Service manual

l Soft switch function description
SW1 No. 1 - No. 4 Recall interval
Choice is made for a recall interval for speed and rapid dial-numbers.
Use a binary number to program this. If set to 0 accidentally, 1 will be
assumed.
SW1 No. 5 - No. 8 Recall times
Choice is made as to how many recall attempts should be made. Use
a binary number to program this.
SW2 No. 1 Dial mode
Switch the type according to the telephone circuit connected to the
facsimile.
1 : PULSE DIAL
0 : TONE DIAL
SW2 No. 2 Reception mode
Auto/manual receiving mode is set.
SW2 No. 3 ECM mode
Used to determine ECM mode function. Refer to the following table.
ECM MMH mode
Yes Yes No
No Yes Yes No No No No No No No No No NO
ECM MH mode
Yes Yes Yes Yes Yes Yes Yes Yes No No No NO NO NO NO NO
MR Mode
Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No
1 MH Mode
1 Yes1 Yes IYes I Yes IYes IYes IYes IYes IYes IYes IYes IYes IYes IYes Yes IYes I
(Depending on remote machine)
SW2 No. 4 CNG detection in Standby mode
When setting to “l”, the CNG signal detection function during standby
stops.
SW2 No. 5 Polling Security
This switch is employed to enable or disable the polling operation using
the ID code verification function, in order to prevent unauthorlzed poll-
ing operation.
SW2 No. 8 Automatic Cover Sheet
When “0” (=YES) is selected, the cover sheet is automatically sent after
transmission of the original to notify the receiver of the number of origi-
nal sheets transmitted.
SW2 No. 7 Junk fax function in manual reception
It is set whether Junk fax is functioned in the manual receiving mode or
not.
SW2 No. 8 Anti Junk fax function
This function is used to receive data from a specific remote machine
(station registered in entry mode). It is the function that refused a recep-
tion in the case that TSI of remote machine mached with fax number of
the station registered.
0 : No
1 : Yes
SW3 No. 1 - No. 4 Number of rings for auto receive
(0 : No ring receive)
When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from one to nine rings
using a binary number. If the soft switch was set to 1, a direct connec-
tion is made to the facsimile. If a facsimile. If it was set to 0 accidentally,
receive ring is set to 1.
SW3 No. 5 - No. 8Automatic switching manual to auto receive mode
(0 : OFF)
Choice is made after how many rings in the manual receive mode it
should be automatically change to auto answer mode or remain in the
manual receive mode. Entering the binary number 0 forces the machine
to remain in the manual answer mode. If a number between 1 and 9 is
entered, the machine will go into the answer mode after the given number
of rings. However, it can be used as an ordinary telephone if the handset
is taken off the hook before this programmed number is finished.
SW4 No. 1 - No. 3 Communication results printout
(Transaction report)
Every communication, the result can be output. As usual, it is set to print
the timer sending communication error alone. If No.1 : 0 No.2 : 0 No.3
: 1 are set, printing is always on (printed ever if it is normally ended).
000 : Error, timer and memory sending/receiving
010 : Sending
110 : Continuous printing
100 : Not printed
001 : Communication error
SW4 No. 4 Delay timer before line connect in auto dial
Delay time between the dial key input and line connection under the
auto dial mode.
RAPID01
CML RELAY ON
k-4 DIALLING
0 : osec
1:3sec
2-12