User Manual
EN
VCR OPERATION
To stop a Timer Programme which has already started
Press STOP/EJECT on the VCR/DVD.
NOTE: STOP on the remote control will not function in the
“Timer Recording” mode.
To correct timer programmes
If you want to correct an automatic timer after you finished
setting programme,
Repeat steps to in the “Timer Recording” section.
Select the setting you want to change using s or B.
Enter the correct numbers using K or L, then press B.
Press MENU to exit.
Press TIMER ON/OFF to return to timer stand-by mode.
To cancel or check the start/end time
Repeat steps to in the “Timer Recording”.
Select a programme number you want to check using K
or L. The details of selected programme appears on the
TV screen. You may cancel the entire programme by
pressing s .
Press MENU button to exit.
To avoid overlap of TIMER programmes ...
A timer programme will not work while another programme is
under execution.
Hints for Timer Recording
• If there is a power failure or the VCR/DVD is unplugged for
more than 1 hour, clock and all timer settings will be lost.
• If a tape runs out before a timer recording is finished, the
unit ejects the tape and switches into DVD mode automati-
cally. Press TIMER ON/OFF to active VCR function.
• Once the unit goes into Timer-standby mode, no VCR func-
tions are available until TIMER ON/OFF is pressed. (OUT
PUT on the front panel and VCR on the remote control will
not function.)
• Press TIMER ON/OFF to activate VCR functions after your
timer recording is finished.
• DVD functions are available during Timer-standby mode and
Timer recording. You don’t have to stop your timer recording.
• If the DVD does not be used after you set the VCR/DVD in
Timer-standby mode by pressing TIMER ON/OFF, press
OPERATE to turn off the VCR/DVD.
9:00 10:00 11:00
Programme 1
Programme 2
Programme 3
3
2
21
1
5
4
3
2
31
1
SHOWVIEW
®
Guide Channel Set
Setting the guide channels for the SHOWVIEW system
First, fill in the boxes below:
Write your local channel numbers in “VCR Channel”
columns, corresponding “TV-Station” and “GUIDE Channel”
columns, using your TV guide magazine or the TV listings of
your local newspaper.
Now, compare the channel numbers you have written in the
GUIDE Channel and VCR Channel columns. You must set all
of these channel numbers that do not match using the follow-
ing procedure before you programme the automatic timer
recording using the SHOWVIEW system.
• This setting only needs to be set once, but must be done
again if you use this VCR/DVD in another area by moving it.
Press MENU.
Press K or L to select INITIAL, then press B.
Press K or L to select GUIDE CHANNEL, then press B.
Press K or L to select the relevant mode, then press B.
•To set the guide channel individually, select MANUAL.
Then press B and continue with step .
•To set all of the guide channels to AV1, AV2 or AV3
select “AV1”, “AV2” or “AV3”. Then press MENU to exit.
Press K or L repeatedly to select the position number,
then press B.
Press the numerical buttons, K or L to enter guide
channel number, then press B.
• Press s to erase all digit.
•You can select guide channels 1-255.
•To select channels from 1 to 9, first press “0” twice then
1 to 9.
•To select channels from 10 to 99, first press “0” once
then press the last two digits. (To select channel 80,
first press “0” then press “8” and “0”).
Press MENU to exit.
7
6
5
5
4
3
2
1
–
17
–
GUIDE
Channel
TV-Station
VCR
Channel
Timer Recording Using the S
HOW
V
IEW
System
You can programme the timer using the SHOWVIEW programme
numbers that are printed in TV guide magazine. You can set 8
programmes to record.
• Insert a cassette tape with its erase prevention tab in place.
(If necessary, rewind or fast forward the tape to the point at
which you want to begin recording.)
Press the
SHOWVIEW buttons.
NOTE: If you have not set the clock yet, the CLOCK setting
menu will appear. If so , follow the steps outlined in
the “Setting the Clock”. Then, set the timer.
Press the numerical buttons to set the SHOWVIEW num-
ber of the programme you want to record.
• Press s to go back one digit from current digit while
you set the SHOWVIEW number.
• FOR ONCE-ONLY RECORDING : Press the SHOWVIEW
button.
3
2
1