DVD RECORDER WITH HARD DISC MODEL DV-HR480H DV-HR400H OPERATION MANUAL PAL 2 If you require any advice or assistance regarding your Sharp product, please visit our web-site www.sharp.co.uk/customersupport. Customers without Internet access may telephone 08705 274277 during office hours(or (01) 6760648 if telephoning from Ireland). • The region number for this Recorder is 2.
SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 5A fuse. Should the fuse need to be replaced, a or approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
SAFETY INFORMATION Note: This Recorder can be used only where the power supply is AC 220V-240V, 50Hz. It cannot be used elsewhere. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. AS THE LASER BEAM USED IN THIS RECORDER IS HARMFUL TO THE EYES, DO NOT ATTEMPT TO DISASSEMBLE THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Contents SAFETY INFORMATION .............................. 1 Channel Setting ........................................... 29 Features ....................................................... 4 Accessories ................................................. 6 Channel Setting ............................................................. Deleting Channels .......................................................... Re-naming Channels .....................................................
Contents DVD/CD Playback ........................................ 69 Enjoying High Quality Sounds ................... 98 Loading Disc .................................................................. Playback from REC LIST ............................................... DVD-RW(Video format)/DVD-R Playback ...................... DVD Video Playback ...................................................... Audio CD/Video CD Playback ........................................ Other Types of Playback .............
Features The DV-HR480H/DV-HR400H DVD Recorder with Hard Disc realises easy programming with the GUIDE Plus+ system, and up to 48x high-speed dubbing. 1 “DVD Multi-Play” can play 5 types of recordable DVD discs • Besides DVD-RW, DVD-R, DVD+RW *1 and DVD+R *1 discs, it can also play DVD-RAM *2 discs. Even a DVD borrowed from a friend can be played no matter what format it uses. *1 *2 Only the discs recorded in a video format and finalised can be played. DVD-RAM Version 2 discs with a 4.7GB or 9.
Features 7 Speed viewing and speed listening (Rapid play) • Plays a disc at 1.5 times faster than normal speed with sound. It lets you check lengthy recorded programmes quickly and easily. 8 32-step manual rate video recording • The video recording mode can be selected form 32 steps, including four basic steps of high image quality (XP), standard (SP), x2 (LP) and x3 (EP) . You may choose one from these steps for optimal image quality depending on the amount of free memory remaining on the disc.
Accessories Remote control unit Two R-03 size batteries (“AAA” size, UM/SUM-4) for the remote control unit Video/audio cable Qu ick Sta rt G uid e Quick Start Guide (TINS-B782WJZZ) RF coaxial cable A. Information on Disposal for Users (private households) 1. In the European Union Attention: Your product is marked with this symbol. It means that used electrical and electronic products should not be mixed with general household waste. There is a separate collection system for these products.
Precautions about Using This Product Do not use at locations at high temperature. • If you leave this equipment at a location which rises to an abnormally high temperature (like the inside of a car with the windows shut), this may cause deformation of the cabinet or malfunction. Be very careful not to allow the area around the Recorder or discs to reach a high temperature. Avoid dust and smoke.
Precautions about Using This Product Upkeep of cabinet • The cabinet surface employs a lot of plastic. Do not wipe these surfaces with benzene or thinner because this may cause deterioration or paint peeling. • In the unlikely event that the hard disc (HDD) malfunctions for some reason, you cannot replace it by yourself. If you disassemble the Recorder you will void the warranty. Please contact the nearest service centre approved by Sharp.
About Hard Disc (HDD) This Recorder has a built in hard disc (abbreviated as “HDD”) for recording and playback. Beware of the following points when setting up and using the Recorder. Failure to observe precautions may cause damage to the HDD itself or its content, failure of the disc to operate, or recording of noise. • Do not subject the Recorder to any vibration or impact. • Do not place the Recorder in a cramped location which might block the cooling fan or ventilation port on the back of the Recorder.
About DVD A Quick Reference for Selecting Discs The following is a quick reference to see what discs can/ cannot be used with this recorder. Each disc has a compatible Recording Format(s). Also, there are some constraints. For detailed and exact information, read the explanations in pages 10 and 11.
About DVD Discs that Cannot Be Used with This Recorder ■ The following discs are unable to be played back or are not played back properly on this Recorder. If such a disc is mistakenly played back, the speakers may be damaged due to the large volume. Never attempt to play back such discs. CDG, Photo CD, CD-ROM, CD-TEXT, SVCD, SACD, PD, CDV, CVD, DVD-ROM, DVD-Audio ■ Discs with unusual shapes cannot be played. • Discs with unusual shapes (heart-shaped or hexagonal discs, etc.) cannot be used.
About DVD Æ When using the unit to play a CD-RW/R disc with still images stored (recorded). • With CD-RW/R discs on which still images are mixed in with music or movies, you will be able to play only the still images. You may not be able to play some of these discs at all. • This unit can recognize a maximum of 256 folders arranged in up to 8 hierarchical levels. The maximum number of files recognized is 4,096 files. • Multi-session discs cannot be played.
About DVD Recording Formats • There are two recording formats available with this Recorder: the VR mode and the Video mode. • The recording format that can be selected may differ depending on the disc. Refer to the section on Types of Discs for Recording (page 12). • Recording in the VR mode and Video mode cannot be mixed on one disc. VR (Video Recording) Mode The VR mode is the basic DVD-RW recording format, and lets you enjoy the various editing functions available with this Recorder.
About DVD Using the Proper Disc Unrecordable Material Select the disc and recording format to be used according to the objective of the recording. Select the disc and recording format by referring to the table below. Objective • When you want to play back a recorded disc with a DVD player or DVD Video compatible PC • When you want to repeatedly record and erase a recorded disc Disc to Use Recording Format Recordable Video mode DVD-RW disc recording Ver.1.1, + Ver.1.1 (CPRM finalisation compatible), Ver.
Initialisation and Finalisation Initialisation (Formatting) Initialisation is required when using DVD-RW discs in the Video mode. (See page 96 for details about Initialisation.) When an unused DVD-RW disc is placed in the Recorder immediately after the disc has been purchased, the Recorder is set to automatically begin initialising in the VR mode. The settings can also be changed so that discs are initialised in the Video mode (“DVD AUTO INITIALISE” on page 105).
About the Contents of the Disc Icons Used on DVD Video Disc Case The back of the case of a DVD that is commercially available usually contains various information about the contents of the disc. 1 2 2 1. English 2. Chinese 3 2 4 16:9 LB 1. English 2. Chinese c Screen aspect ratio Movies are shot in a variety of screen modes.
Important Information Disc Precautions Be Careful of Scratches and Dust • DVD-RW and DVD-R discs are sensitive to dust, fingerprints and especially scratches. A scratched disc may not be able to be recorded, or important data recorded may not be able to be played back. Handle discs with care and store them in a safe place. Proper Disc Storage Place the disc in the centre of the disc case and store the case and disc upright.
