Technical data

ManualsBrandsSharp ManualsAir CleanerFU-800-J

FuG Elektronik GmbH, D-83135 Schechen, Am Eschengrund 11

http://www.fug-elektronik.de, E-Mail: info@fug-elektronik.de

V 0913

Features:

 Compact size and light weight

 Efficiency approx. 90%

 For units from 12.5kV nominal

voltage on, all HV compo-

nents are moulded in

(removable) silicon

 Short-circuit & flashover proof

 Unlimited operation with rated

current in a short-circuit con-

dition

 Unlimited operation with rated

power

 Voltage and current regulation

with automatic sharp transi-

tion, control modes indicated

by LEDs

 Adjustable overvoltage pro-

tection (limitation of set value)

 4½ digit DVM's for voltage

and current for all models

 Voltage and current setting by

means of 10-turn potentiome-

ters with precision scale; the

adjusting knob can be locked

 Indication of set point values

by means of button for switch-

over of the displays

 Set point adjustment possible

with locked output, release of

output voltage by means of

"ON" / "OFF" switch

 Suitable also for inductive and

capacitive loads

 Suitable for photomultipliers

Function:

In principle, the rectified line

voltage drives a square wave

generator of fixed frequency,

whose AC voltage is trans-

formed, rectified and filtered,

producing the output voltage.

For regulation, the square wave

voltage is pulse width modulat-

ed.

A low residual ripple of the

output voltage, together with a

high stability, high regulation

speed and a low stored energy

are all achieved by virtue of the

high switching frequency.

Design:

 ½19" or 19" table-top case

(depending on output voltage

and power).

 19" Rack-adapters for mount-

ing into a 19" rack are availa-

ble as accessory.

Output:

 Output isolation:

The required output polarity

must be stated with the order.

The requested output polarity

will then be available at the

HV connector and the “0V”

terminal will be firmly con-

nected to earth. If required,

the "0V" terminal can be

made floating against earth

up to ± 300V. A polarity re-

versal switch is optionally

available.

 Output terminals:

All output terminals are locat-

ed at the rear side of the unit.

High voltage connectors with

the appropriate dielectric

strength are delivered with the

power supply. For nominal

voltage of 65kV and higher the

HV- plug will be delivered

ready mounted to 3m cable.

Technical Data:

 Mains connection:

Up to 1400W nominal power:

230V ±10% 47Hz to 63Hz

For 2800W and higher:

400V ±10% 47Hz to 63Hz,

three-phase

 Ambient temperature:

0°C to +40°C

The following data applies for

voltage and current regulation,

and refers to the rated value

(unless otherwise stated):

(For explanations please refer to

Definitions and Terms on page

54.)

 Setting range:

from approx. 0,1% to 100%

 Setting resolution:

±1 x 10

-4

 Residual ripple (0 - 10MHz):

<1 x 10

-4

pp + 50mVpp,

typ. 5 x 10

-5

 Recovery time:

Voltage control:

<1ms for load changes from

10% to 100% or from 100% to

10%

Current control:

<10ms for load changes caus-

ing an output change of less

than 10% of the rated voltage

 Setting time at nominal load:

<500ms for changes of the

output voltage from 10% to

90% or 90% to 10%

 Discharge time constant for

output without load:

approx. 2sec. to 10sec., de-

pending on type

 Deviation:

For ±10% mains voltage vari-

ation:

<± 1 x 10

-5

For no load / full load:

<2 x 10

-4

Over 8 hours under constant

conditions:

<±1 x 10

-4

Within the temperature range:

<±1,5 x 10

-4

Possible Options:

 Coarse/fine-potentiometers

(99% / 1%) for more accurate

adjustment of voltage and / or

current

 Analog programming (see

page 44)

 Analog programming, floating

(see page 44)

 Computer interfaces - IEEE

488, RS 232, RS 422, Profi-

bus DP, USB, LAN (more on

request) (see page 46)

 Electronically controlled polar-

ity reversal switch (Up to

35kV remotely controllable

when ordered with a program-

ming or interface, for higher

voltages, please ask us).

Please specify the output

polarity, when ordering with-

out polarity reversal switch.

(see page 48)

 Lower ripple (see page 48)

 Higher stability (see page 48)

 Lower stored energy (see

page 48)

 Power limitation (see page

48)

More options and special solu-

tions on request. Some options

may involve changes to the

description of the unit - espe-

cially concerning the mechani-

cal design.

High voltage power supplies

Series HCP from 3,5 kV to 300 kV / 14 W to 15000 W

Design example HCP 140 - 12500

12500V / 10mA