitor in series with all exposed
metal cabinet parts and a known earth ground, such as conduit
or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher,
sensitivity to measure the AC voltage drop across the resistor
(See diagram).
* Connect the resistor connection to all exposed metal parts
having a return path to the chassis (antenna, metal cabinet,
screw heads, knobs and control shafts, escutcheon, etc.) and
measure the AC voltage drop across the resistor.
IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)
All check must be repeated with the AC line cord plug connection
reversed.
Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp.
AC.) or more is excessive and indicates a potential shock hazard
which must be corrected before returning the audio product to the
owner.
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
TEST PROBE
0.15 µ F
1.5k ohms
10W
VTVM
AC SCALE
General
Type: Home theater receiver
Power source: AC 120 V, 60 Hz
Power consumption: 170 W
Dimenslons: Width; 16-15/16" (430 mm)
Height; 5-15/16" (150 mm)
Depth; 13-11/16" (347 mm)
Weight: 21.6 lbs. (9.8 kg)
Output power: (Front)
40 watts minimum RMS per channel into 8
ohms from 60 Hz to 20 kHz, 0.9 % total
harmonic distortion.
(Center)
RMS; 40 W (0.9 % T.H.D.)
(Surround)
RMS; 40 W/CH (0.9 % T.H.D.)
(Sub woofer)
RMS; 40 W (0.9 % T.H.D.)
Output terminals: Front speakers; 8 ohms
Center speaker; 8 ohms
Surround speakers; 8 ohms
Sub woofer; 8 ohms
Headphones; 16-50 ohms
(recommended; 32 ohms)
Input terminals: DVD, VCR-1, VCR-2, CD/AUX,
MD/TAPE; 500 mV/47 kohms
PHONO; 3.5 mV/47 kohms
Tuner section
Frequency range: FM; 87.5 - 108 MHz
AM; 530 - 1,720 kHz
Front speaker section
Type: 2-way, 6-5/16" (16 cm) woofer,
and 2" (5 cm) tweeter
Maximum Input power: 80 W
Impedance: 8 ohms
Dimensions: Width; 8-5/16" (210 mm)
Height; 13" (330 mm)
Depth; 8-5/8" (218 mm)
Weight: 8.2 lbs. (3.7 kg)/each
Center speaker section
Type: 2-way, 5-1/8" (13 cm) woofer
and 2" (5 cm) tweeter
Maximum Input power: 80 W
Impedance: 8 ohms
Dimensions: Width; 15-3/4" (400 mm)
Height; 6-1/2" (165 mm)
Depth; 6-7/16" (163 mm)
Weight: 6.4 lbs. (2.9 kg)
Surround speaker section
Type: 2-way, 5-1/8" (13 cm) woofer
and 2" (5 cm) tweeter
Maximum Input power: 80 W
Impedance: 8 ohms
Dimensions: Width; 8-5/16" (210 mm)
Height; 6-1/2" (165 mm)
Depth; 6-7/16" (163 mm)
Weight: 3.5 lbs. (1.6 kg)/each
Sub woofer section
Type: 6-5/16" (16 cm) super woofer
Maximum Input power: 80 W
Impedance: 8 ohms
Dimensions: Width; 8-5/16" (210 mm)
Height; 13" (330 mm)
Depth; 13-3/8" (340 mm)
Weight: 11.5 lbs. (5.2 kg)
CP-F5000
CP-C5000
CP-SR5000
CP-SW5000
Specifications for this model are subject to change without
prior notice.