Infrared Turret Dome Camera User Manual Products: C D600 Series, CD601 Series, CD700 Series Cameras Please read this manual before installing and using this camera and always follow instructions for proper use. Save this manual for future reference.
WARNING Risk of electric shock – do not open. To reduce the risk of electric shock, do not disassemble the camera module. No user serviceable parts are inside. Refer servicing to qualified service personnel. ! WARNING CAUTION CAUTION Do not use the camera if it is emitting fumes, smoke or a strange odor, or if it seems to function abnormally. Disconnect the power source immediately and consult your supplier. Always follow the instructions in the installation guide when applying power.
WARNINGS & CAUTIONS To prevent damage, do not drop the camera or subject it to strong shock or vibration. If installed close to a TV, radio transmitter, magnet, electric motor transformer or audio speakers the magnetic field generated may interfere with or distort the image. Never point it toward the sun. Use caution when operating the camera in the vicinity of spot lights or other bright lights and light reflecting objects.
TABLE OF CONTENTS Table of Contents SECTION 1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Camera components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2 Camera connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SECTION 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 1: FEATURES SECTION 1 Features The CD600, CD601, and CD700 series cameras are weatherproof, vandal resistant turret dome cameras, ideal for outdoor or indoor locations where surveillance in low-light environments is required. These cameras include: • • • • • Advanced image sensors for greater picture clarity Precision lenses to achieve the perfect view (varifocal (VF) cameras have 2.
SECTION 1: FEATURES 1.1 Camera components Video 75 Ohm Drop Cable 12 V dc Base Bezel Camera Housing Camera Module Zoom Adjust (-VF Models) Camera Lens IR LEDs Camera assembly 2 www.observint.
SECTION 1: FEATURES 1.
SECTION 2: INSTALLATION SECTION 2 Installation 2.1 What’s in the box The camera package contains: • • • Camera assembly Instruction manual Hardware kit, including four screws and four wall inserts 2.2 Tools you need To install the camera, you will need: • • Phillips #2 screwdriver Small blade screwdriver (for adjusting VF model cameras) Depending on how the camera is mounted, you may also need: • • • 4 Hammer Drill with 3/32" and 3/16" drill bits 3/4" hole saw www.observint.
SECTION 2: INSTALLATION 2.3 Installation instructions 1. Separate the base from the rest of the camera assembly by unscrewing the housing bezel. Bezel Remove the bezel 2. Determine where the camera will be mounted.
SECTION 2: INSTALLATION 3. Using the base as a template, mark the location of the four mounting screw holes. Mounting screw hole Camera Base 4. Drill mounting screw holes into the mounting surface. a. If the mounting surface is a soft material, such as a drywall, use a 3/16” bit to drill the mounting holes. Use a hammer to tap the wall inserts provided into each hole until they are flush with the surface. OR (continue on next page) 6 www.observint.
SECTION 2: INSTALLATION 5. Drill mounting screw holes into the mounting surface. a. If the mounting surface is a soft material, such as a drywall, use a 3/16" bit to drill the mounting holes. Use a hammer to tap the wall inserts provided into each hole until they are flush with the surface. OR b. If the mounting surface is a very soft material, such as ceiling tile, place a wood block behind the tile. Screws longer than 1" may be required.
SECTION 2: INSTALLATION Cable channel in base 7. Drill a 3/4" hole through the mounting surface at the center of the base. 3/4" Drop cable routing hole Use a #2 Phillips screwdriver to mount the base with the provided screws. 8 www.observint.
SECTION 2: INSTALLATION 8. With the camera in the camera housing, route the drop cable through the 3/4" hole until the camera housing is fitted onto the base. Place the housing bezel over the camera housing and screw it onto the base until the camera and camera housing are held in place. Skip to step 12. 9. Set the camera on the base with the camera cable pressed into one of the cable guides of the base. Allow some slack in the cable within the base to allow for camera positioning later. 10.
SECTION 2: INSTALLATION Reassemble camera 10 www.observint.
SECTION 2: INSTALLATION 12. Attach the BNC video/power cable to the camera cable as required.
SECTION 2: INSTALLATION 2.4 OSD Setup (CD700 series only) CD700 series cameras include on-screen display (OSD) software for adjusting the internal camera settings to complement specific environment where it is installed. These settings are adjusted using the OSD controller attached to the camera drop cable. The OSD controller includes a joystick that can be pushed down and rocked UP, DOWN, left (L) and right (R), or, to open the menu system and navigate the menus.
SECTION 2: INSTALLATION OSD MENU OPTIONS MANUAL LENS AUTO TYPE: DC / VIDEO MODE: CLOSE / AUTO/OPEN SPEED: 0-255 HIGH LUMINANCE MODE: SHUT+AUTO IRIS / AUTO IRIS AUTO SHUTTER/ AGC LOW LUMINANCE MODE: OFF / AGC BRIGHTNESS: ×0.25, ×0.5, ×0.75, ×1 MODE: SHUT+AGC MANUAL OSD SET BRIGHTNESS: 0-255 SHUTTER: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 s AGC: 6, 12, 18, 24, 30, 36, 42, 44.
SECTION 2: INSTALLATION MOTION DET PRIVACY OSD SET (cont.
SECTION 3: AIMING THE CAMERA SECTION 3 Aiming the Camera 1. Connect the video cable from the camera to a test monitor or to the BNC input on the DVR. 2. Apply 12 Vdc power to the camera to power it on. 3. Unscrew the bezel until the camera module and housing can be rotated on the base. 4. While observing the video from the camera, adjust the camera to point it at your surveillance target. 5.
SECTION 4: CLEANING SECTION 4 Cleaning Clean the camera lens and IR lamp shield with an approved glass cleaning solution and a lint free cloth. • • Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a soft cloth. Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
SECTION 5: SPECIFICATIONS SECTION 5 Model Sensor Effective Picture Elements (H×V) Specifications CD600W, CD600B 1/3" CMOS 1/3" SHARP CCD 1/3" SHARP CCD 728 (H) x 488 (V) 768 (H) x 494 (V) 768 (H) x 494 (V) 0.1 lux F1.2 / 0 lux (with IR LED on) 0.1 lux F1.2 / 0 lux (with IR LED on) 0.01 lux F1.
SECTION 5: SPECIFICATIONS Model CD700W, CD700B CD700WVF, CD700BVF Sensor 1/3" SONY Super-HAD CCD II 1/3" SONY Super-HAD CCD II Effective Picture Elements (H×V) 976 (H) x 494 (V) Horizontal Resolution Minimum Illumination 700 TV Line 0.001 lux F1.2 / 0 lux (with IR LED on) S/N Ratio More than 52 dB Scanning System 2:1 interface Synchronous System Internal, negative sync. Auto-electronic Shutter 1/60 s ~ 1/100,000 s Gamma Characteristic IR Distance 0.
SECTION 6: TROUBLESHOOTING SECTION 6 Troubleshooting Before sending the camera for repair, please check below to make sure that the camera is installed correctly. If it still does not perform adequately, please consult your supplier. 1. No picture on the monitor screen. a. Check that all connected devices are powered on. b. Confirm that the voltage is correct. c. Confirm that the power supply provides enough current to power the camera. d. Check that all video cables are correctly connected. 2.
