User Manual
29EN
Recording Disc Playback EditingBefore you start Connections Getting started
Changing the
Setup menu Others
Recording
ZOOM
DISPLAY
SETUP
TOP MENU
MENU/LIST
REC MODE
REC/OTR
PAUSESKIP SKIP
PLAY
CM SKIP
AUDIO
OPEN/CLOSE
FWD
REV
CLEAR
1
2
3
4
5
6
7
8
9
SPACE
0
A
HG
ENTER
PROG.
RETURN
.@/:
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
B
C
{
B
K
L
h
g
F
STOP
RAPID PLAY
TIMER
PROG
.
SHOW VIEW
OPERATE
Basic recording / One-touch Timer Recording (OTR)
This operation may take a
few moments to complete.
Note
• You can change the channel while in the REC pause mode when basic recording.
• You cannot change the recording mode while in the REC or REC pause mode.
• If the clock is not set, the date and time space next to title names in the Original or Playlist will be blank.
• The unit will be turned off automatically under the following conditions.
- No space remains on the disc. - If a power failure occurs.
• If you want to monitor the programme that you are recording, make sure the device such as Set-top Box
is turned off when it is connected to AV2.
• Even if the broadcasting you are recording is in the SECAM system, this unit automatically converts it to
the PAL system when recording.
5
6
7
8
4
2
1
Follow the steps below to record
a TV programme.
1
Press [
OPERATE] to turn on
the unit.
Turn on the TV and be sure to
select the input to which the unit
is connected.
2
Press [OPEN/CLOSE A] to open
the disc tray.
3
Place the disc on the disc tray
with its label facing up. Be sure
to align the disc with the disc
tray guide.
Disc
tray
guide
4
Press [OPEN/CLOSE A] to close
the disc tray.
5
Select the recording mode
using [REC MODE].
(See page 23.)
SP 0:58
6
Select the desired channel to
record using [PROG. K / L] or
[the Number buttons].
P08
7
Press [REC/OTR] to start record-
ing.
The “I” mark will be displayed
for 5 seconds.
I
To pause the recording, press
[PAUSE F]. Press [PAUSE F] or
[REC/OTR] again to restart the
recording.
8
Press [STOP C] to stop the
recording.
To set the One-touch Timer Recording (OTR)
This is a simple way to set the recording time in blocks of 30 minutes.
At step 7, press [REC/OTR] repeatedly until the desired recording time
(30 minutes to 8 hours) appears on the TV screen.
One-touch Timer Recording will start.
• To change the recording length during one-touch timer recording,
press [REC/OTR] repeatedly until the desired length appears.
• To cancel One-touch Timer Recording within the specified time, press
[STOP C].
• The remaining recording time will be displayed on the front panel display
during One-touch Timer Recording. Press [DISPLAY] to see it on the TV screen.
• Unlike the timer recording, you can perform the following operations during One-touch Timer Recording.
- Turning off the power. - Using [REC/OTR] or [STOP C].
• You cannot use the pause function during One-touch Timer Recording.
• When One-touch Timer Recording is finished and the power is turned off, the unit will switch to the timer-
standby mode automatically if a timer recording has been programmed. Press [
OPERATE] to cancel the
timer-standby mode to use the unit continuously.
0:30
(Normal Recording)
8:00 7:30
1:00
I
0:30