Service manual

UX-ICMC
FO-215Oc!hIuK!Mc
SW17 No. 1, No. 2 Speaker volume (3stage~r)
Speaker volume:
The sound volume of the speaker in the on-hook mode is set.
SW17 No. 3, No. 4 Hand-set receiver volume (2stages)
Handset volume:
The volume of sound heard from the receiver is set.
SW17 No. 5, No. 6 Ringer volume (4stages)
Ringer volume:
The calling sound volume of Cl signal receiving is set.
SW17 No. 7, No. 6 Reserved
Set to “0”.
SW16 No. 1 PC l/F mode
PC I/F mode:
The interface with the personal computer is selected.
SW16 No. 2 Auto reception in PC l/F mode
Automatic receiving of I/F mode:
Which receives the call is determined.
SW16 No. 3 Summer time setting
This is used to set YES/NO of automatic clock adjustment for summer
time.
SW16 No. 4 Sender’s phone number setting
Used to make a choice of whether the registered sender’s phone number
can be changed or not. If the switch is set to “l”, new registration of the
sender’s phone number is disabled to prevent accidental wrong input.
SW16 No. 5 Polling key
If this switch is set to 1, the last of Rapid key works as polling key.
SW16 No. 6 Activity report print
This soft switch is used to select : whether or not to print out the activity
report when the memory is full. An activity report can be printed when
the following key entry command is made.
“FUNCTION”, ‘Z”, “#“, “START”
After producing the activity report, all the data in the memory will be
cleared.
When the switch function is set to “0” (no), the data in the memory will
be deleted from the oldest as it reaches the maximum memory capacity.
SW16 No. 7 Total communication hours and pages print
Used to make a choice of whether the total communication time and
pages are recorded in the activity report.
SW16 No. 6 Line density selection
Used to set the transmission mode which is automatically selected when
the Resolution key is not pressed. In the copy mode, however, the fine
mode is automatically selected unless the Resolution key is manually
set to another mode.
SWlQ No. 1, No. 2 Density adjustment (when Fine/STD mode)
This is used for density adjustment in fine/standard mode. Adjust the
density according to that of frequently used original.
Set to “Dark” for darker reading (either in the auto or the dark mode) of
light original. Set to “Light” for lighter reading (either in the auto or the
dark mode) of dark original.
Set to “Dark only in dark mode” for darker reading only in the dark mode.
SW19 No. 3, No. 4 Density adjustment (when Half-tone mode)
This is used for density adjustment in the half tone.
SW19 No. 5 HTF correction in Half-tone mode
In the half tone mode, image area is separated from character area and
processed separately to eliminate unclear character transmission.
This switch is used to change the criteria of judgement of separation.
When “Strong” (=l) is selected, more area is judged as character area,
providing clearer characters.
On the contrary, however, edges of image area may be emphasized.
It is advisable to restrict the use of this function only when clear charac-
ters must be transmitted, and to use the function of ‘Weak” (= 0) for
general cases.
SW19 No. 6 MTF correction in Half-tone mode
This allows selection of MTF correction (dimness correction) in the half
tone mode. When “Strong” (= 1) is selected, the whole image becomes
soft and mild, On the contrary, however, clearness of characters will be
reduced. Normally set to “Strong” (= 1).
SW19 No. 7 Separation of image area in the half tone
This allows selection of MTF correction (dimness correction) in the half
tone mode. When “ND” (= 1) is selected, the whole image becomes soft
and mild, On the contrary, however, clearness of characters will be re-
duced. Normally set to “NO” (= 0).
SW19 No. 6 Removal of notch in the binary mode
The notch signal is removed in the binary mode.
SW20 No. 1, No. 2 Paper se4 size
Set the size of recording paper for reception and list print.
SW20 No. 3- No. 5 Media type
Set the type of recording paper for reception and list print.
SW20 No. 6 , No.7 Print quality when fax printing
Set the printing method for reception and list print.
SW20 No. 6 Reserved
Set to “0”.
SW21 No. 1 - No. 6 Reserved
Set to “0”.
SW21 No. 7 Reserved
Set to “1”.
SW21 No. 6 Reserved
Set to “0”.
SW22 No. 1 Reserved
Set to “0”.
SW22 No. 2 Reserved
Set to “1 ‘I.
SW22 No. 3 Half tone copy resolution
The image resolution conversion rate is set in the copy mode.
0 : 203 DPI X 196 DPI (1.53 times X 1.47 times )
1 : 200 DPI X 200 DPI (1.50 times X 1.50 times )
SW22 No. 4, No. 5 Reserved
Set to “0”.
SW22 No. 6 - No.6 Copy Ratio for B/W copy
Set the magnification when “PRESET’ is selected in copy mode.
SW23 No. 1 - No. 6 Reserved
Set to “0”.
SW23 No. 7 Reserved
Set to “1”.
SW23 No. 6 RoseNed
Set to “0”.
SW24 No. 1 - No. 5 Align cartridge (l-30) for color cartridge
After the color cartridge has been mounted press
“FUNCTION”, “6, ‘k”, ‘k”, ‘k”, “START’
to print Bidirectional Alignment Pattern.
On the printed test page, locate the number under the BidirectionalAlign-
ment pattern that comes closest to forming a perfectly straight line.
SW24 No. 6 Fax prfnting wlth paper from manual feeder
To print the received picture in hand paper feed mode, set ‘1”.
SW24 No. 7 Fax printing with color cartridge
To print the received picture with the color cartridge set “1”.
2-15