User manual

Contents/Precautions
8
Handling near electronic medical equipment
Warning
If you have electronic medical equipment such as an
implanted cardiac pacemaker or an implanted
cardioverter-defibrillator, always carry or use your
handset at least 15 cm away from your implant.
Electromagnetic signals may have harmful effects on the
operation of the electronic medical equipment.
Patients receiving medical treatment away from a
medical facility (e.g. home treatment) who are using
electronic medical equipment other than implanted
cardiac pacemakers or implanted cardioverter-
defibrillators should consult the respective
manufacturers etc. for information regarding the
effects of signals on the equipment.
Electromagnetic signals may have harmful effects on the
operation of the electronic medical equipment.
If there is any chance that the distance between the
handset and a person closest to you may get
shorter than 15 cm such as when you cannot freely
move around, set the handset not to emit radio wave
in advance (by setting Airplane mode, turning the
power off, etc.).
Somebody nearby may be equipped with electronic medical
equipment such as an implanted cardiac pacemaker or an
implanted cardioverter-defibrillator. Electromagnetic signals
may have harmful effects on the operation of the electronic
medical equipment.
Follow the instructions given by the respective
medical facilities regarding the use of the handset
on their premises.
Material list
Handset
Disney smartphone pierce SH01
General notes
DM-01H is waterproof/dustproof, however, do not allow
foreign object such as liquids or dust to get inside the
handset and do not allow foreign object such as liquids or
dust to adhere to accessories or optional parts.
The adapter, docomo nano UIM card and Disney smartphone pierce
are not waterproof/dustproof. Do not use in humid or steamy areas
such as bathrooms and avoid exposing to rain and other forms of
moisture. If they are carried close to the skin, perspiration may cause
internal components to corrode and result in malfunction. Note that if a
problem is found to be due to moisture, the handset and parts are not
covered by warranty and in some cases may be irreparable. Even
when repairs are possible, repair charges will be incurred, since the
damage is not covered by warranty.
Clean only with a soft and dry cloth (such as the type used
for eyeglasses).
･ Forceful rubbing of the display with a dry cloth etc. may scratch its
surface.
･ Water drops, dirt, etc. left on the display may cause stains to form on
its surface.
･ Never use chemicals such as alcohol, thinners, benzene or
detergents, as these agents may erase the printing or cause
discoloration.
Occasionally clean terminals with a dry cotton swab etc.
Dirty terminals may result in poor connections and loss of power or
insufficient battery charge. Keep the terminals clean with a dry cotton
swab etc.
Be careful with the terminals while cleaning them.
Do not place the equipment near an air conditioning vent.
Condensation formed due to rapid changes in temperature may cause
internal corrosion and lead to a malfunction.
Part Material/Surface treatment
Display side
Reinforced glass/Shatterproof
sheet of surface
Surrounding area of display side PA resin/UV coating for surface
Upper surface
PC + ABS resin/UV coating for
surface
Bottom surface PA resin/UV coating for surface
Sides
PC + ABS resin/UV coating for
surface
Back
PMMA + PC resin/Hard coating
for surface
Surrounding area of back PA resin/UV coating for surface
docomo nano UIM card slot SUS/Ni plating
microSD Card slot SUS/Ni plating
docomo nano UIM card/microSD
Card slot cover
PC resin/UV coating for surface
Gasket of docomo nano UIM
card/microSD Card slot cover
EPDM
Sticker indicating position for
inserting microSD Card
PET resin/Printing on the back
surface
Instruction
Instruction
Instruction
Instruction
Tray for inserting docomo nano
UIM card
POM resin
IMEI plate PET resin
Power key Aluminum/Anodizing
Side key Aluminum/Anodizing
Camera panel
PMMA + PC resin/Hard coating
for surface
Decoration of camera Aluminum/Anodizing
External connector terminal
SUS/Sn plating, Copper alloy/
Gold plating
Strap pin SUS/Ni plating
Part Material/Surface treatment
Main unit (transparent part) Clear PMMA resin/UV coating
Main unit (metal part)
Clear PMMA resin/AL
evaporation coating
Main unit (sides)
Clear PMMA resin/multi-layer
evaporation coating
Plug (metal part) Copper alloy/Ni plating
Plug (resin part) PP resin
Handling precautions
Part Material/Surface treatment