Major Components Main Unit (Front) 1 2 3 18 6 7 1 2 3 4 5 4 8 9 10 11 12 5 8 9 10 11 12 13 14 15 16 17 18 13 14 15 16 17 6 7 OPERATE (p. 25) STANDBY indicator (p. 25) TIMER indicator (p. 49) Disc tray (p. 41) OPEN/CLOSE (p. 41) RESET (p. 120) LINE IN 3 (p. 103) • AUDIO Input jacks • VIDEO Input jack • S-VIDEO Input jack DV IN terminal (DV-HR480H only) (p. 100) HDD REC STOP (p. 40) HDD Æ REC (p. 35) HDD ■ STOP (p. 35) HDD | PLAY (p. 35) DVD | PLAY (p. 35) DVD ■ STOP (p. 35) DVD Æ REC (p.
Major Components Remote Control Unit 1 2 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 3 * 4 5 6 7 8 9 10 11 12 13 14 15 16 17 38 39 40 41 42 43 44 45 46 *( button) To change between single digit and two-digit channel numbers, press the key with “*” above (below 7 key). For example, to enter “24”, press this key and then “24”. Also this key is used to switch between UHF/VHF and CATV in the case of Manual Tuning.
Major Components Loading the Batteries 1 • • • • • While pressing Y down, slide the battery cover in the direction of the arrow. 2 Load the batteries. Load the two R-03 size batteries (“AAA” size, UM/SUM-4) supplied with the remote control unit. Make sure that the battery poles and are positioned as indicated. Slide the battery cover in the direction of the arrow until it clicks. NOTE Do not subject the remote control unit to shock, water or excessive humidity.
Major Components Operating a TV Using the Remote Control (Universal Remote Control) The Universal Remote Control may operate the basic functions of 18 different types of TVs. To enter the Manufacturer’s Code for your TV, follow the instructions below. There is no guarantee that the universal remote control will function with your TV. Setting the Manufacturer’s Code 1 2 3 Press OPERATE of TV CONTROL and CH ' of TV CONTROL simultaneously. Enter the 2-digit Manufacturer’s Code with the Number buttons (Ex.
Major Components Setting the Remote Control Code • Two types of remote control codes operate this Recorder: RC-1 and RC-2. If you operate this Recorder by remote control along with another SHARP DVD recorder or DVD player placed next to it simultaneously, switching the remote control code (both the Recorder and remote control) to one of the signals (RC-1 or RC-2) will let you operate only with this Recorder. • Make sure to set the Recorder and remote control to the same remote code.
Basic Connection Connection Using Aerial Cables and SCART Cables The following connection is the basic connection to watch or record TV programmes. 1 2 Important! • Be sure to turn off and unplug from the AC outlet this Recorder and all equipment before connecting the cables. • Read through the operation manual for the equipment to be connected. 3 NOTE • To connect using S-video or component cables, see “Using Other Types of Video Output” on page 24.
Basic Connection Using Other Types of Video Output In order to view clearer DVD images, it is recommended that you use a commercially available S-video or component video cable when connecting your TV to the video output. Connecting Using an S-video or Video/ Audio Cable TV Connect the S-VIDEO or VIDEO Output jack on this Recorder to the S-video or video input jack on your TV using an S-video cable (commercially available) or Video/Audio cable (supplied).
Auto Installation Turning the Power On Press OPERATE on the remote control or Recorder to turn on the Recorder’s power. • When you turn on the Recorder’s power, the HDD and DVD mode indicators will blink on the Front Panel Display. During the blinking stage, system processing is in progress. Wait until the blinking stops and the HDD mode indicator turns on. • When the Recorder power is turned on for the first time after purchase, the “AUTO INSTALLATION” screen is displayed.
Auto Installation 3 All available terrestrial channels will be automatically installed. 4 • Refer to “Clock Setting” on page 28. ■ When connecting with SCART cable AUTO INSTALLATION [AUTO TUNING] The “CLOCK” setting screen is automatically displayed. AUTO INSTALLATION [CLOCK] 24 / 12 [SAT] 10 : 28 24 / 12 [SAT] 10 : 28 SET THE CURRENT DATE AND TIME TIME PLEASE WAIT. DOWNLOADING.
About START MENU About START MENU With this Recorder, you can call up functions like Playback, Edit and Other Settings from the “START MENU”. For details on operation procedures, see the page explaining each option. 1 2 3 START MENU [REC LIST] 24 / 12 [SAT] 10 : 28 DISPLAYS THE RECORDED PROGRAM AS A TABLE. AND THEN PLAY BACK/EDIT, ETC. 4 1 REC LIST DISPLAYS THE RECORDED PROGRAMME AS A TABLE. AND THEN PLAY BACK/EDIT, ETC.
Clock Setting 6 Clock Setting • For example, for 24th December enter 24 and 12 respectively. The clock will normally be set using the VPS/PDC information when your Recorder automatically tunes in the broadcast channels. If for any reason the VPS/PDC signals are not present, your Recorder will not be able to set the clock. This procedure will allow you to set the clock. 1 Enter the “DAY”, then “MONTH” as per Step 5.
Channel Setting Channel Setting This Recorder can receive a maximum of 84 channels as shown below by presetting the channels into memory. (UHF: E21–E69) 1 2 Press START MENU to display the “START MENU” screen. Press ' / " / \ / | to select (“OTHER SETTINGS”), then press SET/ENTER. START MENU [OTHER SETTINGS] 24 / 12 [SAT] 10 : 28 8 Press ' / " to select “FINE TUNING”. Then press and hold \ / | until the sharpest colour picture is obtained. 9 Press ' / " to select “DECODER”. This is preset to “OFF”.
Channel Setting Deleting Channels Re-naming Channels If there is a channel you want to delete from the Recorder memory, follow the procedure below. 1 2 Press START MENU to display the “START MENU” screen. Press ' / " / \ / | to select (“OTHER SETTINGS”), then press SET/ENTER. 3 Press \ / | to select “VIEW/PLAY SET”. 4 Press ' / " to select “CHANNEL SETTING”, then press SET/ ENTER. 5 Press ' / " to select “DELETE”, then press SET/ENTER. 6 Press ' / " / \ / | to highlight the channel to be deleted
Post Code Post Code Security Changing PIN NUMBER This feature should allow the Police to identify you as the owner of the Recorder if it is stolen. Each time the Recorder is turned on, your postcode will be displayed for 5 seconds. Your postcode cannot be changed or removed without first entering the correct PIN-number. If you would like to use this function, follow the procedure below. You can change your PIN number at any time with the following procedure.
Display Information • When pressed during live broadcast, the channel information (see left) is displayed. • The HDD information screen is displayed as follows, when pressed during playback. Channel Information When the power is turned on or the channel is switched, channel information is displayed as follows: 2 PR 2 BBC NICAM STEREO L R 3 HD D OR IG IN AL DVD-RW VR ORIGINAL XP REMAIN 0h10m 1 X P REMAIN 19 h10m 12 3 4 5 4 5 Display automatically disappears in 5 seconds.
Display Information Checking Remaining Time of DVD and Number of Titles 2 • When pressed during playback, the screen changes to the counter display. When the DVD mode indicator is displayed on the Front Panel Display (DVD mode) 1 Press ON SCREEN (under the cover) or DVD again. 0 0:00:24 / 0 0:20:00 Press ON SCREEN (under the cover) or DVD. • When pressed during live broadcast, the channel information (see the left top screen or page 32) is displayed.
