Troubleshooting guide

PLAYING A DISC
To activate the repeat function, press REPEAT during playback.
• The repeat mode changes as described below every time
you press the button.
DVD
NOTES:
• Repeat Title/Chapter is not available with some scenes.
• The REPEAT setting will be cleared when moving to
other title or chapter.
Repeat
• REPEAT are available only during playback.
CHAPTER
TITLE
OFF
(current chapter repeat) (current title repeat) (repeat off)
DVD-RW
ALL
(entire disc repeat)
VR mode
A-B REPEAT
Press A-B REPEAT at your chosen starting point.
• A- appears briefly on the TV screen.
Press A-B REPEAT again at your chosen end point.
• A-B appears briefly on the TV screen, and the repeat
sequence begins.
To exit the sequence, press A-B REPEAT.
NOTES:
• The A-B REPEAT section can only be set within the
current title (for DVDs), or current track (for audio CDs).
• A-B REPEAT is not available with some scenes in DVD.
• To cancel the A point which was set, press CLEAR/C-
RESET.
• A-B REPEAT playback does not function during title,
chapter, track or all repeat playback.
3
2
1
VCDDVD-RWCDDVD
NOTES:
• The REPEAT setting will be cleared when moving to
other track.
• Repeat playback does not function during A-B REPEAT
playback.
To activate the repeat function, press REPEAT during playback.
• The repeat mode changes as described below every time
you press the button.
VCDCD
TRACK
ALL
OFF
(current track repeat) (entire disc repeat)
(repeat
off)
VR mode
without PBC function
JPEGMP3
You may determine the order in which tracks will play.
Press
MODE (playback
must first be stopped).
• The PROGRAM screen
will appear.
Press
▲ or ▼ to select a
track, then press
ENTER.
• Press
CLEAR/C-RESET
to erase the most
recently entered programme.
Press
PLAY to play the programmed tracks.
NOTES:
• While the programme is being played back, the STOP
works as follows.
• Press STOP once and then PLAY again, playback will
restart from the point where STOP was pressed.
(Programme continued)
• Press
STOP twice and then PLAY. Playback starts
from the track in the original order. However, the pro-
gramme can be called back when you follow the above
steps. Your programmes will be stored unless either the
disc tray is opened or power is turned off.
• Up to 99 programmes can be entered.
• To erase all tracks in the programme at once, select
ALL CLEAR at the bottom of the list at step .
• To repeat the current track in the programme, press
REPEAT repeatedly until TRACK appears during
playback. If you like to repeat the entire programme
press
REPEAT repeatedly until ALL appears during
playback.
• Refer to page 24 for programme playback of MP3 and
JPEG.
2
3
2
1
CD
Programme (CD)
0:03:30
CHAPTER TITLE OFF
(current chapter repeat) (
current title repeat) (repeat off)
TRACK
GROUP
OFF
(current track repeat) (current group repeat) (repeat off)
ALL
(entire disc repeat)
–
22
–
EN
During playback, press DIRECT SKIP repeatedly until the
Time Search screen appears.
Within 30 seconds, enter a desired disc time using
numerical buttons.
• Playback will start at the specified time.
• When there is no need to enter a number, “0” appears
automatically. For example, “0:0_:_ _” appears in the
Time Search display if the total time of the disc is less
than 10 minutes.
NOTE:
• Press CLEAR/C-RESET to erase the incorrect input.
2
1
VCDDVD-RWCDDVD
Time Search
VR mode
without PBC function
H9745AD(EN)_v2.qx4 04.9.6 13:19 Page 22
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Sharp Manuals