Operation Guide GB
Table Of Contents
- CONTENTS
- INTRODUCTION
- USING THE MANUAL
- DIFFERENCES BETWEEN MODELS
- SETUP
- BEFORE USING THE MACHINE
- COPY FUNCTIONS
- PRINTER FUNCTIONS
- BASIC PRINTING
- PRINTER DRIVER SETTING SCREEN
- SETTING ADVANCED PRINT FUNCTIONS
- PRINTING MULTIPLE PAGES ON ONE PAGE (N-Up Printing)
- FITTING THE PRINTED IMAGE TO THE PAPER (Fit To Paper Size)
- ROTATING THE PRINT IMAGE 180 DEGREES (Rotate 180 degrees)
- ENLARGING/REDUCING THE PRINT IMAGE (Zoom)
- PRINTING FAINT TEXT AND LINES IN BLACK (Text To Black/Vector To Black)
- ADJUSTING THE BRIGHTNESS AND CONTRAST OF THE IMAGE (Image Adjustment)
- ADDING A WATERMARK TO PRINTED PAGES (Watermark)
- TWO-SIDED PRINTING (Model that has duplex copy / print function as standard feature only)
- SAVING FREQUENTLY USED PRINT SETTINGS
- OUTLINE OF THE PRINT STATUS WINDOW
- BASIC PRINTING (MACINTOSH)
- SCANNER FUNCTIONS
- USER SETTINGS
- TROUBLESHOOTING
- ROUTINE MAINTENANCE
- APPENDIX
- WEB FUNCTIONS IN THE MACHINE
- ABOUT THE WEB PAGES
- CHECKING THE IP ADDRESS IN THE WEB PAGE
- ABOUT THE WEB PAGES (FOR USERS)
- CONFIGURING THE PRINTER CONDITION SETTINGS
- ABOUT THE WEB PAGES (FOR THE ADMINISTRATOR)
- PROTECTING INFORMATION PROGRAMMED IN THE WEB PAGE ([Passwords])
- ADMINISTRATOR SETTINGS
- SSL SETTINGS
- E-MAIL STATUS AND E-MAIL ALERT SETTINGS
94
USER SETTINGS
SELECTING A SETTING FOR A SYSTEM SETTING
1
Hold down the [Light] key ( ) until
the alarm indicators ( , , , , )
blink.
The number of copies
display shows "- -" with
the left hyphen blinking.
2
Enter the program number with the
numeric keys.
• See "SYSTEM
SETTINGS" (p.91 to
p.93) for the program
numbers.
• The selected program
number blinks.
• For example, to select
"Auto clear timer",
press the [1] key.
3
Press the [START] key ( ).
• The selected program
number stops blinking
and lights steadily.
• The currently selected
setting code blinks on
the right side of the
display.
4
Enter the desired setting code by
pressing a numeric key.
• For the setting codes,
see "SYSTEM
SETTINGS". (p.91 to
p.93).
• The selected setting
code blinks.
• For example, to select
90 seconds, press the
[5] key.
5
Press the [START] key ( ).
The selected setting
code stops blinking and
lights steadily.
6
Press the [Light] key ( ) to complete
the settings.
The alarm indicators ( , , , , ) go off
and the display returns to the number of copies
display.
Audible signals (key entry beep, invalid key beep, base setting beep)
The machine sounds three different types of beep signals: a key entry beep that sounds when a valid key is
pressed, an invalid key beep that sounds when an invalid key is pressed, and a base setting beep that sounds
when a setting is the same as the base setting (base settings are explained below). The base setting beep is
initially disabled. If you wish to enable the base setting beep, see "Base setting beep signal" on page 92. If you
wish to change the volume of the beep signals or disable them, see "Audible signals volume" on page 92.
The beep patterns of each type of beep signal are as follows:
Key entry beep ......................... One beep
Invalid key beep ......................Two beeps
Base setting beep ................ Three beeps
Base settings
The base settings are preset standard selections for each copy setting. The base settings are as follows:
Copy ratio ........................................ 100%
Light and Dark indicator ......................... 3
Paper feed location ....... Upper paper tray
ORIGINAL SIZE ..................A4 (8-1/2" x 11")
AUTO/TEXT/PHOTO (/ /)
............................................................ AUTO
If you enter the wrong number, press the
[CLEAR] key ( ) and then enter the correct
number.
Note
If you enter the wrong number, press the
[CLEAR] key ( ) and return to step 2.
To select a setting for another system setting,
press the [CLEAR] key ( ) and then return
to step 2.
Note
Note
AUTO