Display Information Switching Front Panel Display Turning off the LCD Backlight If you think the backlight is obtrusive, e.g. during Timer Recording at night, you can turn the backlight off. Front Panel Display 1 Press OPERATE to turn the power on. • Channel display (when watching TV) • Counter display (during playback/ recording) 2 Hour Minute Second Press DISPLAY (under the cover).
Preparation to Operate This Recorder HDD DVD-RW DVD-RW VR MODE VIDEO MODE DVD-R DVD VIDEO VIDEO CD AUDIO CD CD-R MP3 WMA CD-RW MP3 CD-RW JPEG JPEG Some operations such as "OPERATE" (turn on/stand by), "RECORD" and "PLAY"(both HDD and DVD) can be done by buttons both on the Remote Control and the Recorder. = Remote Control CD-R WMA The Recorder + = on HDD (left) side + = on DVD (right) side Remote Control The Recorder The same thing applies to REC STOP and STOP buttons.
Time Shift Viewing/Chasing Playback With this Recorder, you can enjoy Time Shift Viewing and Chasing Playback—distinctive features of an HDD. 1 Time Shift Viewing 2 Chasing Playback While you are watching a programme, the phone rings.... At times like this, you can pause the programme at the press of a button and watch the rest later. You return home earlier than expected while timer recording is in progress....
Time Shift Viewing/Chasing Playback • When you select Fast Forward Playback (Forward only) you can enjoy audio together with video (Rapid playback). • Press |PLAY to return to the normal playback speed. Time Shift Viewing HDD NOTE • If scheduled recording of a programme starts during Time Shift viewing, the Time Shift viewing will stop and the broadcast screen (live) of the channel being recorded will appear. • Time Shift viewing is not possible when inputting DV.
Recording to HDD This section explains recording on the hard disc (HDD). (For information on recording to DVD, see page 41.) Confirming Remaining Time for Recording To confirm on the TV screen • Press ON SCREEN (under the cover). To confirm on the Front Panel Display • Press DISPLAY (under the cover). * Information such as the remaining time on the disc, the number of titles recorded is displayed. Checking this information before recording is recommended.
Recording to HDD High-Speed Dubbing Priority (Page 59) • This Recorder has a high-speed dubbing function. The High-Speed Dubbing Priority function can be used when dubbing from HDD to video format DVD. • This setting must be specified in advance when performing high-speed dubbing from HDD to an DVD-R or video format DVD-RW disc. • If you set high-speed dubbing priority, there will be restrictions, such as the inability to edit at the frame level, when you edit the video.
Recording to HDD 4 Press Æ REC during broadcast viewing. • To perform recording by operating the controls on the Recorder, press the Æ REC button on the HDD side (left). • Recording begins and REC icon is displayed in TV screen. • Æ REC on the HDD (left) side of the Recorder is lit during recording. REC icon REC 5 Press REC PAUSE to pause recording. • Record Pause does not work during Chasing Playback. • During pause, Æ REC on the HDD (left) side of the Recorder blinks.
Recording to DVD This section explains recording on the DVD (For information on recording to HDD, see page 38.) Checking Remaining Time and Other Information Press ON SCREEN (under the cover) during DVD playback or recording. • Disc capacity and the number of recorded titles, etc. are displayed. It is recommended to confirm before recording.
Recording to DVD 2 Set a DVD-RW or DVD-R disc. • When a new uninitialised DVD-RW disc is set, the Recorder automatically starts initialising it in VR mode. When initialising is over, you can start recording. • When you want to re-initialise in Video mode, select “DVD INITIALISE (VIDEO)” screen (page 96). • When you want to initialise all the discs automatically in Video mode, select “DVD AUTO INITIALISE” screen (page 105). 3 4 Press Number buttons or CH ' / " to select the channel to record.
Setting the Recording Mode (HDD/DVD) • The HDD recording time is in approximate figures. DVD recording time is in approximate figures when 4.7GB discs are used. • The figures below are not guaranteed in every instance. Actual maximum recordable time may be shorter than indicated below, depending on image quality and other factors. The HDD Remaining Time displayed on the TV screen is an estimate of the shortest remaining time for recording.
Setting the Recording Mode (HDD/DVD) Setting the Manual Recording Mode (MN) HDD DVD-RW DVD-RW VR MODE VIDEO MODE DVD-R You can set the manual recording mode which is used when you select “MNgg” with REC MODE. 1 Press START MENU to display the “START MENU” screen. Direct Recording the TV programme you are watching HDD DVD-RW VR MODE VIDEO MODE DVD-R Important! • This function is available only when connecting to your TV that has AV Link function, using SCART cable.
Timer Recording/The GUIDE Plus+® System NOTE • In areas where Host Channels cannot be received or data from the Host Channels do not download, some features of the GUIDE Plus+ system such as TV listings data and One-Button Recording are not available. If you are located in such an area, other features such as Manual Recording (Page 53) are available. For the table of Host Channels, see page 47.
Timer Recording/The GUIDE Plus+® System The GUIDE Plus+ Setup 4 Preparation before the GUIDE Plus+ setup • Complete the connection of your equipment (the Recorder, TV, aerial, external tuner if applicable). See page 23 for basic connection. Please note that if you use an external receiver (such as Satellite tuner), you have to connect the plug of G-LINK cable to the back of the Recorder and place the other end in front of the tuner.
Timer Recording/The GUIDE Plus+® System 2 3 Press GUIDE to display the GUIDE Plus+ setup menu screen. Press ' / " to select “Postal Code”. Press SET/ENTER, then press ' / " / \ / | to enter your postal code. Then, using ' / " , select “External Receiver 1” and set the details. Select (1) your reception (terrestrial, cable or satellite), (2) your provider, (3) the brand of your external receiver and (4) the terminal which your external receiver is plugged into (SCART 2).
Timer Recording/The GUIDE Plus+® System Alternate Setup If your external receiver is not in the list or your external receiver could not be controlled properly by the Recorder, please try the following: 1. At Step 3 of page 47, select “None” (at the end of the list) for External Receiver Brand. 2. Press GUIDE to exit the Setup menu. 3. Tune your external receiver to your “Host Channel” (see list of Host Channels in Step 5) and leave it “ON” overnight (the Recorder must be on “STANDBY” overnight). 4.
Timer Recording/The GUIDE Plus+® System The “One-Button-Record” Feature This is the most convenient feature for Timer Recording that the GUIDE Plus+ System accommodates. The One-Button Record feature is available anytime you can highlight a programme tile. This can be in the Grid, after a search for a certain category or in your recommendations under My TV. NOTE • During the Timer Standby mode, you cannot edit or add a timer programme. To edit or add a timer programme, cancel Timer Standby mode first.
Timer Recording/The GUIDE Plus+® System Browse, Search, etc... Browse the Grid The Grid screen is the main TV listings screen of the GUIDE Plus+ system. It provides you with seven days of TV listings information starting with the current day and time and the top channel. The Search Area allows you to locate programme listings by category (e.g. Movies, Sport, etc.), subcategory (e.g. Action, Comedy) or via personal keywords (My Choice).
