User Manual
34 EN
Recording
Timer Recording using the SHOWVIEW® system
You can programme the
timer using the SHOWVIEW
programming numbers that are
printed in your local TV guide
magazine.
1
In stop mode, press [TIMER
PROG. SHOWVIEW].
SHOWVIEW Programming window
will appear.
• If you have not set the clock,
the clock setting window will
appear instead. In such case,
continue from step 4 in “Clock
Setting” on page 21 before
programming the timer.
• If the Timer Programming list
is full, the Timer Programming
mode is activated instead of the
SHOWVIEW programming mode.
• Press [TIMER PROG.
SHOWVIEW] again in the
SHOWVIEW programming
mode to switch to the Timer
Programming mode.
2
Set the SHOWVIEW programming
number of the programme
you want to record using [the
Number buttons], then press
[ENTER].
ShowView System
Please enter a ShowView No.
- - - - - - - - -
3
Select the desired recording
pattern using [Cursor K / L],
then press [ENTER].
ShowView System
M-F
Weekly
Once
Daily
Once:
To record a TV programme once,
as you set.
Daily:
To record a TV programme at the
same time on the same channel
everyday.
M-F:
To record a TV programme at the
same time on the same channel
from Monday through Friday.
Weekly:
To record a TV programme at the
same time on the same channel
every week.
4
Select a recording channel using
[Cursor K / L], then press [Cursor B].
• If your local channel
information is programmed
in the unit’s memory, your
local channel number appears
automatically.
• If your local channel
information is not programmed
in the unit’s memory, “P– –”
may appear.
• If you select the channel
number using
[Cursor K / L]
, it is
stored in the unit’s memory.
Timer Programming
2. - - -
3. - - -
4. - - -
1. Daily 7:30 14:15 P01 LP ON
Date Start End CH Mode
VPS
PDC
5
Select the recording mode
using [Cursor K / L], then press
[Cursor
B
]. (See page 23.)
6
Select VPS / PDC to “ON” or
“OFF” using [Cursor K / L], then
press [ENTER]. (See page 31.)
7
Press [SETUP] or [TIMER PROG.
SHOWVIEW] to exit.
8
Press [
OPERATE].
The icon will appear on the
front panel display and the unit
enters to the timer-standby
mode.
ZOOM
DISPLAY
SETUP
TOP MENU
MENU/LIST
REC MODE
REC/OTR
PAUSESKIP SKIP
PLAY
CM SKIP
AUDIO
OPEN/CLOSE
FWD
REV
CLEAR
1
2
3
4
5
6
7
8
9
SPACE
0
A
HG
ENTER
PROG.
RETURN
.@/:
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
B
C
{
B
K
L
h
g
F
STOP
RAPID PLAY
TIMER
PROG
.
SHOW VIEW
OPERATE
2
1
2
3
4
5
7
8
6
Note
• If the SHOWVIEW programming number is not available, “Code Error!”
is displayed and the number will clear when you press [ENTER] in
step 2.
• If the SHOWVIEW programming number previously set overlaps
with the one you entered and the channel is different, “Overlap”
is displayed but the timer programming will be cleared when you
press [ENTER] in step 3.
• If you enter the same SHOWVIEW programming number and the
recording pattern which you have already entered, the previously
set programme will be overwritten.
• If you enter the same SHOWVIEW programming number but a
different recording pattern, it will be saved as a new programme
and added to the timer programming list.
• If you want to monitor the programme that you are recording,
make sure the device such as Set-top Box is turned off when it is
connected to AV2.
“Code Error!” is displayed if:
• A past time is entered for start and end times.
• The SHOWVIEW programming number cannot be decoded.