Service manual

FO-4700U
FO-47UC
2 – 30
SW28 No. 5, No. 6 Ringer volume
Ringer volume:
The calling sound volume of CI signal receiving is set.
SW28 No. 7, No. 8 Reserved
Set to "0".
SW29 No. 1 Reserved
Set to "0".
SW29 No. 2 PC I/F mode
The interface with the personal computer is selected.
SW29 No. 3 ~ No. 8 Reserved
Set to "0".
SW30 No. 1 To register senders
When setting this switch to "1", registering senders is protected.
SW30 No. 2 ~ No. 7 Reserved
Set to "0".
SW30 No. 8 Quick on-line function
It is selected whether auto dial call is activated in the memory input
mode when one document is completely read or when all pages are
completely read.
SW31 No. 1, No. 2 Performance of detail paper cassettes
To set selective modes for detail paper cassettes of the printer.
SW31 No. 3 ~ No. 5 The first priority cassette
To select the first priority cassette.
001: 1st paper feeder (MP-TRAY)
010: 2nd paper feeder
011: 3rd paper feeder
Except the above Setting forbidden (Printing started from the
possible paper feeder)
00: Manual
01: Automatic 1
10: Automatic 2
Except the above
To select detail paper in the first prior-
ity cassette in accordance with setting
by SW31 3-8 and SW32 1-3. If the de-
tail paper in the first priority cassette
runs short, the second priority cassette
will be used.
To automatically select detail paper with
optimum size among the first to third
priority cassettes in accordance with
setting by SW31 3-8 and SW32 1-3.
The optimum paper is selected by every
page. If all the cassettes have the same
size paper, paper will be selected ac-
cording to the cassette priority.
To automatically select detail paper with
optimum size among the first to third
priority cassettes in accordance with
setting by SW31 3-8 and SW32 1-3. At
the start of printing, the optimum pa-
per is adopted only for the first page.
Thereafter the same cassette selected
for the first page will be used from the
second page and after. If all the cas-
settes have the same size paper, pa-
per will be selected according to the
cassette priority.
Setting forbidden (01: the same setting
as in the case of Automatic 1)
SW21 No. 2 ~ No. 4 Reserved
Set to "0".
SW21 No. 5 Reserved
Set to "1".
SW21 No. 6 ~ No. 8 Reserved
Set to "0".
SW22 No. 1, No. 2 DTMF detection time
Used to set detect time of DTMF(Dual Tone Multi Frequency) used in
remote reception (5**).The longer the detection time is, the error detec-
tion is caused by noises.
SW22 No. 3 ~ No. 8 Reserved
Set to "0".
SW23 No. 1 ~ No. 3 Reserved
Set to "0".
SW23 No. 4 ~ No. 6 To set busy tone detect frequency
To select frequency range of signals to be detected as Busy Tone.
SW23 No. 7, No. 8 Reserved
Set to "0".
SW24 No. 1 ~ No. 8 Reserved
Set to "0".
SW25 No. 1 ~ No. 8 Reserved
Set to "0".
SW26 No. 1 ~ No. 8 Reserved
Set to "0".
SW27 No. 1 F.A.S.T (RMS) mode
Used to determine a function of remote maintenance system (F.A.S.T).
SW27 No. 2 Reserved
Set to "0".
SW27 No. 3 Verification STAMP
End stamp:
It is set whether the red round mark is stamped at the bottom margin of
the document of every page in the memory input mode and document
sending mode or not.
SW27 No. 4 Summer time (Day light saving)
The day light saving function ON/OFF is set.
SW27 No. 5, No. 6 Key buzzer volume
Key buzzer volume:
The sound volume of key inputting buzzer and other buzzers is set.
SW27 No. 7, No. 8 Reserved
Set to "0".
SW28 No. 1, No. 2 Speaker volume
Speaker volume:
The sound volume of the speaker in the on-hook mode is set.
SW28 No. 3 Reserved
Set to "1".
SW28 No. 4 Reserved
Set to "0".