Timer Recording/The GUIDE Plus+® System My TV The “My TV” Area allows you to set up a personal profile. You can define a profile by channels, themes and / or by keywords. As soon as a personal profile has been set, the GUIDE Plus+ system is scanning automatically and continuously the TV listings data for the next seven days. Every time you are accessing the “My TV” Area, a list of programmes is displayed according to your profile.
Timer Recording/The GUIDE Plus+® System 3 7 Press Red (A) to display the VIDEO Plus+ screen. P 00 1-Sep 16:51 Cancel Home Please enter the PlusCode number and press ENTER to confirm. = = = = = = = = = Search My TV Schedule Record Schedule Info Mode Freq. Dest. SP Once HDD 1-Sep 16:20 17:00 BBC1 SP Once HDD 1-Sep 18:00 19:00 ITV1 LP Once DVD 8 9 4 Press Number buttons to enter the PlusCode number.
Timer Recording/The GUIDE Plus+® System • When you set a DVD as recording media, timer recording will not start during disc playback. If “ALTERNATIVE REC SETTING” is set to “YES”, the programme will be timer recorded to HDD. • Timer recording will not start during dubbing. • Manual recording and editing cannot be performed during timer standby. 3 P 00 1-Sep 17:18 Preparation for Timer Recording • Check that the clock is displaying the correct time.
Timer Recording/The GUIDE Plus+® System 7 8 9 Press RED (A) to select “Mode” (Rec. Mode). With each press, the selected option shifts (page 52). Press Green (B) to select “Frequency” (page 52). Press Yellow (C) to select “Destination” (page 52). 10 Press | to proceed to the next right recording tile(“Timing”). Press Yellow (C) to enter extra time to add at the end or select VPS/PDC (page 52). • If any more timer recordings are to be set, repeat steps 3 to 10.
Timer Recording/The GUIDE Plus+® System Editing (Confirm, Change and Cancel) a Timer Programme HDD DVD-RW DVD-RW VR MODE VIDEO MODE DVD-R Changing 1 2 Press ' / " to highlight the scheduled event that you would like to edit. 3 Press \ / | to highlight the setting to be changed and correct it by using the corresponding colour buttons, ' / " / \ / | or the Number buttons. The operation method is the same for both HDD and DVD.
Timer Recording/The GUIDE Plus+® System Other Functions of the GUIDE Plus+ System Lock/Unlock Video Window When you enter the GUIDE Plus+ system the channel you were watching remains visible in the video window (Top left part of the screen, see the screen image below). The date stamp above the window lets you know what channel, day and time it is. The default setting for the video window is “locked”. The lock icon above the video window displays a “closed” lock.
Timer Recording/The GUIDE Plus+® System Configure the GUIDE Plus+ System You can configure the GUIDE Plus+ system from the “Setup” Area. Here, you can set/change your language, country and postal code. Also you can add/ change your external receivers details. These can be done in the “Setup” area. NOTE • It is very important that you enter correct settings for the post code for your current domicile in order to receive TV listings correctly. • Some changes (e.g.
Dubbing (HDD/DVD) See the table below for details. DVD-RAM — — DVD+RW/R — — Dubbing Direction and Dubbing Speed Dubbing Direction Dubbing Constant Speed Speed (Rate Conversion Dubbing) High Speed (High Speed Dubbing) HDD→DVD-RW (VR mode) ✕ ✕ HDD→DVD-RW/R (Video mode) ✕ √ DVD-RW→HDD (VR mode) ✕ DVD-RW/R→HDD (Video mode) *2 ✕ *1 ✕ — ✕ Can dub. — Cannot dub. √ Can High Speed Dub the recorded title if it is recorded using “HI SP DUB PRIORITY”.
Dubbing (HDD/DVD) Rate Conversion Dubbing and High Speed Dubbing Rate Conversion Dubbing Plays back titles of HDD and dubs to DVD-RW/R or plays back titles of DVD-RW/R and dubs to HDD. • Picture quality (recording mode) for dubbing can be selected. You can select among 32 levels of recording modes so it is convenient when you want to fit the programmes into one disc. • You can select among 32 levels of recording mode by using Manual setting but picture quality will not exceed that of the original.
Dubbing (HDD/DVD) Limitation during Dubbing You cannot dub from HDD to DVD-RW/R in the following cases. • Total number of titles in DVD-RW/R reached 99 or total number of chapters reached 999. • HDD or DVD-RW/R is either recording or playing back. • The DVD-RW/R disc is protected. • The DVD-RW/R disc is full. You cannot dub from DVD-RW/R to HDD in the following cases. • Not enough HDD capacity.
Dubbing (HDD/DVD) When dubbing in chapter units, press Red (A) (THUMBNAIL), and then Green (B) (CHAPTER). You can select only the chapters within a single title. Dubbing (HDD↔DVD)/ High Speed Dubbing (HDD→DVD) HDD DVD-RW DVD-RW VR MODE VIDEO MODE • Setting toggles between “dubbing” and “dubbing cancelled” each time you press SET/ENTER. • Select more titles when you want to dub multiple titles. (You can dub up to 10 titles at once.
Dubbing (HDD/DVD) Selecting Exact Dubbing • Select Exact Dubbing when there are multiple titles (up to 10) you want to dub and you know you cannot fit all into one disc. The Recorder will select the appropriate recording mode and fit all titles into one disc (maximum 6 hours). • You cannot dub titles in higher quality than the original. • The Recorder will lower the recording mode when there is not enough capacity in the disc to dub compared to the length of all the titles (programmes).
Eliminating Problems (Recording, Timer Recording, Dubbing) When You Cannot Record Problem • • • • • • No disc in the Recorder. Unrecordable disc is loaded. Not enough disc capacity. Recorder cannot identify the disc. Disc is protected. Not enough HDD capacity. • In the middle of dubbing. Suggested Solution • Load recordable DVD. • • • • Load recordable DVD with enough capacity. Please wait until the disc is recognized. Cancel disc protection or change to new DVD for recording.
Eliminating Problems (Recording, Timer Recording, Dubbing) When You Cannot Timer Record Problem • • • • • No disc in the Recorder. Unrecordable disc is loaded. Not enough disc capacity. Recorder cannot identify the disc. Disc is protected. • Not enough HDD capacity. • Number of timer programmes set has reached the limit. • Dubbing is in progress. • Playing back the DVD. • In the middle of editing the DVD disc. • The GUIDE Plus+ screen is completely empty or some information (such as logos) are missing.
HDD Playback • Press Red (A) (THUMBNAIL) to switch from title list to thumbnail. • Press Green (B) to sort the titles. They can be sorted by the following order types: “FROM NEW”, “FROM OLD” and “TITLES”. REC LIST: If you select the programme you want to watch from the list of recorded programmes (REC LIST) and press SET/ ENTER, playback will begin. NOTE • To display the counter during playback, press ON SCREEN (under the cover) (page 32).
