User Manual

32 EN
Recording
Timer Recording (cont’d)
1 2 3
6
54
7
0
8 9
AUDIOREPEAT
PAU S E
SEARCH
SLOW
MENU LISTTOP MENU
STOP
PLAY
FWD
REV
SKIP
PROG.
CLEAR/C-RESET
VCR
REC/OTR
DVD
REC/OTR
PQRS TUV WXYZ
GHI JKL MNO
.@/: ABC DEF
SPACE DISPLAY
ENTER
ZOOM
REC MODE
VCR
RAPID PLAY
DVD
CM SKIP
SETUP
T-S ET
OPEN/CLOSE
EJECT
TIMER PROG.
SHOW VIEW
DUBBING
RETURN
OPERATE
In the following example, No.
5 timer programming overlaps
on No. 1 and No. 6 timer
programmes. In such a case, you
should correct the programme
time to clear the overlap.
Timer Programming
2. - - -
3. - - -
4. - - -
7. - - -
8. - - -
Overlap
No.1 6
DVDVCR
Date Start End CH Mode
DVD
VCR
VPS
PDC
1. 01/01 12:00 13:00 P01 DVD XP ON
6. 01/01 13:45 21:00 P12 DVD SEP ON
5. 01/01 12:30 14:00 P02 DVD SP ON
1
Press [T-SET] so that the
icon disappears from the front
panel display.
2
Press [TIMER PROG. SHOWVIEW]
twice.
Timer Programming list will appear.
Timer Programming
2. - - -
3. - - -
4. - - -
5. - - -
6. - - -
7. - - -
8. - - -
DVDVCR
Date Start End CH Mode
DVD
VCR
VPS
PDC
1. 01/01 12:00 13:00 P01 DVD XP ON
3
Check the information on the
list you will need.
4
To clear the timer program-
ming, select the desired pro-
gramme using [Cursor K / L],
then press [CLEAR/C-RESET].
To correct the timer program-
ming
1) Select the desired programme
using [Cursor K / L], then
press [ENTER].
2) Correct the timer programming
using [Cursor K / L / { / B].
3) Press [ENTER] again.
5
Press [TIMER PROG. SHOWVIEW]
to exit.
6
Press [T-SET] to return to the
timer-standby mode.
To check the timer program-
ming in process
Press [TIMER PROG. SHOWVIEW].
6
1
Note
• If a timer recording is
proceeding, that programme
is highlighted in red. In such
a case, you cannot select any
other programmes.
• When you check the timer
programming in progress
by pressing [TIMER PROG.
SHOWVIEW] during
operations of the component
(VCR or DVD) which is not
currently used for the timer
recording, the programme
will not be highlighted. In this
case, you cannot select other
programmings.
Checking, cancelling, or correcting the timer
programming information
2
5
6
4
Note
• If you have not set the clock, the clock setting window will appear instead of the Timer Programming
list. Continue from step 4 in “Clock Setting” on page 22 before programming the timer.
• Press [Cursor { / B] to move the cursor in the Timer Programming list.
• If a basic recording or One-touch Timer Recording is in progress on one component (e.g. VCR) and
the timer recording set for the other component (e.g. DVD) is about to begin, the unit automatically
switches to the programmed channel for timer recording 2 minutes before the programmed starting
time, and the recording in progress (for VCR) will be cancelled UNLESS their recording channels are
the same. If their recording channels are the same, the timer recording will start without cancelling the
recording currently in progress. In this case, the recording of the same channel will be made on both
DVD and VCR.
• Cancel the timer-standby mode by pressing [T-SET] before operation for either DVD or VCR. When
finished operating, press [T-SET] to resume the timer-standby mode.
• In the timer-standby mode, you can turn on the power and use the component (VCR or DVD) which is
not currently timer-programmed.