Troubleshooting guide

EN
VCR OPERATION
To stop a Timer Programme which has already started
Press STOP/EJECT on the VCR/DVD.
NOTE: STOP on the remote control will not function in the
“Timer Recording” mode.
To correct timer programmes
If you want to correct an automatic timer after you finished
setting programme,
Repeat steps to in the “Timer Recording” section.
Select the setting you want to change using sor B.
Enter the correct numbers using K or L, then press B.
Press MENU to exit.
Press TIMER ON/OFF to return to timer stand-by mode.
To cancel or check the start/end time
Repeat steps to in the “Timer Recording”.
Select a programme number you want to check using K
or L. The details of selected programme appears on the
TV screen. You may cancel the entire programme by
pressing s .
Press MENU button to exit.
To avoid overlap of TIMER programmes ...
A timer programme will not work while another programme is
under execution.
Hints for Timer Recording
• If there is a power failure or the VCR/DVD is unplugged for
more than 1 hour, clock and all timer settings will be lost.
• If a tape runs out before a timer recording is finished, the
unit ejects the tape and switches into DVD mode automati-
cally. Press TIMER ON/OFF to active VCR function.
• Once the unit goes into Timer-standby mode, no VCR func-
tions are available until TIMER ON/OFF is pressed. (OUT
PUT on the front panel and VCR on the remote control will
not function.)
• Press TIMER ON/OFF to activate VCR functions after your
timer recording is finished.
• DVD functions are available during Timer-standby mode and
Timer recording. You don’t have to stop your timer recording.
• If the DVD does not be used after you set the VCR/DVD in
Timer-standby mode by pressing TIMER ON/OFF, press
OPERATE to turn off the VCR/DVD.
9:00 10:00 11:00
Programme 1
Programme 2
Programme 3
3
2
21
1
5
4
3
2
31
1
–
17
–
• The index mark will be made automatically when
REC/OTR is pressed. It will also be marked at the starting
point of Timer recording and OTR.
• The index mark is not recorded if STILL/PAUSE is
pressed and released during recording.
• The time gap between index marks on the tape should be
greater than 1 minute for SP recording and 2 minutes for
LP recording.
Press
VCR, then SEARCH MODE.
Press K or L repeatedly until the number of pro-
grammes that you want to skip appears.
Press s or B.
The VCR/DVD begins rewinding or fast forwarding to the
beginning of desired programme.
• When the preset programme is reached, the VCR/DVD
will start playback automatically.
NOTES:
• Index Search can be set up to 20.
• This function will not operate in the Recording mode.
• Operations must be followed up within 30 seconds,
from steps to . Otherwise the Index Search
mode will be cancelled.
• To exit the Index Search mode, press MENU in step
. Or press STOP after step .
32
32
3
2
1
Index Search
If a tape includes both programmes recorded in the PAL sys-
tem and ones recorded in the NTSC system, this function
may not be operated correctly.
Press
VCR, then SEARCH MODE twice.
Press K or L repeatedly until the desired time appears.
Press s or B.
The VCR/DVD begins rewinding or fast forwarding to the
specified point.
When 0:00 is reached, the VCR/DVD will start playback auto-
matically.
NOTES:
• Time Search can be set up to 9 hours 59 minutes
(9:59).
• This function will not operate in the Recording mode.
• Operations must be followed up within 30 seconds,
from steps to . Otherwise the Time Search mode
will be cancelled.
• To exit the Time Search mode, press MENU in step .
Or press STOP after step .
3
2
32
3
2
1
Time Search
H9745AD(EN)_v2.qx4 04.9.6 13:19 Page 17
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Sharp Manuals