HDD Playback Resume playback function • If you press |PLAY again, playback will resume from the point where it was previously stopped. • To playback from the beginning, follow the procedure below: 1Select the title to play back from Rec List and press Blue (D). 2Press ' / " to select “PLAYBACK”, then SET/ENTER. 3Press \ / | to select “FROM BEGINNING”, then SET/ENTER. NOTE • For titles of VR mode, it is the image of about 2 minutes after the start of the recording that is displayed as Thumbnail.
HDD Playback Other Types of Playback HDD • This section explains other types of HDD playback operations. Slow Playback This lets you playback video at slow speed. 1 (Approx. 1/2 x) Use to fast forward/reverse programmes being played. Press JFWD or GREV during playback. 2 ( (Approx. 8x) (Approx. 32x) Fast Reverse is Approx. 2x) Fast Forward • When you select Playback (Forward only) you can enjoy audio together with video (Rapid play). 2 Press |PLAY to cancel the search.
HDD Playback 4 Switching Audio Example: Repeat playback of a title (TITLE) You can change the audio output channel during HDD playback. Each time AUDIO (under the cover) is pressed, the audio channels change. • The way audio channels change differs depending on the sound recorded on HDD. See the table on page 109 for details. NOTE • When you play a programme recorded in stereo or monaural, and if you are listening to the BIT STREAM sound via the digital output jack, you cannot select the audio channel.
DVD/CD Playback This section explains playback of DVD-RW/R discs recorded with this Recorder, commercially available DVD Video discs (such as movies) and CDs. • To playback a DVD-RW/R recorded with this Recorder, select the title to be played back, and then start playback. • Display the list of initial images (thumbnails) for each title, and select a title. (REC LIST) 4 1 BBC 2 21 / 5 2 5 SAT 10 : 00PM Press OPEN/CLOSE to open the disc tray. 6 Place a disc onto the disc tray. 60 m.
DVD/CD Playback DVD-RW (Video format) /DVD-R Playback Playback from beginning 1 Press DVD to select DVD mode. • The DVD mode indicator on the Front Panel Display appears. • HDD mode is the default setting when the power is turned on. 2 3 Load a disc recorded in Video mode. Press |PLAY. • Playback begins from title 1. Playback by Selecting Title • To play back a disc recorded and finalised in Video mode, press DVD TOP MENU, display the TITLE LIST screen, and select a title to play back.
DVD/CD Playback Audio CD/Video CD Playback Other Types of Playback VIDEO CD DVD-RW DVD-RW VR MODE VIDEO MODE AUDIO CD DVD-R DVD VIDEO VIDEO CD AUDIO CD Preparation Press DVD and load a disc. • The DVD mode indicator on the Front Panel Display appears. Playback from the beginning 1 Press |PLAY. • Playback begins from the first track. 2 To stop playback, press ■STOP/ LIVE. Playback by selecting the track 1 1 Press DIRECT. • DIRECT does not work when playing back a video CD with PBC on.
DVD/CD Playback Skipping to Next or Start of Current Chapter (Track) Skipping (to the beginning of a chapter or track) functions when Lor Kis pressed during playback. • Press Lto go to the start of the next chapter. • Press Konce to return to the start of current chapter (track). If you press it again (within about 5 seconds), it will skip to the beginning of the previous chapter (track). • This function does not work during Time Shift Viewing.
DVD/CD Playback 4 Press SET/ENTER when you reach the scene you want to end Repeat Playback. • The end point of the part (B) will be memorized and the Repeat Playback for the specified part (A-B) starts. 5 • • • • • Press (INPUT) to return to normal playback. NOTE For Partial Repeat Playback, set the start and end points within the same title. Repeat Playback will not work during PBC playback of a video CD with PBC (Playback Control). Repeat Playback may be forbidden depending on the disc.
DVD/CD Playback Switching between functions • You can switch subtitle, angle and audio at the Function Control screen (page 77). • Operation for each function varies depending on the disc. See the manual for the disc. Fast Forward/Reverse • You cannot perform Fast Forward/Fast Reverse over a boundary between titles. At the end or beginning of the title, Fast Forward/Fast Reverse will be cancelled and normal playback will be selected automatically.
MP3/WMA File Playback CD-R CD-RW MP3 WMA MP3 WMA NOTE • See page 11 for details about the MP3 file format. • See page 12 for details about the WMA file format. 1 2 Press DVD to select DVD mode. Load an MP3/WMA recorded CD-R or the CD-RW, then press DVD MENU. To Play Another File (music title) during Playback 1 2 Press ■STOP/LIVE to stop playback. Press ' / " / \ / | to select the file (music title) you want to play, then press SET/ENTER. • The chosen file (music title) will be played.
JPEG File Playback CD-R JPEG CD-RW JPEG NOTE • This Recorder can play still images (JPEG files) that have been recorded on CD-RW/R discs. For details on the still images that you can play using this Recorder, refer to “About JPEG file format” on page 11. • During “Normal play”, still images are played one by one while during “Slide show”, they are automatically replaced one after another. Playing back still images in sequence 1 Load the disc containing the still images, and press |PLAY.
Settings During Playback Function Control Operation Procedure Function Control HDD DVD-RW DVD-RW VR MODE VIDEO MODE DVD-R DVD VIDEO This lets you make various settings at once, like subtitle and angle setting, and title selection for Direct Playback. Depending on your preferences, you can adjust video and enjoy audio with a greater sense of presence. Operation is the same for HDD and DVD. 1 Press FUNCTION (under the cover) during playback. • The Function Control screen is displayed on the TV.
Settings During Playback Functions which can be set Title Number (Direct Title Skip) • Shows the title number being played back. You can skip to the start of the title. • To skip to the start of a selected title, press Number buttons to enter the title number when this option is highlighted. Chapter Number (Direct Chapter Skip) • Shows the chapter number being played back. You can skip to the start of the chapter.
Simultaneous Recording/Playback Function HDD DVD-RW DVD-RW VR MODE VIDEO MODE VIDEO CD DVD-R DVD VIDEO Plays back from HDD, DVD or CD while recording a programme onto HDD. Chasing Playback Viewing the Programme Being Recorded from the Beginning while Recording to HDD 1 Press G REV or during recording. Press G REV or J FWD during Chasing Playback. • Each time you press the buttons, the Fast Reverse/Forward Playback speed changes as shown below.
Function Menu How to Use the FUNCTION MENU HDD DVD-RW DVD-RW VR MODE VIDEO MODE DVD-R The following is the example of HDD. Actual menu items differ according to each type of media (HDD, DVD-RW or DVD-R) and whether Original or Play List.
Editing (HDD/DVD) Available Features for Editing by Recording Format on HDD/DVD DVD VR format Video format ✕ ✕ ✕ ✕ - HDD DIVIDE CHAPTER ERASE SCENE EDITING PLAYLIST EDITING BY FRAME ✕ ✕ ✕ ✕* SEAMLESS PLAYBACK ✕ - ✕ * Titles recorded with “HI SP DUB SETTING” set as “YES” cannot be edited by frame. If you are to edit a title by frame, set “HI SP DUB SETTING” as “NO” prior to recording of the title. Editing Procedure Basic procedure for editing an original title recorded in VR mode Load a disc.
Editing (HDD/DVD) Edit Screen 22 / 7 [FRI] 10 : 10 HDD REMAIN: XP 20h00m EDITING (HDD: ORIGINAL) 1 PR 1 SP BBC2 21 / 5 SAT 10 : 00 ERASE SCENE CHANGE THUMBNAIL DIVIDE CHAPTER COMBINE CHAPTERS Chapter being edited 60 m. SP 1 1 00 : 00: 01 01 Time being edited SPECIFY RANGE TO DELETE.
Editing an Original Title (HDD/DVD) HDD 22 / 7 [FRI] 10 : 10 HDD REMAIN: XP 20h00m REC LIST (HDD: ORIGINAL) Erasing Unnecessary Scenes from an Original Title (ERASE SCENE) 1 BBC2 21 / 5 PR 1 SP 60 m. SP SAT 10 : 00 1 2 NEW NEW DVD-RW 4 3 5 6 VR MODE Selects a scene from an original video and erase it. • To erase all titles, see page 95. • To erase by title (or chapter), see page 95. • Read the explanation on page 81 and 82 before starting editing.
Editing an Original Title (HDD/DVD) • When the start point is set to near the beginning of a chapter, the beginning of the chapter will be selected as the start point. To make the original designated start point effective, set it again after combining up with the chapter just before. (Page 87) 9 Press SET/ENTER when you reach the end of scene to be erased. • The erase end point is set. (The title will pause.) • As the erase end point, you can not select a point which precedes the erase start point.
Editing an Original Title (HDD/DVD) Changing Thumbnail (CHANGE THUMBNAIL) HDD 6 1 Press ' / " to select “CHANGE THUMBNAIL”. 22 / 7 [FRI] 10 : 10 HDD REMAIN: XP 20h00m EDITING (HDD: ORIGINAL) DVD-RW 1 PR 1 SP BBC2 21 / 5 SAT 10 : 00 ERASE SCENE CHANGE THUMBNAIL DIVIDE CHAPTER COMBINE CHAPTERS VR MODE Changes the still frame picture displayed at the Thumbnail screen of the REC LIST to your favourite scene within the title. 60 m. SP 1 1 00 : 00: 01 01 SPECIFY SCREEN TO CHANGE.
Editing an Original Title (HDD/DVD) Making Sections in a Title (DIVIDE CHAPTER) HDD 5 Press \ / | to select “YES”, then press SET/ENTER. 6 Press ' / " to select “DIVIDE CHAPTER”, then press SET/ENTER. DVD-RW VR MODE This function divides a title into multiple chapters and makes it easier to find scenes, edit and dub a chapter as a unit. 1 • Switch to the drive (HDD or DVD) to be edited. 1 2 1 1 00 : 00: 01 01 Press |PLAY to start playback.
Editing an Original Title (HDD/DVD) Combining Chapters Together (COMBINE CHAPTERS) HDD DVD-RW VR MODE Combines up to 10 adjacent chapters into a single chapter. NOTE • You cannot combine chapters automatically recorded when a scene was erased. Before Starting Editing • Switch to the drive (HDD or DVD) to be edited. 1 Select (“REC LIST”) in “START MENU” screen, then press SET/ENTER. • To select a title in the title list, press Red (A). 2 3 Press ' / " / \ / | to select the title you wish to edit.
Editing a Play List (HDD/DVD) Creating a Play List HDD 4 1 Press ' / " to select “COPY TITLE/CHAPTER”. 2 Press SET/ENTER. 5 1 Press ' / " / \ / | to select title to copy. DVD-RW VR MODE You can create a Play List by copying a title or chapter units from an original. Also you can select your favourite scenes from originals, and compile them into a Play List. HDD REMAIN: XP 1 NOTE • Operations like “COPY TITLE/CHAPTER” and “COPY SPECIFIED SCENE” do not actually copy the original titles.
Editing a Play List (HDD/DVD) • When the start point is set to near the beginning of a chapter, the beginning of the chapter will be selected as the start point. To make the original designated start point effective, set it again after combining up with the chapter just before. (page 87) 6 Find the place where you want to end copying, then press SET/ ENTER. • If you press RETURN, you can reselect the start point.
Editing a Play List (HDD/DVD) 5 Adding a Title or Chapter 1 Select “ADD TITLE/CHAPTER”, then press SET/ENTER. 2 Select a title (chapter) to add using ' / " / \ / |, then press SET/ENTER. Go to Step 9. • When the start point is set to near the beginning of a chapter, the beginning of the chapter will be selected as the start point. To make the original designated start point effective, set it again after combining up with the chapter just before.
Editing a Play List (HDD/DVD) Changing the Title Sequence (MOVE TITLE) HDD 7 Press SET/ENTER. • If a point prior to the selected title is selected as the destination, the title will move to the point immediately prior to the selected title. DVD-RW VR MODE Example: If Title 3 is selected and the destination cursor is set to Title 1, Title 3 is moved to the spot in front of Title 1. • Freely changes the sequence of titles. • Follow the same procedure both in “title list” and in “thumbnail”.
Editing a Play List (HDD/DVD) The operations in this page is in common with those to edit “original” titles. Erasing Unnecessary Scenes (ERASE SCENE) HDD DVD-RW Making Sections in a Title (DIVIDE CHAPTER) HDD VR MODE DVD-RW VR MODE Selects and erases unnecessary scenes. Even if you erase a scene in a play list, this will not affect the original video. Divides a title into multiple chapters. This makes editing and dubbing in chapter units more convenient.
Disc Management Inputting/Changing Title Name (CHANGE TITLE NAME) HDD DVD-RW DVD-RW VR MODE VIDEO MODE 6 • Title Name Change screen appears. 7 NOTE • Title names cannot be changed in finalised Video mode discs. Input field (Displays title name. Can input and change title name.) Cursor (Displays the position to input characters.) Displays input characters. Select when you switch between capital letters and small letters. Before Starting Editing • Switch to the drive (HDD or DVD) to be edited.
Disc Management 10 Press ' / " / \ / | to select “END” and then press SET/ENTER After input is finished. To Cancel Title Protect 1 • The new title is set, and the screen in Step 5 is displayed. 11 Press EXIT to quit editing. • Edit mode will terminate. Disabling Title Edit and Erase (TITLE PROTECT) HDD DVD-RW 2 Select the title protected in Step 2 above, and follow the Steps 3 and 4 above. Select “NO” in the Step 5 above, then press SET/ENTER.
Disc Management Erasing by Selecting a Title (or Chapter) Erasing All Titles HDD DVD-RW DVD-RW VR MODE VIDEO MODE DVD-R This erases the entire contents of an HDD or DVD-RW. (Except titles for which title protect has been set.) You can erase the following: • HDD (ORIGINAL): Erases all titles recorded on the HDD. When originals are erased, play lists are also erased. • HDD (PLAY LIST): Erases all play lists created on the HDD. Even if play lists are erased, the original titles are not erased.
Initialise/Finalise See also page 15 for information on Initialisation and Finalisation. Initialisation Before recording to DVD-RW, initialise the disc in VR mode or Video mode. You can also initialise the HDD. Initialise the HDD only after dubbing important recordings onto DVD-RW/R disc(s). Finalisation Finalisation is done so that a recorded DVD-RW/R disc can be played back with other recorders.
Initialise/Finalise Basic Operation for INITIALISE/FINALISE 4 • The message asks “OK”? 2 Press \ / | to select “YES”, then press SET/ENTER. Example: Initialising DVD in VR mode 1 • Initialising (or finalising) will be executed. 1 Press START MENU to display “START MENU” screen. 2 Press ' / " / \ / | to select 24 / 12 [SAT] 10 : 28 INITIALISE DVD INITIALISE (VR) DVD INITIALISE (VIDEO) INITIALISE HARD DISC (“INITIALISE/FINALISE”), then press SET/ENTER. START MENU [INITIALISE/FINALISE] 1 Press \ / |
Enjoying High Quality Sounds Playing 2 Channel Audio with an Analogue Connection The Recorder (Red) (White) To AUDIO Output jacks Audio cable (commercially available) (Red) (White) Playing Dolby Digital, DTS or MPEG Audio with a Digital Connection • Connecting an amplifier with a Dolby Digital/DTS/MPEG Audio digital surround processor or a Dolby Digital/DTS/ MPEG Audio digital surround amplifier to the Recorder’s coaxial or optical DIGITAL AUDIO Output jack (terminal)* provides richer, more powerful
Enjoying High Quality Sounds Playing 2 Channel Audio with a Digital Connection Digital Connection to an MD Recorder or Other Audio Equipment without a Dolby Digital Decoder Audio CD or Video CD The Recorder • You can enjoy these discs by playing them back by the ordinary playback procedure. (The normal audio output is not played back for discs recorded with DTS.
Recording from External Equipment Recording from a Digital Camcorder Using i.LINK (DV-HR480H only) HDD DVD-RW DVD-RW VR MODE VIDEO MODE DVD-R About DV Input • When this Recorder is connected with a DV-format digital camcorder using a DV cable, you can record and edit with minimal deterioration of picture and sound quality using a digital signal. (DV LINK) • You can also display an operation panel for digital camcorder control on the screen, and operate using the buttons on the panel.
Recording from External Equipment Settings for Recording from a Digital Camcorder (DV-HR480H only) HDD DVD-RW DVD-RW VR MODE VIDEO MODE 2 DVD-R 1 Press ' / " to select “DV LINK SETTING”, and then press SET/ENTER. 2 Press \ / | to select “YES”, and then press SET/ENTER.
Recording from External Equipment Recording from a Digital Camcorder (DV-HR480H only) 3 Start playback on the digital camcorder. • When “DV LINK SETTING” is set to “YES”, the on-screen control panel allows you to operate the camcorder. To specify a function, press ' / " / \ / | to select the desired button, and then press SET/ENTER. • When “DV LINK SETTING” is set to “NO”, use the operation buttons on the camcorder.
Recording from External Equipment Recording from a Camcorder (VCR) Using an Analogue Connection HDD DVD-RW DVD-RW VR MODE VIDEO MODE 1 2 NOTE • More vivid images can be viewed by connecting the SVIDEO input jack on this Recorder with the S-video output jack on the camcorder using an S-video cable. • Some camcorders may require a special cable for connection. • Refer to the operation manual provided with the camcorder for further information on the procedure for connecting the camcorder.
Function Setting Functions under OTHER SETTINGS This section explains various settings relating to recording and playback which can be used to get more out of the Recorder. • For details about each setting, see the corresponding pages.
Function Setting REC FUNCTION ALTERNATIVE REC SET (ALTERNATIVE REC SETTING) • This function is for diverting the recording destination from DVD-RW/R to HDD when a recording set to DVD-RW/R cannot work due to the disc situation. This function works in the following cases. * 1 When there is not enough disc capacity left in DVD. 2 When an unrecordable disc is loaded. 3 When you forget to load a disc. 4 When a disc is playing within 2 minutes prior to the start of timer recording.
Function Setting Basic Operation for REC FUNCTION Setting This operation is available in both HDD mode and DVD mode. Example: Setting “EXTERNAL IN AUDIO” under “REC FUNCTION” 1 1 Press START MENU to display “START MENU” screen. 2 Press ' / " / \ / | to select (“OTHER SETTINGS”), then press SET/ENTER. START MENU [OTHER SETTINGS] 24 / 12 [SAT] 10 : 28 DISPLAYS SETTINGS BEFORE REC/PLAYBACK 2 Press \ / | to select “REC FUNCTION”.
Function Setting VIEW/PLAY SET DVD PLAYBACK SETTING PARENTAL CNTRL LEVEL (PARENTAL CONTROL LEVEL) • This lets you set Parental Control Level depending on disc content. • Level 1 – Level 8 (The smaller the number, the greater the level of restriction.) • When “PARENTAL CNTRL” is set to “OFF”, DVD discs can be played back regardless of the parental level. • Parental Control Level cannot be set if a password has not been set. OFF, LEVEL:1-8 COUNTRY CODE * Refer to the Country Code List below.
Function Setting VIEW/PLAY SET PRESET MANUAL TUNING*1 CHANNEL SETTING • This lets you preset the channels into memory. A maximum of 84 channels can be preset. 1 - 84 CHANNEL • For details, see “CHANNEL SETTING” on page 29. CHXX FINE TUNING • This lets you obtain sharp colour picture. DECODER • If there is a separate decoder connected to the L2 terminal of the Recorder, set this function to “ON” in order to record the unscrambled signal and/or watch it on your TV.
Function Setting VIEW/PLAY SET PIC QUALITY CONTROL (PICTURE QUALITY CONTROL) PASSWORD SETTING BLOCK NOISE REDUCTION ON OFF • This reduces MPEG block noise that tends to arise with fast moving images, typically in recordings by low quality mode such as EP. MOSQUITO NOISE REDUCTION ON OFF • This reduces video artifacts on the edge of the image. PASSWORD 4 digit number • This sets the password for setting or changing Parental Control Level.
Function Setting OTHER SETTINGS [VIEW/PLAY SET: DVD PLAYBACK SETTING] 24 / 12 [SAT] 10 : 28 Basic Operation for VIEW/PLAY SET PARENTAL CNTRL LEVEL DISC LANGAUGE ANGLE MARK DISPLAY SET PARENTAL CONTROL FOR DVD VIDEO. SET PARENTAL CONTROL LEVEL. This operation is available in both HDD mode and DVD mode. OFF SET THE COUNTRY CODE. GERMANY Example: Setting “DVD PLAYBACK SETTING” under “VIEW/PLAY SET” 1 SELECT 1 Press START MENU to display “START MENU” screen. 2 Press ' / " / \ / | to select (“OTHER SETT
Function Setting ADJUSTMENT CLOCK • The clock will normally be set using the VPS/PDC information when your Recorder automatically tunes in the broadcast channels. If for any reason the VPS/PDC signals are not present, your Recorder will not be able to set the clock. The “CLOCK” function lets you set the clock manually. For the “ADJUSTMENT” field, select “AUTO” if you want the recorder to adjust time automatically.
Function Setting ADJUSTMENT • You can set this to enjoy LPCM, Dolby Digital sound, DTS or MPEG sound when connecting with digital input compatible device using Digital cable. LPCM DGTL AUDIO OUT SET VIDEO/AUDIO SETTING • Select the appropriate option. • Select “AUTO” usually. • If your amplifier/decoder is NOT compatible with 96kHz LPCM, select “48kHz”. 96kHz sound will be output in 48kHz. • If your amplifier/decoder is compatible with 96kHz LPCM, select “96kHz”. 96kHz sound will be output.
Function Setting ADJUSTMENT DV SETTING DV LINK SETTING (DV-HR480H only) NO: Select this when you cannot operate the camcorder properly with the On-screen Control Panel. YES: This lets you operate the camcorder using the On-screen Control Panel. NO YES DV IN AUDIO SETTING STEREO 1*: This lets you capture audio you recorded with the camcorder. STEREO 2*: This lets you capture camcorder’s audio you recorded using after recording.
Function Setting Basic Operation for ADJUSTMENT Setting Example: Setting “VIDEO/AUDIO SETTING” under “ADJUSTMENT” 1 1 Press START MENU to display “START MENU” screen. 2 Press ' / " / \ / | to select (“OTHER SETTINGS”), then press SET/ENTER. START MENU [OTHER SETTINGS] 24 / 12 [SAT] 10 : 28 DISPLAYS SETTINGS BEFORE REC/PLAYBACK SELECT 2 ENTER ENTER n RETURN EXIT EXIT Press \ / | to select “ADJUSTMENT”.
Function Setting CONTROL SET AUTO POWER OFF SET • This sets the Recorder so that power is automatically shut off if it is in stopped state for about 3 hours. YES NO LCD BACKLIGHT SET • This sets whether to turn the LCD backlight on or off during timer recording. NO: This sets so that the LCD backlight remains lit, even during timer recording. YES: This lets you turn off the LCD backlight only when the power is off (standby state) and timer recording starts.
Function Setting Basic Operation for CONTROL SET Example: Setting “LCD BACKLIGHT SET” under “CONTROL SET” 1 1 Press START MENU to display “START MENU” screen. 2 Press ' / " / \ / | to select (“OTHER SETTINGS”), then press SET/ENTER. START MENU [OTHER SETTINGS] 24 / 12 [SAT] 10 : 28 DISPLAYS SETTINGS BEFORE REC/PLAYBACK SELECT 2 ENTER ENTER n RETURN EXIT EXIT Press \ / | to select “CONTROL SET”.
Troubleshooting The following problems do not always suggest a defect or malfunction of this Recorder. Perform the checks listed below before calling for service. Problem Suggested Solution The Recorder power cannot be turned on. • Is the power cord firmly plugged into the AC outlet? • When the power cord is plugged into a power outlet, press RESET, and once the STANDBY indicator is lit, turn on the power. (page 120) • Press OPERATE after the STANDBY indicator turns on.
Troubleshooting Problem Suggested Solution The picture from external input is distorted. • If the signal is copy-protected, you cannot connect via this Recorder. Connect the external equipment directly to your TV. The screen is stretched vertically or horizontally. • Set the TV mode according to the TV you are connecting.(Page 111) • If the above operation does not set the TV mode, set it using the functions of the connected TV.
Troubleshooting Problem Suggested Solution Horizontally wide video appears vertically tall, or black bands appear at the top and bottom of the screen.
Troubleshooting Problem Suggested Solution Cannot display TV listings. Cannot set timer recording with GUIDE Plus+ system.
On-screen Error Messages Messages Relating to DVD and HDD • The following messages appear on the TV screen in case the disc you tried to playback is not appropriate or the operation is not correct. Error message CANNOT PLAY THIS DISC. INCOMPATIBLE DISC. CANNOT OPERATE. DISC IS PROTECTED. COULD NOT REPAIR THE DISC. COULD NOT FINALISE. RECORDING PROHIBITED. CANNOT RECORD. TITLE (CHAPTER) IS FULL. CANNOT RECORD ANY MORE. CANNOT RECORD ON THIS DISC. NO CASSETTE IN CAMCORDER.
On-screen Error Messages Error message INCOMPATIBLE DISC. CANNOT RECORD THIS PROGRAM ON THIS DISC. TIMER PROGRAM COULD NOT START. RECORDING PROHIBITED. STOPPED RECORDING AND RETURNED TO LIVE BROADCAST. RECORDING PROHIBITED, CANNOT RECORD. ERROR IN HDD. CANNOT OPERATE. CAN ONLY VIEW LIVE BROADCASTS. CONTACT THE NEAREST SERVICE CENTRE APPROVED BY SHARP. SYSTEM ERROR. TURNING THE POWER OFF. RECORDING PROHIBITED. CANNOT VIEW TIME SHIFT.
On-screen Error Messages Error message Possible Error Suggested Solution TITLE PROTECTION IS SET. CANCEL TITLE PROTECTION BEFORE DUBBING. • Occurs when you attempt to dub a title containing a “Copy Once” part for which title protection has been set. PROGRAM IS COPY PROTECTED. CANNOT DUB TO THIS DISC. • Occurs if you attempt to dub a title containing a “Copy Once” part to DVD-R or a non-CPRM compatible DVD-RW. • Occurs if an unrecordable disc is loaded (i.e.
Glossary Alternative Recording If you set to Exact Recording but the timer recording programme will not fit into a single DVD-RW/R, the Recorder will automatically perform Alternative Recording to HDD. The Recorder will also perform Alternative Recording to HDD if you forget to load a DVD-RW/R. Angle Recorded onto some DVD discs are scenes which have been simultaneously shot from a number of different angles (the same scene is shot from the front, from the left side, from the right side, etc.).
Glossary G-LINK jack This is a jack in the back of the Recorder to connect Infrared transmitter through G-LINK cable so that you can control your external receiver from the Recorder. GUIDE Plus+ An interactive on-screen television programming guide. You can set timer recording easily with one-touch from an electronic programme listing table.
Glossary REC LIST This is a list screen which lets you check the recorded programmes (titles) in list form. You can select either Thumbnail or Title List as the REC LIST. Region Number Number identifying a geographic region of compatibility for a DVD. Remote Control Code This is the type of the remote control signal for operating the recorder. There are two types of remote control signal: “Remote Control No. 1” (RC-1) and “Remote Control No. 2” (RC-2).
Specifications General HDD capacity: ................................ 250 GB (DV-HR480H), 80 GB (DV-HR400H) Power supply: ................................. AC 220-240 V, 50 Hz Power consumption (Normal): ........ 36 W Power consumption (Standby): ...... 1.5 W (When the Front Panel Display is off) Dimensions: .................................... Approx. 430 mm × 59 mm × 323 mm (W × H × D) Approx. 1615/16″ × 221/64″ × 1223/32″ Weight: ............................................ Approx. 5.3 kg (11.
TERMS OF GUARANTEE GUARANTEE Sharp Electronics (UK) Ltd. (“Sharp”) guarantees to provide for the repair, or at its option the replacement, of this product subject to the conditions listed below:1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It does not cover faults or damage caused by accident, misuse, fair wear and tear, neglect, tampering with the product, or repair other than by a Service Facility appointed by Sharp. 2.
SHARP CORPORATION SHARP ELECTRONICS (U.K.) LTD.
